| /* octSIMtest with SAM3S board definition |
| * |
| * (C) 2019 by sysmocom -s.f.m.c. GmbH, Author:Joachim Steiger <jsteiger@sysmocom.de> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA |
| */ |
| #pragma once |
| #include "board_common.h" |
| #include "simtrace_usb.h" |
| |
| /* Name of the board */ |
| #define BOARD_NAME "OCTSIMTEST" |
| /* Board definition */ |
| #define octsimtest |
| |
| /** oscillator used as main clock source (in Hz) */ |
| #define BOARD_MAINOSC 18432000 |
| /** desired main clock frequency (in Hz, based on BOARD_MAINOSC) */ |
| #define BOARD_MCK 58982400 // 18.432 * 16 / 5 |
| |
| /** Pin configuration **/ |
| |
| /** there is no red LED, but the code needs this second LED, thus we provide an unused pin */ |
| #define PIO_LED_RED PIO_PB13 |
| /** MCU pin connected to green LED, which is actually amber, and the logic is inverted since it is connected to an NPN transistor (used as open drain) */ |
| #define PIO_LED_GREEN PIO_PA4 |
| /** red LED pin definition */ |
| #define PIN_LED_RED {PIO_LED_RED, PIOB, ID_PIOB, PIO_OUTPUT_1, PIO_DEFAULT} |
| /** green LED pin definition */ |
| #define PIN_LED_GREEN {PIO_LED_GREEN, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT} |
| /** LEDs pin definition */ |
| #define PINS_LEDS PIN_LED_RED, PIN_LED_GREEN |
| /** index for red LED in LEDs pin definition array */ |
| #define LED_NUM_RED 0 |
| /** index for green LED in LEDs pin definition array */ |
| #define LED_NUM_GREEN 1 |
| |
| /* Button to force bootloader start (shorted to ground when pressed */ |
| #define PIN_BOOTLOADER_SW {PIO_PA5, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP} |
| |
| // FIXME PA8 is 32khz xtal on octsimtest |
| /* Pull card presence pin high (shorted to ground in card slot when card is present) */ |
| |
| /** Phone connection **/ |
| /* Phone USIM slot 1 VCC pin (VCC_PHONE in schematic) */ |
| #define PIN_USIM1_VCC {PIO_PA25, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT} |
| /* Phone USIM slot 1 RST pin (active low; RST_PHONE in schematic) */ |
| #define PIN_USIM1_nRST {PIO_PA24, PIOA, ID_PIOA, PIO_INPUT, PIO_IT_EDGE | PIO_DEGLITCH } |
| /* Phone I/O data signal input/output (I/O_PHONE in schematic) */ |
| #define PIN_PHONE_IO {PIO_PA22A_TXD1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} |
| /* Phone CLK clock input (CLK_PHONE in schematic) */ |
| #define PIN_PHONE_CLK {PIO_PA23A_SCK1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} |
| /* Pin used to switch level shifter in I/O line between rx (0) and tx (1) */ |
| #define PIN_USIM1_IO_DIR {PIO_PA26, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT} |
| /* Pin used for phone USIM slot 1 communication */ |
| #define PINS_USIM1 PIN_PHONE_IO, PIN_PHONE_CLK, PIN_PHONE_CLK_INPUT, PIN_USIM1_VCC, PIN_PHONE_IO_INPUT, PIN_USIM1_nRST, PIN_USIM1_IO_DIR |
| /* Phone I/O data signal input/output (unused USART RX input; connected to I/O_PHONE in schematic) */ |
| #define PIN_PHONE_IO_INPUT {PIO_PA21A_RXD1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} |
| /* Pin used as clock input (to measure the ETU duration; connected to CLK_PHONE in schematic) */ |
| #define PIN_PHONE_CLK_INPUT {PIO_PA29B_TCLK2, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT} |
| |
| /** Default pin configuration **/ |
| |
| /** External SPI flash interface **/ |
| /* SPI MISO pin definition */ |
| #define PIN_SPI_MISO {PIO_PA12A_MISO, PIOA, PIOA, PIO_PERIPH_A, PIO_PULLUP} |
| /* SPI MOSI pin definition */ |
| #define PIN_SPI_MOSI {PIO_PA13A_MOSI, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT} |
| /* SPI SCK pin definition */ |
| #define PIN_SPI_SCK {PIO_PA14A_SPCK, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT} |
| /* SPI pins definition. Contains MISO, MOSI & SCK */ |
| #define PINS_SPI PIN_SPI_MISO, PIN_SPI_MOSI, PIN_SPI_SCK |
| /* SPI chip select 0 pin definition */ |
| #define PIN_SPI_NPCS0 {PIO_PA11A_NPCS0, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT} |
| /* SPI flash write protect pin (active low, pulled low) */ |
| #define PIN_SPI_WP {PA15, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT} |
| |
| /** Pin configuration to control USB pull-up on D+ |
| * @details the USB pull-up on D+ is enable by default on the board but can be disabled by setting PA16 high |
| */ |
| #define PIN_USB_PULLUP {PIO_PA16, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT} |
| |
| /** USB definitions */ |
| /* OpenMoko SIMtrace 2 USB vendor ID */ |
| #define BOARD_USB_VENDOR_ID USB_VENDOR_OPENMOKO |
| /* OpenMoko SIMtrace 2 USB product ID (main application/runtime mode) */ |
| #define BOARD_USB_PRODUCT_ID USB_PRODUCT_OCTSIMTEST |
| /* OpenMoko SIMtrace 2 DFU USB product ID (DFU bootloader/DFU mode) */ |
| #define BOARD_DFU_USB_PRODUCT_ID USB_PRODUCT_OCTSIMTEST |
| /* USB release number (bcdDevice, shown as 0.00) */ |
| #define BOARD_USB_RELEASE 0x000 |
| /* Indicate SIMtrace is bus power in USB attributes */ |
| #define BOARD_USB_BMATTRIBUTES USBConfigurationDescriptor_BUSPOWERED_NORWAKEUP |
| |
| #define DETECT_VCC_BY_ADC |
| /* we have a resistive voltage divider of 47 + 30 kOhms to also detect 5V supply power */ |
| #define VCC_UV_THRESH_1V8 (1500000*47)/(47+30) |
| #define VCC_UV_THRESH_3V (2500000*47)/(47+30) |
| |
| #define HAVE_SLOT_MUX |
| |
| #define HAVE_BOARD_CARDINSERT |
| struct cardem_inst; |
| void board_set_card_insert(struct cardem_inst *ci, bool card_insert); |
| |
| /** Supported modes */ |
| /* SIMtrace board supports sniffer mode */ |
| //#define HAVE_SNIFFER |
| /* SIMtrace board supports CCID mode */ |
| //#define HAVE_CCID |
| /* SIMtrace board supports card emulation mode */ |
| #define HAVE_CARDEM |
| /* SIMtrace board supports man-in-the-middle mode */ |
| //#define HAVE_MITM |
| /* octsimtest board supports gpio_test mode */ |
| #define HAVE_GPIO_TEST |