| <vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'> |
| <node id='21'> |
| <child_of nodeid='4' /> |
| <name>SGSN Configuration Node</name> |
| <description>Configure the remote GGSN, access-control and other |
| attributes of the SGSN</description> |
| <command id='gtp local-ip A.B.C.D'> |
| <description> |
| Configure the local IP address to which the SGSN should |
| bind for the Gp interface (towards the GGSNs). |
| |
| Please note that in case you would like to run the GGSN |
| on the same machine as the SGSN, you can not run both on |
| the same IP address. It is suggested to use 127.0.0.1 |
| for the SGSN and 127.0.0.2 for the GGSN in such |
| situations. |
| </description> |
| </command> |
| <command id='ggsn <0-255> remote-ip A.B.C.D'> |
| <description> |
| Configure a static GGSN with a given numeric identifier |
| to use the specified remote IP address. |
| </description> |
| </command> |
| <command id='ggsn <0-255> gtp-version (0|1)'> |
| <description> |
| Configure whether to use GTPv0 or GTPv1 towards the |
| specified GSSN number. |
| </description> |
| </command> |
| <command id='ggsn dynamic'> |
| <description> |
| Enable dynamic resolving of GGSNs based on DNS resolving |
| the APN name like in a GRX-style setup. Changing this |
| setting requires a re-start of the SGSN. |
| </description> |
| </command> |
| <command id='grx-dns-add A.B.C.D'> |
| <description> |
| Use the specified IP address for DNS-resolving the AP |
| names to GGSN IP addresses |
| </description> |
| </command> |
| <command id='apn APNAME ggsn <0-255>'> |
| <description> |
| Map the given APN Name to the given GGSN number. |
| </description> |
| </command> |
| <command id='apn APNAME imsi-prefx IMSIPRE ggsn <0-255>'> |
| <description> |
| Map the given APN Name to the given GGSN number _only_ |
| if the IMSI matches the given prefix. |
| </description> |
| </command> |
| <command id='imsi-acl (add|del) IMSI'> |
| <description> |
| Add or delete the given IMSI to/from the global Access |
| Control List. |
| </description> |
| </command> |
| <command id='auth-policy (accept-all|closed|acl-only|remote)'> |
| <description> |
| Configure the Authorization policy of the SGSN. This |
| setting determines which subscribers are permitted to |
| register to the network. |
| </description> |
| </command> |
| <command id='gsup remote-ip A.B.C.D'> |
| <description> |
| Set the IP address of the HLR (gateway) for the GSUP protocol. |
| This setting only applies if auth-policy remote is used. |
| </description> |
| </command> |
| <command id='gsup oap-id <0-65535>'> |
| <description> |
| Set the OAP client ID for authentication on the GSUP |
| protocol. |
| This setting only applies if auth-policy remote is used. |
| </description> |
| </command> |
| <command id='gsup oap-k K'> |
| <description> |
| Set the OAP shared secret key K for authentication on |
| the GSUP protocol. |
| This setting only applies if auth-policy remote is used. |
| </description> |
| </command> |
| <command id='gsup oap-opc OPC'> |
| <description> |
| Set the OAP shared secret OPC for authentication on the |
| GSUP protocol. |
| This setting only applies if auth-policy remote is used. |
| </description> |
| </command> |
| <command id='access-point-name NAME'> |
| <description> |
| Globally allow the given APN name for all subscribers. |
| </description> |
| </command> |
| <command id='cdr filename NAME'> |
| <description> |
| Set the file name for the call-data-record file, |
| logging the data usage of each subscriber. |
| </description> |
| </command> |
| <command id='cdr interval <1-2147483647>'> |
| <description> |
| Set the interval (in secodnds) for the call-data-record |
| file. |
| </description> |
| </command> |
| </node> |
| </vtydoc> |