firmware/src_simtrace/simtrace_iso7816.c

/* ----------------------------------------------------------------------------
 *         ATMEL Microcontroller Software Support
 * ----------------------------------------------------------------------------
 * Copyright (c) 2009, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */

/*------------------------------------------------------------------------------
 *          Headers
 *------------------------------------------------------------------------------*/

#include "board.h"
#include "simtrace.h"
#include "ringbuffer.h"
#include "iso7816_fidi.h"

#include <string.h>
#include <errno.h>

volatile uint32_t char_stat;

volatile ringbuf sim_rcv_buf = { {0}, 0, 0 };

/*-----------------------------------------------------------------------------
 *          Interrupt routines
 *-----------------------------------------------------------------------------*/
static void Callback_PhoneRST_ISR(uint8_t * pArg, uint8_t status,
				  uint32_t transferred, uint32_t remaining)
{
	printf("rstCB\n\r");
	PIO_EnableIt(&pinPhoneRST);
}

void ISR_PhoneRST(const Pin * pPin)
{
	int ret;
	// FIXME: no printfs in ISRs?
	printf("+++ Int!! %x\n\r", pinPhoneRST.pio->PIO_ISR);
	if (((pinPhoneRST.pio->PIO_ISR & pinPhoneRST.mask) != 0)) {
		if (PIO_Get(&pinPhoneRST) == 0) {
			printf(" 0 ");
		} else {
			printf(" 1 ");
		}
	}

	if ((ret =
	     USBD_Write(PHONE_INT, "R", 1,
			(TransferCallback) & Callback_PhoneRST_ISR,
			0)) != USBD_STATUS_SUCCESS) {
		TRACE_ERROR("USB err status: %d (%s)\n", ret, __FUNCTION__);
		return;
	}

	/* Interrupt enabled after ATR is sent to phone */
	PIO_DisableIt(&pinPhoneRST);
}

extern void usart_irq_rx(uint8_t num);
/*
 *  char_stat is zero if no error occured.
 *  Otherwise it is filled with the content of the status register.
 */
void USART1_IrqHandler(void)
{
#if 0
	uint32_t stat;
	char_stat = 0;
	// Rcv buf full
/*	if((stat & US_CSR_RXBUFF) == US_CSR_RXBUFF) {
		TRACE_DEBUG("Rcv buf full");
		USART_DisableIt(USART1, US_IDR_RXBUFF);
	}
*/
	uint32_t csr = USART_PHONE->US_CSR;

	if (csr & US_CSR_TXRDY) {
		/* transmit buffer empty, nothing to transmit */
	}
	if (csr & US_CSR_RXRDY) {
		stat = (csr & (US_CSR_OVRE | US_CSR_FRAME |
			       US_CSR_PARE | US_CSR_TIMEOUT | US_CSR_NACK |
			       (1 << 10)));
		uint8_t c = (USART_PHONE->US_RHR) & 0xFF;
//		printf(" %x", c);

		if (stat == 0) {
			/* Fill char into buffer */
			rbuf_write(&sim_rcv_buf, c);
		} else {
			TRACE_DEBUG("e %x st: %x\n", c, stat);
		}		/* else: error occured */

		char_stat = stat;
	}
#else
	usart_irq_rx(0);
#endif
}

/*  FIDI update functions   */
void update_fidi(uint8_t fidi)
{
	int rc;

	uint8_t fi = fidi >> 4;
	uint8_t di = fidi & 0xf;

	rc = compute_fidi_ratio(fi, di);
	if (rc > 0 && rc < 0x400) {
		TRACE_INFO("computed Fi(%u) Di(%u) ratio: %d", fi, di, rc);
		/* make sure UART uses new F/D ratio */
		USART_PHONE->US_CR |= US_CR_RXDIS | US_CR_RSTRX;
		USART_PHONE->US_FIDI = rc & 0x3ff;
		USART_PHONE->US_CR |= US_CR_RXEN | US_CR_STTTO;
	} else
		TRACE_INFO("computed FiDi ratio %d unsupported", rc);
}