| /* ---------------------------------------------------------------------------- |
| * ATMEL Microcontroller Software Support |
| * ---------------------------------------------------------------------------- |
| * Copyright (c) 2009, Atmel Corporation |
| * |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions are met: |
| * |
| * - Redistributions of source code must retain the above copyright notice, |
| * this list of conditions and the disclaimer below. |
| * |
| * Atmel's name may not be used to endorse or promote products derived from |
| * this software without specific prior written permission. |
| * |
| * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR |
| * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE |
| * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, |
| * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT |
| * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, |
| * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF |
| * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING |
| * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, |
| * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| * ---------------------------------------------------------------------------- |
| */ |
| |
| /** |
| * \page usart_iso7816 USART ISO7816 Example |
| * |
| * \section Purpose |
| * This example sends ISO 7816 commands to a smartcard connected to the |
| * evaluation kits on sam3s. |
| * |
| * \section Requirements |
| * This example can be used on sam3s evaluation kit. Please connect the |
| * smartcard contacts with following pins which could be easily wired from |
| * the board. |
| * - <b>SAM3S-EK -- SMARTCARD</b> |
| * - PA11 -- RST |
| * - TXD1(PA22) -- I/O |
| * - SCK1(PA23) -- CLK |
| * |
| * \section Description |
| * The iso7816 software provide in this examples is use to transform APDU |
| * commands to TPDU commands for the smart card. |
| * The iso7816 provide here is for the protocol T=0 only. |
| * The send and the receive of a character is made under polling. |
| * In the file ISO7816_Init is defined all pins of the card. User must have to |
| * change this pins according to his environment. |
| * The driver is compliant with CASE 1, 2, 3 of the ISO7816-4 specification. |
| * |
| * \section Usage |
| * -# Build the program and download it inside the evaluation board. Please |
| * refer to the <a href="http://www.atmel.com/dyn/resources/prod_documents/doc6224.pdf">SAM-BA User Guide</a>, |
| * the <a href="http://www.atmel.com/dyn/resources/prod_documents/doc6310.pdf">GNU-Based Software Development</a> |
| * application note or to the <a href="ftp://ftp.iar.se/WWWfiles/arm/Guides/EWARM_UserGuide.ENU.pdf">IAR EWARM User Guide</a>, |
| * depending on your chosen solution. |
| * -# On the computer, open and configure a terminal application (e.g. |
| * HyperTerminal on Microsoft Windows) with these settings: |
| * - 115200 bauds |
| * - 8 data bits |
| * - No parity |
| * - 1 stop bit |
| * - No flow control |
| * -# Connect the card reader to sam3s-ek board: |
| * <table border="1" cellpadding="2" cellspacing="0"> |
| * <tr><td>C1: Vcc: 7816_3V5V </td><td> C5: Gnd</td> <td> C4: RFU</td></tr> |
| * <tr><td> C2: Reset: 7816_RST</td> <td> C6: Vpp</td> <td> C8: RFU</td></tr> |
| * <tr><td> C3: Clock: 7816_CLK</td> <td> C7: 7816_IO</td> </tr> |
| * </table> |
| * If necessary,another pin must be connected on the card reader for detecting the |
| * insertion and removal: 7816_IRQ. |
| * On Atmel boards, all this pins can be easily connecting with jumpers. |
| * -# Start the application. The following traces shall appear on the terminal: |
| * \code |
| * -- USART ISO7816 Example xxx -- |
| * -- xxxxxx-xx |
| * -- Compiled: xxx xx xxxx xx:xx:xx -- |
| * Display the ATR |
| * \endcode |
| * |
| * \section References |
| * - usart_iso7816/main.c |
| * - iso7816_4.c |
| * - pio.h |
| * - usart.h |
| * |
| */ |
| |
| /** \file |
| * |
| * This file contains all the specific code for the usart_iso7816 example. |
| * |
| */ |
| |
| |
| /*------------------------------------------------------------------------------ |
| * Headers |
| *------------------------------------------------------------------------------*/ |
| |
| #include "board.h" |
| |
| #include <string.h> |
| |
| /*------------------------------------------------------------------------------ |
| * Internal definitions |
| *------------------------------------------------------------------------------*/ |
| |
| /** Maximum ucSize in bytes of the smartcard answer to a command.*/ |
| #define MAX_ANSWER_SIZE 10 |
| |
| /** Maximum ATR ucSize in bytes.*/ |
| #define MAX_ATR_SIZE 55 |
| |
| /*------------------------------------------------------------------------------ |
| * Internal variables |
| *------------------------------------------------------------------------------*/ |
| |
| /** Test command #1.*/ |
| static const uint8_t testCommand1[] = {0x00, 0x10, 0x00, 0x00}; |
| /** Test command #2.*/ |
| static const uint8_t testCommand2[] = {0x00, 0x20, 0x00, 0x00, 0x02}; |
| /** Test command #3.*/ |
| static const uint8_t testCommand3[] = {0x00, 0x30, 0x00, 0x00, 0x02, 0x0A, 0x0B}; |
| /* Select MF */ |
| static const uint8_t testCommand4[] = {0x00, 0xa4, 0x00, 0x00, 0x02, 0x3f, 0x00}; |
| /** ISO7816 pins */ |
| static const Pin pinsISO7816[] = {PINS_ISO7816}; |
| /** ISO7816 RST pin */ |
| static const Pin pinIso7816RstMC = PIN_ISO7816_RSTMC; |
| static uint8_t sim_inserted = 0; |
| /*------------------------------------------------------------------------------ |
| * Internal functions |
| *------------------------------------------------------------------------------*/ |
| |
| /*------------------------------------------------------------------------------ |
| * Optional smartcard detection |
| *------------------------------------------------------------------------------*/ |
| |
| #ifdef SMARTCARD_CONNECT_PIN |
| |
| /** Smartcard detection pin.*/ |
| static const Pin pinSmartCard = SMARTCARD_CONNECT_PIN; |
| |
| /** |
| * PIO interrupt service routine. Checks if the smartcard has been connected |
| * or disconnected. |
| */ |
| static void ISR_PioSmartCard( const Pin *pPin ) |
| { |
| /* FIXME: why is pinSmartCard.pio->PIO_ISR the wrong number? |
| printf("+++++ Trying to check for pending interrupts (PIO ISR: 0x%X)\n\r", pinSmartCard.pio->PIO_ISR); |
| printf("+++++ Mask: 0x%X\n\r", pinSmartCard.mask); |
| Output: |
| +++++ Trying to check for pending interrupts (PIO ISR: 0x400)) = 1<<10 |
| +++++ Mask: 0x100 = 1<<8 |
| */ |
| /* Check all pending interrupts */ |
| if ( (pinSmartCard.pio->PIO_ISR & pinSmartCard.mask) != 0 ) |
| { |
| /* Check current level on pin */ |
| if ( PIO_Get( &pinSmartCard ) == 0 ) |
| { |
| sim_inserted = 1; |
| printf( "-I- Smartcard inserted\n\r" ) ; |
| } |
| else |
| { |
| sim_inserted = 0; |
| printf( "-I- Smartcard removed\n\r" ) ; |
| } |
| } |
| } |
| |
| /** |
| * Configures the smartcard detection pin to trigger an interrupt. |
| */ |
| static void ConfigureCardDetection( void ) |
| { |
| printf("+++++ Configure PIOs\n\r"); |
| PIO_Configure( &pinSmartCard, 1 ) ; |
| NVIC_EnableIRQ( PIOA_IRQn ); |
| // FIXME: Do we need to set priority?: NVIC_SetPriority( PIOA_IRQn, 10); |
| PIO_ConfigureIt( &pinSmartCard, ISR_PioSmartCard ) ; |
| PIO_EnableIt( &pinSmartCard ) ; |
| } |
| |
| #else |
| |
| /** |
| * Dummy implementation. |
| */ |
| static void ConfigureCardDetection( void ) |
| { |
| printf( "-I- Smartcard detection not supported.\n\r" ) ; |
| } |
| |
| #endif |
| |
| /** |
| * Displays a menu which enables the user to send several commands to the |
| * smartcard and check its answers. |
| */ |
| static void SendReceiveCommands( void ) |
| { |
| uint8_t pMessage[MAX_ANSWER_SIZE]; |
| uint8_t ucSize ; |
| uint8_t ucKey ; |
| uint8_t command; |
| uint8_t i; |
| |
| /* Clear message buffer */ |
| memset( pMessage, 0, sizeof( pMessage ) ) ; |
| |
| /* Display menu */ |
| printf( "-I- The following three commands can be sent:\n\r" ) ; |
| printf( " 1. " ) ; |
| for ( i=0 ; i < sizeof( testCommand1 ) ; i++ ) |
| { |
| printf( "0x%X ", testCommand1[i] ) ; |
| } |
| printf( "\n\r 2. " ) ; |
| |
| for ( i=0 ; i < sizeof( testCommand2 ) ; i++ ) |
| { |
| printf( "0x%X ", testCommand2[i] ) ; |
| } |
| printf( "\n\r 3. " ) ; |
| |
| for ( i=0 ; i < sizeof( testCommand3 ) ; i++ ) |
| { |
| printf( "0x%X ", testCommand3[i] ) ; |
| } |
| printf( "\n\r 4. " ) ; |
| |
| for ( i=0 ; i < sizeof( testCommand4 ) ; i++ ) |
| { |
| printf( "0x%X ", testCommand4[i] ) ; |
| } |
| printf( "\n\r" ) ; |
| |
| /* Get user input */ |
| ucKey = 0 ; |
| while ( ucKey != 'q' ) |
| { |
| printf( "\r " ) ; |
| printf( "\rChoice ? (q to quit): " ) ; |
| #if defined ( __GNUC__ ) |
| fflush(stdout); |
| #endif |
| ucKey = UART_GetChar() ; |
| printf( "%c", ucKey ) ; |
| command = ucKey - '0'; |
| |
| /* Check user input */ |
| ucSize = 0 ; |
| if ( command == 1 ) |
| { |
| printf( "\n\r-I- Sending command " ) ; |
| for ( i=0 ; i < sizeof( testCommand1 ) ; i++ ) |
| { |
| printf( "0x%02X ", testCommand1[i] ) ; |
| } |
| printf( "...\n\r" ) ; |
| ucSize = ISO7816_XfrBlockTPDU_T0( testCommand1, pMessage, sizeof( testCommand1 ) ) ; |
| } |
| else |
| { |
| if ( command == 2 ) |
| { |
| printf( "\n\r-I- Sending command " ) ; |
| for ( i=0 ; i < sizeof( testCommand2 ) ; i++ ) |
| { |
| printf("0x%02X ", testCommand2[i] ) ; |
| } |
| printf( "...\n\r" ) ; |
| ucSize = ISO7816_XfrBlockTPDU_T0( testCommand2, pMessage, sizeof( testCommand2 ) ) ; |
| } |
| else |
| { |
| if ( command == 3 ) |
| { |
| printf( "\n\r-I- Sending command " ) ; |
| for ( i=0 ; i < sizeof( testCommand3 ) ; i++ ) |
| { |
| printf( "0x%02X ", testCommand3[i] ) ; |
| } |
| printf( "...\n\r" ) ; |
| ucSize = ISO7816_XfrBlockTPDU_T0( testCommand3, pMessage, sizeof( testCommand3 ) ) ; |
| } |
| else |
| { |
| if ( command == 4 ) |
| { |
| printf( "\n\r-I- Sending command " ) ; |
| for ( i=0 ; i < sizeof( testCommand4 ) ; i++ ) |
| { |
| printf( "0x%02X ", testCommand4[i] ) ; |
| } |
| printf( "...\n\r" ) ; |
| ucSize = ISO7816_XfrBlockTPDU_T0( testCommand4, pMessage, sizeof( testCommand4 ) ) ; |
| } |
| } |
| } |
| } |
| |
| /* Output smartcard answer */ |
| if ( ucSize > 0 ) |
| { |
| printf( "\n\rAnswer: " ) ; |
| for ( i=0 ; i < ucSize ; i++ ) |
| { |
| printf( "0x%02X ", pMessage[i] ) ; |
| } |
| printf( "\n\r" ) ; |
| } |
| } |
| |
| printf( "Quitting ...\n\r" ) ; |
| } |
| |
| /*------------------------------------------------------------------------------ |
| * Exported functions |
| *------------------------------------------------------------------------------*/ |
| |
| /** |
| * Initializes the DBGU and ISO7816 driver, and starts some tests. |
| * \return Unused (ANSI-C compatibility) |
| */ |
| extern int main( void ) |
| { |
| uint8_t pAtr[MAX_ATR_SIZE] ; |
| uint8_t ucSize ; |
| |
| LED_Configure(LED_NUM_GREEN); |
| LED_Set(LED_NUM_GREEN); |
| |
| /* Disable watchdog*/ |
| WDT_Disable( WDT ) ; |
| |
| /* Initialize Atr buffer */ |
| memset( pAtr, 0, sizeof( pAtr ) ) ; |
| |
| printf( "-- USART ISO7816 Example %s --\n\r", SOFTPACK_VERSION ) ; |
| printf( "-- %s\n\r", BOARD_NAME ) ; |
| printf( "-- Compiled: %s %s --\n\r", __DATE__, __TIME__ ) ; |
| |
| /* Configure IT on Smart Card */ |
| ConfigureCardDetection() ; |
| |
| /* Configure ISO7816 driver */ |
| PIO_Configure( pinsISO7816, PIO_LISTSIZE( pinsISO7816 ) ) ; |
| |
| // FIXME: RST seems to be allways low here |
| printf("******* Reset State1 (1 if the Pin RstMC is high): 0x%X\n\r", ISO7816_StatusReset()); |
| |
| ISO7816_Init( pinIso7816RstMC ) ; |
| |
| printf("******* Reset State2 (1 if the Pin RstMC is high): 0x%X\n\r", ISO7816_StatusReset()); |
| |
| /* Read ATR */ |
| ISO7816_warm_reset() ; |
| |
| ISO7816_Datablock_ATR( pAtr, &ucSize ) ; |
| printf("******* Reset State3 (1 if the Pin RstMC is high): 0x%X\n\r", ISO7816_StatusReset()); |
| |
| /* Decode ATR */ |
| ISO7816_Decode_ATR( pAtr ) ; |
| |
| // FIXME: RST seems to be allways high |
| printf("******* Reset State4 (1 if the Pin RstMC is high): 0x%X\n\r", ISO7816_StatusReset()); |
| |
| /* Allow user to send some commands */ |
| SendReceiveCommands() ; |
| |
| return 0 ; |
| } |
| |