| #ifndef _BOARD_ |
| #define _BOARD_ |
| |
| /** Headers */ |
| #include "chip.h" |
| /* We need this for a nop instruction in USB_HAL.c */ |
| #define __CC_ARM |
| |
| /** Board */ |
| #include "board_lowlevel.h" |
| #include "uart_console.h" |
| #include "iso7816_4.h" |
| #include "led.h" |
| #include "cciddriver.h" |
| #include "usart.h" |
| #include "USBD.h" |
| |
| #include "USBD_Config.h" |
| #include "USBDDriver.h" |
| |
| /** Highlevel */ |
| #include "trace.h" |
| #include "stdio.h" |
| #include "stdlib.h" |
| #include "string.h" |
| #include "inttypes.h" |
| #include "syscalls.h" |
| |
| #define MIN(a, b) ((a < b) ? a : b) |
| |
| #ifdef __GNUC__ |
| #undef __GNUC__ |
| #endif |
| |
| /** Family definition (already defined) */ |
| #define sam3s |
| /** Core definition */ |
| #define cortexm3 |
| |
| #define BOARD_MCK 48000000 |
| |
| #define PIO_LED_RED PIO_PA17 |
| #define PIO_LED_GREEN PIO_PA18 |
| |
| #define PIN_LED_RED {PIO_LED_RED, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT} |
| #define PIN_LED_GREEN {PIO_LED_GREEN, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT} |
| #define PINS_LEDS PIN_LED_RED, PIN_LED_GREEN |
| |
| #define LED_NUM_RED 0 |
| #define LED_NUM_GREEN 1 |
| |
| /** USART0 pin RX */ |
| #define PIN_USART0_RXD {PIO_PA9A_URXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} |
| /** USART0 pin TX */ |
| #define PIN_USART0_TXD {PIO_PA10A_UTXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} |
| |
| #define BOARD_PIN_USART_RXD PIN_USART0_RXD |
| #define BOARD_PIN_USART_TXD PIN_USART0_TXD |
| |
| #define BOARD_ID_USART ID_USART0 |
| #define BOARD_USART_BASE USART0 |
| |
| #define PINS_UART { PIO_PA9A_URXD0|PIO_PA10A_UTXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} |
| |
| /** UART0 */ |
| /** Console baudrate always using 115200. */ |
| #define CONSOLE_BAUDRATE 115200 |
| /** UART peripheral used by the console (UART0). */ |
| #define CONSOLE_UART UART0 |
| /** UART peripheral ID used by the console (UART0). */ |
| #define CONSOLE_ID ID_UART0 |
| /** UART ISR used by the console (UART0). */ |
| #define CONSOLE_ISR UART0_IrqHandler |
| /** UART IRQ used by the console (UART0). */ |
| #define CONSOLE_IRQ UART0_IRQn |
| /** Pins description corresponding to Rxd,Txd, (UART pins) */ |
| #define CONSOLE_PINS {PINS_UART} |
| |
| /// Smartcard detection pin |
| // FIXME: add connect pin as iso pin...should it be periph b or interrupt oder input? |
| #define BOARD_ISO7816_BASE_USART USART0 |
| #define BOARD_ISO7816_ID_USART ID_USART0 |
| |
| /* USART peripherals for a phone and SIM card setup */ |
| /* USART peripheral connected to the SIM card */ |
| #define USART_SIM USART0 |
| /* ID of USART peripheral connected to the SIM card */ |
| #define ID_USART_SIM ID_USART0 |
| /* Interrupt request ID of USART peripheral connected to the SIM card */ |
| #define IRQ_USART_SIM USART0_IRQn |
| /* USART peripheral connected to the phone */ |
| #define USART_PHONE USART1 |
| /* ID of USART peripheral connected to the phone */ |
| #define ID_USART_PHONE ID_USART1 |
| /* Interrupt request ID of USART peripheral connected to the phone */ |
| #define IRQ_USART_PHONE USART1_IRQn |
| |
| #define SIM_PWEN PIO_PA5 |
| #define VCC_FWD PIO_PA26 |
| |
| /** Pin configuration to control USB pull-up on D+ |
| * @details the USB pull-up on D+ is enable by default on the board but can be disabled by setting PA16 high |
| */ |
| #define PIN_USB_PULLUP {PIO_PA16, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT} |
| |
| // Board has UDP controller |
| #define BOARD_USB_UDP |
| // D+ has external pull-up |
| #define BOARD_USB_PULLUP_EXTERNAL |
| |
| #define BOARD_USB_DFU |
| #define BOARD_DFU_BOOT_SIZE (16 * 1024) |
| #define BOARD_DFU_RAM_SIZE (2 * 1024) |
| #define BOARD_DFU_PAGE_SIZE 512 |
| #define BOARD_DFU_NUM_IF 2 |
| |
| extern void board_exec_dbg_cmd(int ch); |
| extern void board_main_top(void); |
| extern int board_override_enter_dfu(void); |
| #endif |