/* octSIMtest with SAM3S board definition
 *
 * (C) 2019 by sysmocom -s.f.m.c. GmbH, Author:Joachim Steiger <jsteiger@sysmocom.de>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307, USA
 */
#pragma once
#include "board_common.h"
#include "simtrace_usb.h"

/* Name of the board */
#define BOARD_NAME "OCTSIMTEST"
/* Board definition */
#define octsimtest

/** oscillator used as main clock source (in Hz) */
#define BOARD_MAINOSC 18432000
/** desired main clock frequency (in Hz, based on BOARD_MAINOSC) */
#define BOARD_MCK 58982400 // 18.432 * 16 / 5

/** Pin configuration **/

/** there is no red LED, but the code needs this second LED, thus we provide an unused pin */
#define PIO_LED_RED     PIO_PB13
/** MCU pin connected to green LED, which is actually amber, and the logic is inverted since it is connected to an NPN transistor (used as open drain) */
#define PIO_LED_GREEN   PIO_PA4
/** red LED pin definition */
#define PIN_LED_RED     {PIO_LED_RED, PIOB, ID_PIOB, PIO_OUTPUT_1, PIO_DEFAULT}
/** green LED pin definition */
#define PIN_LED_GREEN   {PIO_LED_GREEN, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
/** LEDs pin definition */
#define PINS_LEDS       PIN_LED_RED, PIN_LED_GREEN 
/** index for red LED in LEDs pin definition array */
#define LED_NUM_RED     0
/** index for green LED in LEDs pin definition array */
#define LED_NUM_GREEN   1

/* Button to force bootloader start (shorted to ground when pressed */
#define PIN_BOOTLOADER_SW      {PIO_PA5, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}

// FIXME PA8 is 32khz xtal on octsimtest
/* Pull card presence pin high (shorted to ground in card slot when card is present) */

/** Phone connection **/
/* Phone USIM slot 1 VCC pin (VCC_PHONE in schematic) */
#define PIN_USIM1_VCC          {PIO_PA25, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
/* Phone USIM slot 1 RST pin (active low; RST_PHONE in schematic) */
#define PIN_USIM1_nRST         {PIO_PA24, PIOA, ID_PIOA, PIO_INPUT, PIO_IT_EDGE | PIO_DEGLITCH }
/* Phone I/O data signal input/output (I/O_PHONE in schematic) */
#define PIN_PHONE_IO           {PIO_PA22A_TXD1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/* Phone CLK clock input (CLK_PHONE in schematic) */
#define PIN_PHONE_CLK          {PIO_PA23A_SCK1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/* Pin used to switch level shifter in I/O line between rx (0) and tx (1) */
#define PIN_USIM1_IO_DIR	{PIO_PA26, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
/* Pin used for phone USIM slot 1 communication */
#define PINS_USIM1              PIN_PHONE_IO, PIN_PHONE_CLK, PIN_PHONE_CLK_INPUT, PIN_USIM1_VCC, PIN_PHONE_IO_INPUT, PIN_USIM1_nRST, PIN_USIM1_IO_DIR
/* Phone I/O data signal input/output (unused USART RX input; connected to I/O_PHONE in schematic) */
#define PIN_PHONE_IO_INPUT     {PIO_PA21A_RXD1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/* Pin used as clock input (to measure the ETU duration; connected to CLK_PHONE in schematic) */
#define PIN_PHONE_CLK_INPUT    {PIO_PA29B_TCLK2, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}

/** Default pin configuration **/

/** External SPI flash interface   **/
/* SPI MISO pin definition */
#define PIN_SPI_MISO  {PIO_PA12A_MISO, PIOA, PIOA, PIO_PERIPH_A, PIO_PULLUP}
/* SPI MOSI pin definition */
#define PIN_SPI_MOSI  {PIO_PA13A_MOSI, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/* SPI SCK pin definition */
#define PIN_SPI_SCK   {PIO_PA14A_SPCK, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/* SPI pins definition. Contains MISO, MOSI & SCK */
#define PINS_SPI       PIN_SPI_MISO, PIN_SPI_MOSI, PIN_SPI_SCK
/* SPI chip select 0 pin definition */
#define PIN_SPI_NPCS0 {PIO_PA11A_NPCS0, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/* SPI flash write protect pin (active low, pulled low) */
#define PIN_SPI_WP    {PA15, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}

/** Pin configuration to control USB pull-up on D+
 *  @details the USB pull-up on D+ is enable by default on the board but can be disabled by setting PA16 high
 */
#define PIN_USB_PULLUP  {PIO_PA16, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}

/** USB definitions */
/* OpenMoko SIMtrace 2 USB vendor ID */
#define BOARD_USB_VENDOR_ID	USB_VENDOR_OPENMOKO
/* OpenMoko SIMtrace 2 USB product ID (main application/runtime mode) */
#define BOARD_USB_PRODUCT_ID	USB_PRODUCT_OCTSIMTEST
/* OpenMoko SIMtrace 2 DFU USB product ID (DFU bootloader/DFU mode) */
#define BOARD_DFU_USB_PRODUCT_ID USB_PRODUCT_OCTSIMTEST
/* USB release number (bcdDevice, shown as 0.00) */
#define BOARD_USB_RELEASE	0x000
/* Indicate SIMtrace is bus power in USB attributes */
#define BOARD_USB_BMATTRIBUTES	USBConfigurationDescriptor_BUSPOWERED_NORWAKEUP

#define DETECT_VCC_BY_ADC
/* we have a resistive voltage divider of 47 + 30 kOhms to also detect 5V supply power */
#define VCC_UV_THRESH_1V8	(1500000*47)/(47+30)
#define VCC_UV_THRESH_3V	(2500000*47)/(47+30)

#define HAVE_SLOT_MUX

#define HAVE_BOARD_CARDINSERT
struct cardem_inst;
void board_set_card_insert(struct cardem_inst *ci, bool card_insert);

/** Supported modes */
/* SIMtrace board supports sniffer mode */
//#define HAVE_SNIFFER
/* SIMtrace board supports CCID mode */
//#define HAVE_CCID
/* SIMtrace board supports card emulation mode */
#define HAVE_CARDEM
/* SIMtrace board supports man-in-the-middle mode */
//#define HAVE_MITM
/* octsimtest board supports gpio_test mode */
#define HAVE_GPIO_TEST