| <vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'> |
| <node id='_common_cmds_'> |
| <name>Common Commands</name> |
| <description>These commands are available on all VTY nodes. They are listed here only once, to unclutter the VTY reference.</description> |
| <command id='help'> |
| <params> |
| <param name='help' doc='Description of the interactive help system' /> |
| </params> |
| </command> |
| <command id='list'> |
| <params> |
| <param name='list' doc='Print command list' /> |
| </params> |
| </command> |
| <command id='write terminal'> |
| <params> |
| <param name='write' doc='Write running configuration to memory, network, or terminal' /> |
| <param name='terminal' doc='Write to terminal' /> |
| </params> |
| </command> |
| <command id='write file'> |
| <params> |
| <param name='write' doc='Write running configuration to memory, network, or terminal' /> |
| <param name='file' doc='Write to configuration file' /> |
| </params> |
| </command> |
| <command id='write memory'> |
| <params> |
| <param name='write' doc='Write running configuration to memory, network, or terminal' /> |
| <param name='memory' doc='Write configuration to the file (same as write file)' /> |
| </params> |
| </command> |
| <command id='write'> |
| <params> |
| <param name='write' doc='Write running configuration to memory, network, or terminal' /> |
| </params> |
| </command> |
| <command id='show running-config'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='running-config' doc='running configuration' /> |
| </params> |
| </command> |
| <command id='exit'> |
| <params> |
| <param name='exit' doc='Exit current mode and down to previous mode' /> |
| </params> |
| </command> |
| <command id='end'> |
| <params> |
| <param name='end' doc='End current mode and change to enable mode.' /> |
| </params> |
| </command> |
| </node> |
| <node id='view'> |
| <name>view</name> |
| <command id='show version'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='version' doc='Displays program version' /> |
| </params> |
| </command> |
| <command id='show online-help'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='online-help' doc='Online help' /> |
| </params> |
| </command> |
| <command id='enable'> |
| <params> |
| <param name='enable' doc='Turn on privileged mode command' /> |
| </params> |
| </command> |
| <command id='terminal length <0-512>'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='length' doc='Set number of lines on a screen' /> |
| <param name='<0-512>' doc='Number of lines on screen (0 for no pausing)' /> |
| </params> |
| </command> |
| <command id='terminal no length'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='length' doc='Set number of lines on a screen' /> |
| </params> |
| </command> |
| <command id='who'> |
| <params> |
| <param name='who' doc='Display who is on vty' /> |
| </params> |
| </command> |
| <command id='show history'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='history' doc='Display the session command history' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> users'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='users' doc='User Table' /> |
| </params> |
| </command> |
| <command id='show cs7 (sua|m3ua|ipa) [<0-65534>]'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='sua' doc='SCCP User Adaptation' /> |
| <param name='m3ua' doc='MTP3 User Adaptation' /> |
| <param name='ipa' doc='IPA Multiplex (SCCP Lite)' /> |
| <param name='[<0-65534>]' doc='Port Number' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> asp'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='asp' doc='Application Server Process (ASP)' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> as (active|all|m3ua|sua)'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='as' doc='Application Server (AS)' /> |
| <param name='active' doc='Display all active ASs' /> |
| <param name='all' doc='Display all ASs (default)' /> |
| <param name='m3ua' doc='Display all m3ua ASs' /> |
| <param name='sua' doc='Display all SUA ASs' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp addressbook'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='addressbook' doc='List all SCCP addressbook entries' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp users'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='users' doc='Show List of SCCP Users registered' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp ssn <0-65535>'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='ssn' doc='Find an SCCP User registered for the given SSN' /> |
| <param name='<0-65535>' doc='Subsystem Number (SSN)' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp connections'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='connections' doc='Show List of active SCCP connections' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp timers'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signaling Connection Control Part' /> |
| <param name='timers' doc='Show List of SCCP timers' /> |
| </params> |
| </command> |
| <command id='show cnlink'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cnlink' doc='Display information on core network link' /> |
| </params> |
| </command> |
| <command id='show hnb all'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='hnb' doc='Display information about all HNB' /> |
| <param name='all' doc='(null)' /> |
| </params> |
| </command> |
| <command id='show hnb NAME '> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='hnb' doc='Display information about a HNB' /> |
| <param name='NAME' doc='(null)' /> |
| </params> |
| </command> |
| <command id='show ue all'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='ue' doc='Display information about a UE' /> |
| <param name='all' doc='(null)' /> |
| </params> |
| </command> |
| <command id='show talloc'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='talloc' doc='Display talloc info' /> |
| </params> |
| </command> |
| <command id='logging enable'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='enable' doc='Enables logging to this vty' /> |
| </params> |
| </command> |
| <command id='logging disable'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='disable' doc='Disables logging to this vty' /> |
| </params> |
| </command> |
| <command id='logging filter all (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='filter' doc='Filter log messages' /> |
| <param name='all' doc='Do you want to log all messages?' /> |
| <param name='0' doc='Only print messages matched by other filters' /> |
| <param name='1' doc='Bypass filter and print all messages' /> |
| </params> |
| </command> |
| <command id='logging color (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='color' doc='Configure color-printing for log messages' /> |
| <param name='0' doc='Don't use color for printing messages' /> |
| <param name='1' doc='Use color for printing messages' /> |
| </params> |
| </command> |
| <command id='logging timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp' /> |
| </params> |
| </command> |
| <command id='logging print extended-timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='extended-timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' /> |
| </params> |
| </command> |
| <command id='logging print category (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem name' /> |
| </params> |
| </command> |
| <command id='logging print category-hex (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category-hex' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem nr in hex ('<000b>')' /> |
| </params> |
| </command> |
| <command id='logging print level (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='level' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the log level name' /> |
| </params> |
| </command> |
| <command id='logging print file (0|1|basename) [last]'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='file' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the source file and line' /> |
| <param name='basename' doc='Prefix each log message with the source file's basename (strip leading paths) and line' /> |
| <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' /> |
| </params> |
| </command> |
| <command id='logging set-log-mask MASK'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='set-log-mask' doc='Set the logmask of this logging target' /> |
| <param name='MASK' doc='List of logging categories to log, e.g. 'abc:mno:xyz'. Available log categories depend on the specific application, refer to the 'logging level' command. Optionally add individual log levels like 'abc,1:mno,3:xyz,5', where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' /> |
| </params> |
| </command> |
| <command id='logging level (main|hnbap|rua|ranap|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='main' doc='Main program' /> |
| <param name='hnbap' doc='Home Node B Application Part' /> |
| <param name='rua' doc='RANAP User Adaptation' /> |
| <param name='ranap' doc='RAN Application Part' /> |
| <param name='lglobal' doc='Library-internal global log family' /> |
| <param name='llapd' doc='LAPD in libosmogsm' /> |
| <param name='linp' doc='A-bis Intput Subsystem' /> |
| <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' /> |
| <param name='lmi' doc='A-bis Input Driver for Signalling' /> |
| <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' /> |
| <param name='lsms' doc='Layer3 Short Message Service (SMS)' /> |
| <param name='lctrl' doc='Control Interface' /> |
| <param name='lgtp' doc='GPRS GTP library' /> |
| <param name='lstats' doc='Statistics messages and logging' /> |
| <param name='lgsup' doc='Generic Subscriber Update Protocol' /> |
| <param name='loap' doc='Osmocom Authentication Protocol' /> |
| <param name='lss7' doc='libosmo-sigtran Signalling System 7' /> |
| <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' /> |
| <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' /> |
| <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' /> |
| <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' /> |
| <param name='ljibuf' doc='libosmo-netif Jitter Buffer' /> |
| <param name='lrspro' doc='Remote SIM protocol' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level set-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level force-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the 'no logging level force-all' command. Note: any 'logging level <category> <level>' commands will have no visible effect after this, until the forced level is released.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='no logging level force-all'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Release any globally forced log level set with 'logging level force-all <level>'' /> |
| </params> |
| </command> |
| <command id='show logging vty'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='logging' doc='Show current logging configuration' /> |
| <param name='vty' doc='Show current logging configuration for this vty' /> |
| </params> |
| </command> |
| <command id='show alarms'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='alarms' doc='Show current logging configuration' /> |
| </params> |
| </command> |
| </node> |
| <node id='enable'> |
| <name>enable</name> |
| <command id='disable'> |
| <params> |
| <param name='disable' doc='Turn off privileged mode command' /> |
| </params> |
| </command> |
| <command id='configure terminal'> |
| <params> |
| <param name='configure' doc='Configuration from vty interface' /> |
| <param name='terminal' doc='Configuration terminal' /> |
| </params> |
| </command> |
| <command id='copy running-config startup-config'> |
| <params> |
| <param name='copy' doc='Copy configuration' /> |
| <param name='running-config' doc='Copy running config to... ' /> |
| <param name='startup-config' doc='Copy running config to startup config (same as write file)' /> |
| </params> |
| </command> |
| <command id='show startup-config'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='startup-config' doc='Contentes of startup configuration' /> |
| </params> |
| </command> |
| <command id='show version'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='version' doc='Displays program version' /> |
| </params> |
| </command> |
| <command id='show online-help'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='online-help' doc='Online help' /> |
| </params> |
| </command> |
| <command id='terminal length <0-512>'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='length' doc='Set number of lines on a screen' /> |
| <param name='<0-512>' doc='Number of lines on screen (0 for no pausing)' /> |
| </params> |
| </command> |
| <command id='terminal no length'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='length' doc='Set number of lines on a screen' /> |
| </params> |
| </command> |
| <command id='who'> |
| <params> |
| <param name='who' doc='Display who is on vty' /> |
| </params> |
| </command> |
| <command id='show history'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='history' doc='Display the session command history' /> |
| </params> |
| </command> |
| <command id='terminal monitor'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='monitor' doc='Copy debug output to the current terminal line' /> |
| </params> |
| </command> |
| <command id='terminal no monitor'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='monitor' doc='Copy debug output to the current terminal line' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> users'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='users' doc='User Table' /> |
| </params> |
| </command> |
| <command id='show cs7 (sua|m3ua|ipa) [<0-65534>]'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='sua' doc='SCCP User Adaptation' /> |
| <param name='m3ua' doc='MTP3 User Adaptation' /> |
| <param name='ipa' doc='IPA Multiplex (SCCP Lite)' /> |
| <param name='[<0-65534>]' doc='Port Number' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> asp'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='asp' doc='Application Server Process (ASP)' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> as (active|all|m3ua|sua)'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='as' doc='Application Server (AS)' /> |
| <param name='active' doc='Display all active ASs' /> |
| <param name='all' doc='Display all ASs (default)' /> |
| <param name='m3ua' doc='Display all m3ua ASs' /> |
| <param name='sua' doc='Display all SUA ASs' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp addressbook'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='addressbook' doc='List all SCCP addressbook entries' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp users'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='users' doc='Show List of SCCP Users registered' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp ssn <0-65535>'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='ssn' doc='Find an SCCP User registered for the given SSN' /> |
| <param name='<0-65535>' doc='Subsystem Number (SSN)' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp connections'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='connections' doc='Show List of active SCCP connections' /> |
| </params> |
| </command> |
| <command id='show cs7 instance <0-15> sccp timers'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='An instance of the SS7 stack' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| <param name='sccp' doc='Signaling Connection Control Part' /> |
| <param name='timers' doc='Show List of SCCP timers' /> |
| </params> |
| </command> |
| <command id='show cnlink'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='cnlink' doc='Display information on core network link' /> |
| </params> |
| </command> |
| <command id='show hnb all'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='hnb' doc='Display information about all HNB' /> |
| <param name='all' doc='(null)' /> |
| </params> |
| </command> |
| <command id='show hnb NAME '> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='hnb' doc='Display information about a HNB' /> |
| <param name='NAME' doc='(null)' /> |
| </params> |
| </command> |
| <command id='show ue all'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='ue' doc='Display information about a UE' /> |
| <param name='all' doc='(null)' /> |
| </params> |
| </command> |
| <command id='show talloc'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='talloc' doc='Display talloc info' /> |
| </params> |
| </command> |
| <command id='logging enable'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='enable' doc='Enables logging to this vty' /> |
| </params> |
| </command> |
| <command id='logging disable'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='disable' doc='Disables logging to this vty' /> |
| </params> |
| </command> |
| <command id='logging filter all (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='filter' doc='Filter log messages' /> |
| <param name='all' doc='Do you want to log all messages?' /> |
| <param name='0' doc='Only print messages matched by other filters' /> |
| <param name='1' doc='Bypass filter and print all messages' /> |
| </params> |
| </command> |
| <command id='logging color (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='color' doc='Configure color-printing for log messages' /> |
| <param name='0' doc='Don't use color for printing messages' /> |
| <param name='1' doc='Use color for printing messages' /> |
| </params> |
| </command> |
| <command id='logging timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp' /> |
| </params> |
| </command> |
| <command id='logging print extended-timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='extended-timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' /> |
| </params> |
| </command> |
| <command id='logging print category (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem name' /> |
| </params> |
| </command> |
| <command id='logging print category-hex (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category-hex' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem nr in hex ('<000b>')' /> |
| </params> |
| </command> |
| <command id='logging print level (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='level' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the log level name' /> |
| </params> |
| </command> |
| <command id='logging print file (0|1|basename) [last]'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='file' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the source file and line' /> |
| <param name='basename' doc='Prefix each log message with the source file's basename (strip leading paths) and line' /> |
| <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' /> |
| </params> |
| </command> |
| <command id='logging set-log-mask MASK'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='set-log-mask' doc='Set the logmask of this logging target' /> |
| <param name='MASK' doc='List of logging categories to log, e.g. 'abc:mno:xyz'. Available log categories depend on the specific application, refer to the 'logging level' command. Optionally add individual log levels like 'abc,1:mno,3:xyz,5', where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' /> |
| </params> |
| </command> |
| <command id='logging level (main|hnbap|rua|ranap|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='main' doc='Main program' /> |
| <param name='hnbap' doc='Home Node B Application Part' /> |
| <param name='rua' doc='RANAP User Adaptation' /> |
| <param name='ranap' doc='RAN Application Part' /> |
| <param name='lglobal' doc='Library-internal global log family' /> |
| <param name='llapd' doc='LAPD in libosmogsm' /> |
| <param name='linp' doc='A-bis Intput Subsystem' /> |
| <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' /> |
| <param name='lmi' doc='A-bis Input Driver for Signalling' /> |
| <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' /> |
| <param name='lsms' doc='Layer3 Short Message Service (SMS)' /> |
| <param name='lctrl' doc='Control Interface' /> |
| <param name='lgtp' doc='GPRS GTP library' /> |
| <param name='lstats' doc='Statistics messages and logging' /> |
| <param name='lgsup' doc='Generic Subscriber Update Protocol' /> |
| <param name='loap' doc='Osmocom Authentication Protocol' /> |
| <param name='lss7' doc='libosmo-sigtran Signalling System 7' /> |
| <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' /> |
| <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' /> |
| <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' /> |
| <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' /> |
| <param name='ljibuf' doc='libosmo-netif Jitter Buffer' /> |
| <param name='lrspro' doc='Remote SIM protocol' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level set-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level force-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the 'no logging level force-all' command. Note: any 'logging level <category> <level>' commands will have no visible effect after this, until the forced level is released.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='no logging level force-all'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Release any globally forced log level set with 'logging level force-all <level>'' /> |
| </params> |
| </command> |
| <command id='show logging vty'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='logging' doc='Show current logging configuration' /> |
| <param name='vty' doc='Show current logging configuration for this vty' /> |
| </params> |
| </command> |
| <command id='show alarms'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='alarms' doc='Show current logging configuration' /> |
| </params> |
| </command> |
| </node> |
| <node id='config'> |
| <name>config</name> |
| <command id='hostname WORD'> |
| <params> |
| <param name='hostname' doc='Set system's network name' /> |
| <param name='WORD' doc='This system's network name' /> |
| </params> |
| </command> |
| <command id='no hostname [HOSTNAME]'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='hostname' doc='Reset system's network name' /> |
| <param name='[HOSTNAME]' doc='Host name of this router' /> |
| </params> |
| </command> |
| <command id='password (8|) WORD'> |
| <params> |
| <param name='password' doc='Assign the terminal connection password' /> |
| <param name='8' doc='Specifies a HIDDEN password will follow' /> |
| <param name='' doc='dummy string ' /> |
| <param name='WORD' doc='The HIDDEN line password string' /> |
| </params> |
| </command> |
| <command id='password LINE'> |
| <params> |
| <param name='password' doc='Assign the terminal connection password' /> |
| <param name='LINE' doc='The UNENCRYPTED (cleartext) line password' /> |
| </params> |
| </command> |
| <command id='enable password (8|) WORD'> |
| <params> |
| <param name='enable' doc='Modify enable password parameters' /> |
| <param name='password' doc='Assign the privileged level password' /> |
| <param name='8' doc='Specifies a HIDDEN password will follow' /> |
| <param name='' doc='dummy string ' /> |
| <param name='WORD' doc='The HIDDEN 'enable' password string' /> |
| </params> |
| </command> |
| <command id='enable password LINE'> |
| <params> |
| <param name='enable' doc='Modify enable password parameters' /> |
| <param name='password' doc='Assign the privileged level password' /> |
| <param name='LINE' doc='The UNENCRYPTED (cleartext) 'enable' password' /> |
| </params> |
| </command> |
| <command id='no enable password'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='enable' doc='Modify enable password parameters' /> |
| <param name='password' doc='Assign the privileged level password' /> |
| </params> |
| </command> |
| <command id='banner motd default'> |
| <params> |
| <param name='banner' doc='Set banner string' /> |
| <param name='motd' doc='Strings for motd' /> |
| <param name='default' doc='Default string' /> |
| </params> |
| </command> |
| <command id='banner motd file [FILE]'> |
| <params> |
| <param name='banner' doc='Set banner' /> |
| <param name='motd' doc='Banner for motd' /> |
| <param name='file' doc='Banner from a file' /> |
| <param name='[FILE]' doc='Filename' /> |
| </params> |
| </command> |
| <command id='no banner motd'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='banner' doc='Set banner string' /> |
| <param name='motd' doc='Strings for motd' /> |
| </params> |
| </command> |
| <command id='service terminal-length <0-512>'> |
| <params> |
| <param name='service' doc='Set up miscellaneous service' /> |
| <param name='terminal-length' doc='System wide terminal length configuration' /> |
| <param name='<0-512>' doc='Number of lines of VTY (0 means no line control)' /> |
| </params> |
| </command> |
| <command id='no service terminal-length [<0-512>]'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='service' doc='Set up miscellaneous service' /> |
| <param name='terminal-length' doc='System wide terminal length configuration' /> |
| <param name='[<0-512>]' doc='Number of lines of VTY (0 means no line control)' /> |
| </params> |
| </command> |
| <command id='line vty'> |
| <params> |
| <param name='line' doc='Configure a terminal line' /> |
| <param name='vty' doc='Virtual terminal' /> |
| </params> |
| </command> |
| <command id='service advanced-vty'> |
| <params> |
| <param name='service' doc='Set up miscellaneous service' /> |
| <param name='advanced-vty' doc='Enable advanced mode vty interface' /> |
| </params> |
| </command> |
| <command id='no service advanced-vty'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='service' doc='Set up miscellaneous service' /> |
| <param name='advanced-vty' doc='Enable advanced mode vty interface' /> |
| </params> |
| </command> |
| <command id='show history'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='history' doc='Display the session command history' /> |
| </params> |
| </command> |
| <command id='cs7 instance <0-15>'> |
| <params> |
| <param name='cs7' doc='ITU-T Signaling System 7' /> |
| <param name='instance' doc='Configure a SS7 Instance' /> |
| <param name='<0-15>' doc='An instance of the SS7 stack' /> |
| </params> |
| </command> |
| <command id='hnbgw'> |
| <params> |
| <param name='hnbgw' doc='Configure HNBGW options' /> |
| </params> |
| </command> |
| <command id='log stderr'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='stderr' doc='Logging via STDERR of the process' /> |
| </params> |
| </command> |
| <command id='no log stderr'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='stderr' doc='Logging via STDERR of the process' /> |
| </params> |
| </command> |
| <command id='log file .FILENAME'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='file' doc='Logging to text file' /> |
| <param name='.FILENAME' doc='Filename' /> |
| </params> |
| </command> |
| <command id='no log file .FILENAME'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='file' doc='Logging to text file' /> |
| <param name='.FILENAME' doc='Filename' /> |
| </params> |
| </command> |
| <command id='log alarms <2-32700>'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='alarms' doc='Logging alarms to osmo_strrb' /> |
| <param name='<2-32700>' doc='Maximum number of messages to log' /> |
| </params> |
| </command> |
| <command id='no log alarms'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='alarms' doc='Logging alarms to osmo_strrb' /> |
| </params> |
| </command> |
| <command id='log syslog (authpriv|cron|daemon|ftp|lpr|mail|news|user|uucp)'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='syslog' doc='Logging via syslog' /> |
| <param name='authpriv' doc='Security/authorization messages facility' /> |
| <param name='cron' doc='Clock daemon (cron/at) facility' /> |
| <param name='daemon' doc='General system daemon facility' /> |
| <param name='ftp' doc='Ftp daemon facility' /> |
| <param name='lpr' doc='Line printer facility' /> |
| <param name='mail' doc='Mail facility' /> |
| <param name='news' doc='News facility' /> |
| <param name='user' doc='Generic facility' /> |
| <param name='uucp' doc='UUCP facility' /> |
| </params> |
| </command> |
| <command id='log syslog local <0-7>'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='syslog' doc='Logging via syslog' /> |
| <param name='local' doc='Syslog LOCAL facility' /> |
| <param name='<0-7>' doc='Local facility number' /> |
| </params> |
| </command> |
| <command id='no log syslog'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='syslog' doc='Logging via syslog' /> |
| </params> |
| </command> |
| <command id='log gsmtap [HOSTNAME]'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='gsmtap' doc='Logging via GSMTAP' /> |
| <param name='[HOSTNAME]' doc='Host name to send the GSMTAP logging to (UDP port 4729)' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-log'> |
| <name>config-log</name> |
| <command id='logging filter all (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='filter' doc='Filter log messages' /> |
| <param name='all' doc='Do you want to log all messages?' /> |
| <param name='0' doc='Only print messages matched by other filters' /> |
| <param name='1' doc='Bypass filter and print all messages' /> |
| </params> |
| </command> |
| <command id='logging color (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='color' doc='Configure color-printing for log messages' /> |
| <param name='0' doc='Don't use color for printing messages' /> |
| <param name='1' doc='Use color for printing messages' /> |
| </params> |
| </command> |
| <command id='logging timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp' /> |
| </params> |
| </command> |
| <command id='logging print extended-timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='extended-timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' /> |
| </params> |
| </command> |
| <command id='logging print category (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem name' /> |
| </params> |
| </command> |
| <command id='logging print category-hex (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category-hex' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem nr in hex ('<000b>')' /> |
| </params> |
| </command> |
| <command id='logging print level (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='level' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the log level name' /> |
| </params> |
| </command> |
| <command id='logging print file (0|1|basename) [last]'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='file' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the source file and line' /> |
| <param name='basename' doc='Prefix each log message with the source file's basename (strip leading paths) and line' /> |
| <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' /> |
| </params> |
| </command> |
| <command id='logging level (main|hnbap|rua|ranap|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='main' doc='Main program' /> |
| <param name='hnbap' doc='Home Node B Application Part' /> |
| <param name='rua' doc='RANAP User Adaptation' /> |
| <param name='ranap' doc='RAN Application Part' /> |
| <param name='lglobal' doc='Library-internal global log family' /> |
| <param name='llapd' doc='LAPD in libosmogsm' /> |
| <param name='linp' doc='A-bis Intput Subsystem' /> |
| <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' /> |
| <param name='lmi' doc='A-bis Input Driver for Signalling' /> |
| <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' /> |
| <param name='lsms' doc='Layer3 Short Message Service (SMS)' /> |
| <param name='lctrl' doc='Control Interface' /> |
| <param name='lgtp' doc='GPRS GTP library' /> |
| <param name='lstats' doc='Statistics messages and logging' /> |
| <param name='lgsup' doc='Generic Subscriber Update Protocol' /> |
| <param name='loap' doc='Osmocom Authentication Protocol' /> |
| <param name='lss7' doc='libosmo-sigtran Signalling System 7' /> |
| <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' /> |
| <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' /> |
| <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' /> |
| <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' /> |
| <param name='ljibuf' doc='libosmo-netif Jitter Buffer' /> |
| <param name='lrspro' doc='Remote SIM protocol' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level set-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level force-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the 'no logging level force-all' command. Note: any 'logging level <category> <level>' commands will have no visible effect after this, until the forced level is released.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='no logging level force-all'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Release any globally forced log level set with 'logging level force-all <level>'' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-line'> |
| <name>config-line</name> |
| <command id='login'> |
| <params> |
| <param name='login' doc='Enable password checking' /> |
| </params> |
| </command> |
| <command id='no login'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='login' doc='Enable password checking' /> |
| </params> |
| </command> |
| <command id='bind A.B.C.D [<0-65535>]'> |
| <params> |
| <param name='bind' doc='Accept VTY telnet connections on local interface' /> |
| <param name='A.B.C.D' doc='Local interface IP address (default: 127.0.0.1)' /> |
| <param name='[<0-65535>]' doc='Local TCP port number' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-cs7'> |
| <name>config-cs7</name> |
| <command id='description .TEXT'> |
| <params> |
| <param name='description' doc='Save human-readable description of the object' /> |
| <param name='.TEXT' doc='Text until the end of the line' /> |
| </params> |
| </command> |
| <command id='network-indicator (international | national | reserved | spare)'> |
| <params> |
| <param name='network-indicator' doc='Configure the Network Indicator' /> |
| <param name='international' doc='International Network' /> |
| <param name='national' doc='National Network' /> |
| <param name='reserved' doc='Reserved Network' /> |
| <param name='spare' doc='Spare Network' /> |
| </params> |
| </command> |
| <command id='point-code POINT_CODE'> |
| <params> |
| <param name='point-code' doc='Configure the local Point Code' /> |
| <param name='POINT_CODE' doc='Point Code' /> |
| </params> |
| </command> |
| <command id='point-code format <1-24> [<1-23>] [<1-22>]'> |
| <params> |
| <param name='point-code' doc='Point Code' /> |
| <param name='format' doc='Configure Point Code Format' /> |
| <param name='<1-24>' doc='Length of first PC component' /> |
| <param name='[<1-23>]' doc='Length of second PC component' /> |
| <param name='[<1-22>]' doc='Length of third PC component' /> |
| </params> |
| </command> |
| <command id='point-code format default'> |
| <params> |
| <param name='point-code' doc='Point Code' /> |
| <param name='format' doc='Configure Point Code Format' /> |
| <param name='default' doc='Default Point Code Format (3.8.3)' /> |
| </params> |
| </command> |
| <command id='point-code delimiter (default|dash)'> |
| <params> |
| <param name='point-code' doc='Point Code' /> |
| <param name='delimiter' doc='Configure Point Code Delimiter' /> |
| <param name='default' doc='Use dot as delimiter' /> |
| <param name='dash' doc='User dash as delimiter' /> |
| </params> |
| </command> |
| <command id='xua rkm routing-key-allocation (static-only|dynamic-permitted)'> |
| <params> |
| <param name='xua' doc='SIGTRAN xxxUA related' /> |
| <param name='rkm' doc='Routing Key Management' /> |
| <param name='routing-key-allocation' doc='Routing Key Management Allocation Policy' /> |
| <param name='static-only' doc='Only static (pre-confgured) Routing Keys permitted' /> |
| <param name='dynamic-permitted' doc='Dynamically allocate Routing Keys for what ASPs request' /> |
| </params> |
| </command> |
| <command id='asp NAME <0-65535> <0-65535> (sua|m3ua|ipa)'> |
| <params> |
| <param name='asp' doc='Configure Application Server Process' /> |
| <param name='NAME' doc='Name of ASP' /> |
| <param name='<0-65535>' doc='Remote SCTP port number' /> |
| <param name='<0-65535>' doc='Local SCTP port number' /> |
| <param name='sua' doc='SCCP User Adaptation' /> |
| <param name='m3ua' doc='MTP3 User Adaptation' /> |
| <param name='ipa' doc='IPA Multiplex (SCCP Lite)' /> |
| </params> |
| </command> |
| <command id='no asp NAME'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='asp' doc='Disable Application Server Process' /> |
| <param name='NAME' doc='Name of ASP' /> |
| </params> |
| </command> |
| <command id='as NAME (sua|m3ua|ipa)'> |
| <params> |
| <param name='as' doc='Configure an Application Server' /> |
| <param name='NAME' doc='Name of the Application Server' /> |
| <param name='sua' doc='SCCP User Adaptation' /> |
| <param name='m3ua' doc='MTP3 User Adaptation' /> |
| <param name='ipa' doc='IPA Multiplex (SCCP Lite)' /> |
| </params> |
| </command> |
| <command id='no as NAME'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='as' doc='Disable Application Server' /> |
| <param name='NAME' doc='Name of AS' /> |
| </params> |
| </command> |
| <command id='sccp-address NAME'> |
| <params> |
| <param name='sccp-address' doc='Create/Modify an SCCP addressbook entry' /> |
| <param name='NAME' doc='Name of the SCCP Address' /> |
| </params> |
| </command> |
| <command id='no sccp-address NAME'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='sccp-address' doc='Delete an SCCP addressbook entry' /> |
| <param name='NAME' doc='Name of the SCCP Address' /> |
| </params> |
| </command> |
| <command id='sccp-timer (conn_est|ias|iar|rel|repeat_rel|int|guard|reset|reassembly) <1-999999>'> |
| <params> |
| <param name='sccp-timer' doc='Configure SCCP timer values, see ITU-T Q.714' /> |
| <param name='conn_est' doc='Waiting for connection confirm message, 1 to 2 minutes (default: 60)' /> |
| <param name='ias' doc='Send keep-alive: on an idle connection, delay before sending an Idle Timer message, 5 to 10 minutes (default: 420)' /> |
| <param name='iar' doc='Receive keep-alive: on an idle connection, delay until considering a connection as stale, 11 to 21 minutes (default: 900)' /> |
| <param name='rel' doc='Waiting for release complete message, 10 to 20 seconds (default: 10)' /> |
| <param name='repeat_rel' doc='Waiting for release complete message; or to repeat sending released message after the initial expiry, 10 to 20 seconds (default: 10)' /> |
| <param name='int' doc='Waiting for release complete message; or to release connection resources, freeze the LRN and alert a maintenance function after the initial expiry, extending to 1 minute (default: 60)' /> |
| <param name='guard' doc='Waiting to resume normal procedure for temporary connection sections during the restart procedure, 23 to 25 minutes (default: 1380)' /> |
| <param name='reset' doc='Waiting to release temporary connection section or alert maintenance function after reset request message is sent, 10 to 20 seconds (default: 10)' /> |
| <param name='reassembly' doc='Waiting to receive all the segments of the remaining segments, single segmented message after receiving the first segment, 10 to 20 seconds (default: 10)' /> |
| <param name='<1-999999>' doc='Timer value, in seconds' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-cs7-as'> |
| <name>config-cs7-as</name> |
| <command id='description .TEXT'> |
| <params> |
| <param name='description' doc='Save human-readable description of the object' /> |
| <param name='.TEXT' doc='Text until the end of the line' /> |
| </params> |
| </command> |
| <command id='asp NAME'> |
| <params> |
| <param name='asp' doc='Specify that a given ASP is part of this AS' /> |
| <param name='NAME' doc='Name of ASP to be added to AS' /> |
| </params> |
| </command> |
| <command id='no asp NAME'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='asp' doc='Specify ASP to be removed from this AS' /> |
| <param name='NAME' doc='Name of ASP to be removed' /> |
| </params> |
| </command> |
| <command id='traffic-mode (broadcast | loadshare | roundrobin | override)'> |
| <params> |
| <param name='traffic-mode' doc='Specifies traffic mode of operation of the ASP within the AS' /> |
| <param name='broadcast' doc='Broadcast to all ASP within AS' /> |
| <param name='loadshare' doc='Share Load among all ASP within AS' /> |
| <param name='roundrobin' doc='Round-Robin between all ASP within AS' /> |
| <param name='override' doc='Override' /> |
| </params> |
| </command> |
| <command id='recovery-timeout <1-2000>'> |
| <params> |
| <param name='recovery-timeout' doc='Specifies the recovery timeout value in milliseconds' /> |
| <param name='<1-2000>' doc='Recovery Timeout in Milliseconds' /> |
| </params> |
| </command> |
| <command id='qos-class <0-255>'> |
| <params> |
| <param name='qos-class' doc='Specity QoS Class of AS' /> |
| <param name='<0-255>' doc='QoS Class of AS' /> |
| </params> |
| </command> |
| <command id='routing-key RCONTEXT DPC'> |
| <params> |
| <param name='routing-key' doc='Define a routing key' /> |
| <param name='RCONTEXT' doc='Routing context number' /> |
| <param name='DPC' doc='Destination Point Code' /> |
| </params> |
| </command> |
| <command id='routing-key RCONTEXT DPC si (aal2|bicc|b-isup|h248|isup|sat-isup|sccp|tup)'> |
| <params> |
| <param name='routing-key' doc='Define a routing key' /> |
| <param name='RCONTEXT' doc='Routing context number' /> |
| <param name='DPC' doc='Destination Point Code' /> |
| <param name='si' doc='Match on Service Indicator' /> |
| <param name='aal2' doc='ATM Adaption Layer 2' /> |
| <param name='bicc' doc='Bearer Independent Call Control' /> |
| <param name='b-isup' doc='Broadband ISDN User Part' /> |
| <param name='h248' doc='H.248' /> |
| <param name='isup' doc='ISDN User Part' /> |
| <param name='sat-isup' doc='Sattelite ISDN User Part' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='tup' doc='Telephony User Part' /> |
| </params> |
| </command> |
| <command id='routing-key RCONTEXT DPC ssn SSN'> |
| <params> |
| <param name='routing-key' doc='Define a routing key' /> |
| <param name='RCONTEXT' doc='Routing context number' /> |
| <param name='DPC' doc='Destination Point Code' /> |
| <param name='ssn' doc='Match on Sub-System Number' /> |
| <param name='SSN' doc='Sub-System Number to match on' /> |
| </params> |
| </command> |
| <command id='routing-key RCONTEXT DPC si (aal2|bicc|b-isup|h248|isup|sat-isup|sccp|tup) ssn SSN'> |
| <params> |
| <param name='routing-key' doc='Define a routing key' /> |
| <param name='RCONTEXT' doc='Routing context number' /> |
| <param name='DPC' doc='Destination Point Code' /> |
| <param name='si' doc='Match on Service Indicator' /> |
| <param name='aal2' doc='ATM Adaption Layer 2' /> |
| <param name='bicc' doc='Bearer Independent Call Control' /> |
| <param name='b-isup' doc='Broadband ISDN User Part' /> |
| <param name='h248' doc='H.248' /> |
| <param name='isup' doc='ISDN User Part' /> |
| <param name='sat-isup' doc='Sattelite ISDN User Part' /> |
| <param name='sccp' doc='Signalling Connection Control Part' /> |
| <param name='tup' doc='Telephony User Part' /> |
| <param name='ssn' doc='Match on Sub-System Number' /> |
| <param name='SSN' doc='Sub-System Number to match on' /> |
| </params> |
| </command> |
| <command id='point-code override dpc PC'> |
| <params> |
| <param name='point-code' doc='Point Code Specific Features' /> |
| <param name='override' doc='Override (force) a point-code to hard-coded value' /> |
| <param name='dpc' doc='Override Source Point Code' /> |
| <param name='PC' doc='Override Destination Point Code' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-cs7-asp'> |
| <name>config-cs7-asp</name> |
| <command id='description .TEXT'> |
| <params> |
| <param name='description' doc='Save human-readable description of the object' /> |
| <param name='.TEXT' doc='Text until the end of the line' /> |
| </params> |
| </command> |
| <command id='remote-ip A.B.C.D'> |
| <params> |
| <param name='remote-ip' doc='Specify Remote IP Address of ASP' /> |
| <param name='A.B.C.D' doc='Remote IP Address of ASP' /> |
| </params> |
| </command> |
| <command id='local-ip A.B.C.D'> |
| <params> |
| <param name='local-ip' doc='Specify Local IP Address from which to contact ASP' /> |
| <param name='A.B.C.D' doc='Local IP Address from which to contact of ASP' /> |
| </params> |
| </command> |
| <command id='qos-class <0-255>'> |
| <params> |
| <param name='qos-class' doc='Specify QoS Class of ASP' /> |
| <param name='<0-255>' doc='QoS Class of ASP' /> |
| </params> |
| </command> |
| <command id='block'> |
| <params> |
| <param name='block' doc='Allows a SCTP Association with ASP, but doesn't let it become active' /> |
| </params> |
| </command> |
| <command id='shutdown'> |
| <params> |
| <param name='shutdown' doc='Terminates SCTP association; New associations will be rejected' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-cs7-sccpaddr'> |
| <name>config-cs7-sccpaddr</name> |
| <command id='no point-code'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='point-code' doc='Remove point-code Number' /> |
| </params> |
| </command> |
| <command id='no subsystem-number'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='subsystem-number' doc='Remove Subsystem Number' /> |
| </params> |
| </command> |
| <command id='no global-title'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='global-title' doc='Remove Global Title' /> |
| </params> |
| </command> |
| <command id='routing-indicator (GT|PC|IP)'> |
| <params> |
| <param name='routing-indicator' doc='Add Routing Indicator' /> |
| <param name='GT' doc='by global-title' /> |
| <param name='PC' doc='by point-code' /> |
| <param name='IP' doc='by ip-address' /> |
| </params> |
| </command> |
| <command id='point-code POINT_CODE'> |
| <params> |
| <param name='point-code' doc='Add point-code Number' /> |
| <param name='POINT_CODE' doc='PC' /> |
| </params> |
| </command> |
| <command id='subsystem-number <0-4294967295>'> |
| <params> |
| <param name='subsystem-number' doc='Add Subsystem Number' /> |
| <param name='<0-4294967295>' doc='SSN' /> |
| </params> |
| </command> |
| <command id='global-title'> |
| <params> |
| <param name='global-title' doc='Add/Modify Global Title' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-cs7-sccpaddr-gt'> |
| <name>config-cs7-sccpaddr-gt</name> |
| <command id='global-title-indicator <0-15>'> |
| <params> |
| <param name='global-title-indicator' doc='Set Global Title Indicator' /> |
| <param name='<0-15>' doc='GTI' /> |
| </params> |
| </command> |
| <command id='translation-type <0-255>'> |
| <params> |
| <param name='translation-type' doc='Set Global Title Translation Type' /> |
| <param name='<0-255>' doc='TT' /> |
| </params> |
| </command> |
| <command id='numbering-plan-indicator <0-15>'> |
| <params> |
| <param name='numbering-plan-indicator' doc='Set Global Title Numbering Plan Indicator' /> |
| <param name='<0-15>' doc='NPI' /> |
| </params> |
| </command> |
| <command id='nature-of-address-indicator <0-127>'> |
| <params> |
| <param name='nature-of-address-indicator' doc='Set Global Title Nature of Address Indicator' /> |
| <param name='<0-127>' doc='NAI' /> |
| </params> |
| </command> |
| <command id='digits DIGITS'> |
| <params> |
| <param name='digits' doc='Set Global Title Digits' /> |
| <param name='DIGITS' doc='Number digits' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-hnbgw'> |
| <name>config-hnbgw</name> |
| <command id='rnc-id <0-65535>'> |
| <params> |
| <param name='rnc-id' doc='Configure the HNBGW's RNC Id, the common RNC Id used for all connected hNodeB. It is sent to each hNodeB upon HNBAP HNB-Register-Accept, and the hNodeB will subsequently send this as RANAP InitialUE Messages' GlobalRNC-ID IE. Takes effect as soon as the hNodeB re-registers.' /> |
| <param name='<0-65535>' doc='RNC Id value' /> |
| </params> |
| </command> |
| <command id='iuh'> |
| <params> |
| <param name='iuh' doc='Configure Iuh options' /> |
| </params> |
| </command> |
| <command id='iucs'> |
| <params> |
| <param name='iucs' doc='Configure IuCS options' /> |
| </params> |
| </command> |
| <command id='iups'> |
| <params> |
| <param name='iups' doc='Configure IuPS options' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-hnbgw-iuh'> |
| <name>config-hnbgw-iuh</name> |
| <command id='local-ip A.B.C.D'> |
| <params> |
| <param name='local-ip' doc='Accept Iuh connections on local interface' /> |
| <param name='A.B.C.D' doc='Local interface IP address (default: 0.0.0.0)' /> |
| </params> |
| </command> |
| <command id='local-port <1-65535>'> |
| <params> |
| <param name='local-port' doc='Accept Iuh connections on local port' /> |
| <param name='<1-65535>' doc='Local interface port (default: 29169)' /> |
| </params> |
| </command> |
| <command id='hnbap-allow-tmsi (0|1)'> |
| <params> |
| <param name='hnbap-allow-tmsi' doc='Allow HNBAP UE Register messages with TMSI or PTMSI identity' /> |
| <param name='0' doc='Only accept IMSI identity, reject TMSI or PTMSI' /> |
| <param name='1' doc='Accept IMSI, TMSI or PTMSI as UE identity' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-hnbgw-iucs'> |
| <name>config-hnbgw-iucs</name> |
| <command id='remote-addr NAME'> |
| <params> |
| <param name='remote-addr' doc='SCCP address to send IuCS to (MSC)' /> |
| <param name='NAME' doc='SCCP address book entry name (see 'cs7-instance')' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-hnbgw-iups'> |
| <name>config-hnbgw-iups</name> |
| <command id='remote-addr NAME'> |
| <params> |
| <param name='remote-addr' doc='SCCP address to send IuPS to (SGSN)' /> |
| <param name='NAME' doc='SCCP address book entry name (see 'cs7-instance')' /> |
| </params> |
| </command> |
| </node> |
| </vtydoc> |