| <vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'> |
| <node id='_common_cmds_'> |
| <name>Common Commands</name> |
| <description>These commands are available on all VTY nodes. They are listed here only once, to unclutter the VTY reference.</description> |
| <command id='help'> |
| <params> |
| <param name='help' doc='Description of the interactive help system' /> |
| </params> |
| </command> |
| <command id='list'> |
| <params> |
| <param name='list' doc='Print command list' /> |
| </params> |
| </command> |
| <command id='write terminal'> |
| <params> |
| <param name='write' doc='Write running configuration to memory, network, or terminal' /> |
| <param name='terminal' doc='Write to terminal' /> |
| </params> |
| </command> |
| <command id='write file'> |
| <params> |
| <param name='write' doc='Write running configuration to memory, network, or terminal' /> |
| <param name='file' doc='Write to configuration file' /> |
| </params> |
| </command> |
| <command id='write memory'> |
| <params> |
| <param name='write' doc='Write running configuration to memory, network, or terminal' /> |
| <param name='memory' doc='Write configuration to the file (same as write file)' /> |
| </params> |
| </command> |
| <command id='write'> |
| <params> |
| <param name='write' doc='Write running configuration to memory, network, or terminal' /> |
| </params> |
| </command> |
| <command id='show running-config'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='running-config' doc='running configuration' /> |
| </params> |
| </command> |
| <command id='exit'> |
| <params> |
| <param name='exit' doc='Exit current mode and down to previous mode' /> |
| </params> |
| </command> |
| <command id='end'> |
| <params> |
| <param name='end' doc='End current mode and change to enable mode.' /> |
| </params> |
| </command> |
| </node> |
| <node id='view'> |
| <name>view</name> |
| <command id='show version'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='version' doc='Displays program version' /> |
| </params> |
| </command> |
| <command id='show online-help'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='online-help' doc='Online help' /> |
| </params> |
| </command> |
| <command id='enable'> |
| <params> |
| <param name='enable' doc='Turn on privileged mode command' /> |
| </params> |
| </command> |
| <command id='terminal length <0-512>'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='length' doc='Set number of lines on a screen' /> |
| <param name='<0-512>' doc='Number of lines on screen (0 for no pausing)' /> |
| </params> |
| </command> |
| <command id='terminal no length'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='length' doc='Set number of lines on a screen' /> |
| </params> |
| </command> |
| <command id='who'> |
| <params> |
| <param name='who' doc='Display who is on vty' /> |
| </params> |
| </command> |
| <command id='show history'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='history' doc='Display the session command history' /> |
| </params> |
| </command> |
| <command id='logging enable'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='enable' doc='Enables logging to this vty' /> |
| </params> |
| </command> |
| <command id='logging disable'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='disable' doc='Disables logging to this vty' /> |
| </params> |
| </command> |
| <command id='logging filter all (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='filter' doc='Filter log messages' /> |
| <param name='all' doc='Do you want to log all messages?' /> |
| <param name='0' doc='Only print messages matched by other filters' /> |
| <param name='1' doc='Bypass filter and print all messages' /> |
| </params> |
| </command> |
| <command id='logging color (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='color' doc='Configure color-printing for log messages' /> |
| <param name='0' doc='Don't use color for printing messages' /> |
| <param name='1' doc='Use color for printing messages' /> |
| </params> |
| </command> |
| <command id='logging timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp' /> |
| </params> |
| </command> |
| <command id='logging print extended-timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='extended-timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' /> |
| </params> |
| </command> |
| <command id='logging print category (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem name' /> |
| </params> |
| </command> |
| <command id='logging print category-hex (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category-hex' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem nr in hex ('<000b>')' /> |
| </params> |
| </command> |
| <command id='logging print level (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='level' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the log level name' /> |
| </params> |
| </command> |
| <command id='logging print file (0|1|basename) [last]'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='file' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the source file and line' /> |
| <param name='basename' doc='Prefix each log message with the source file's basename (strip leading paths) and line' /> |
| <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' /> |
| </params> |
| </command> |
| <command id='logging set-log-mask MASK'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='set-log-mask' doc='Set the logmask of this logging target' /> |
| <param name='MASK' doc='List of logging categories to log, e.g. 'abc:mno:xyz'. Available log categories depend on the specific application, refer to the 'logging level' command. Optionally add individual log levels like 'abc,1:mno,3:xyz,5', where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' /> |
| </params> |
| </command> |
| <command id='logging level (main|db|auc|ss|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='main' doc='Main Program' /> |
| <param name='db' doc='Database Layer' /> |
| <param name='auc' doc='Authentication Center' /> |
| <param name='ss' doc='Supplementary Services' /> |
| <param name='lglobal' doc='Library-internal global log family' /> |
| <param name='llapd' doc='LAPD in libosmogsm' /> |
| <param name='linp' doc='A-bis Intput Subsystem' /> |
| <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' /> |
| <param name='lmi' doc='A-bis Input Driver for Signalling' /> |
| <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' /> |
| <param name='lsms' doc='Layer3 Short Message Service (SMS)' /> |
| <param name='lctrl' doc='Control Interface' /> |
| <param name='lgtp' doc='GPRS GTP library' /> |
| <param name='lstats' doc='Statistics messages and logging' /> |
| <param name='lgsup' doc='Generic Subscriber Update Protocol' /> |
| <param name='loap' doc='Osmocom Authentication Protocol' /> |
| <param name='lss7' doc='libosmo-sigtran Signalling System 7' /> |
| <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' /> |
| <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' /> |
| <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' /> |
| <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' /> |
| <param name='ljibuf' doc='libosmo-netif Jitter Buffer' /> |
| <param name='lrspro' doc='Remote SIM protocol' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level set-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level force-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the 'no logging level force-all' command. Note: any 'logging level <category> <level>' commands will have no visible effect after this, until the forced level is released.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='no logging level force-all'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Release any globally forced log level set with 'logging level force-all <level>'' /> |
| </params> |
| </command> |
| <command id='show logging vty'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='logging' doc='Show current logging configuration' /> |
| <param name='vty' doc='Show current logging configuration for this vty' /> |
| </params> |
| </command> |
| <command id='show alarms'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='alarms' doc='Show current logging configuration' /> |
| </params> |
| </command> |
| <command id='show talloc-context (application|all) (full|brief|DEPTH)'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='talloc-context' doc='Show talloc memory hierarchy' /> |
| <param name='application' doc='Application's context' /> |
| <param name='all' doc='All contexts, if NULL-context tracking is enabled' /> |
| <param name='full' doc='Display a full talloc memory hierarchy' /> |
| <param name='brief' doc='Display a brief talloc memory hierarchy' /> |
| <param name='DEPTH' doc='Specify required maximal depth value' /> |
| </params> |
| </command> |
| <command id='show talloc-context (application|all) (full|brief|DEPTH) tree ADDRESS'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='talloc-context' doc='Show talloc memory hierarchy' /> |
| <param name='application' doc='Application's context' /> |
| <param name='all' doc='All contexts, if NULL-context tracking is enabled' /> |
| <param name='full' doc='Display a full talloc memory hierarchy' /> |
| <param name='brief' doc='Display a brief talloc memory hierarchy' /> |
| <param name='DEPTH' doc='Specify required maximal depth value' /> |
| <param name='tree' doc='Display only a specific memory chunk' /> |
| <param name='ADDRESS' doc='Chunk address (e.g. 0xdeadbeef)' /> |
| </params> |
| </command> |
| <command id='show talloc-context (application|all) (full|brief|DEPTH) filter REGEXP'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='talloc-context' doc='Show talloc memory hierarchy' /> |
| <param name='application' doc='Application's context' /> |
| <param name='all' doc='All contexts, if NULL-context tracking is enabled' /> |
| <param name='full' doc='Display a full talloc memory hierarchy' /> |
| <param name='brief' doc='Display a brief talloc memory hierarchy' /> |
| <param name='DEPTH' doc='Specify required maximal depth value' /> |
| <param name='filter' doc='Filter chunks using regular expression' /> |
| <param name='REGEXP' doc='Regular expression' /> |
| </params> |
| </command> |
| <command id='show stats'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='stats' doc='Show statistical values' /> |
| </params> |
| </command> |
| <command id='show stats level (global|peer|subscriber)'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='stats' doc='Show statistical values' /> |
| <param name='level' doc='Set the maximum group level' /> |
| <param name='global' doc='Show global groups only' /> |
| <param name='peer' doc='Show global and network peer related groups' /> |
| <param name='subscriber' doc='Show global, peer, and subscriber groups' /> |
| </params> |
| </command> |
| <command id='show asciidoc counters'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='asciidoc' doc='Asciidoc generation' /> |
| <param name='counters' doc='Generate table of all registered counters' /> |
| </params> |
| </command> |
| <command id='show rate-counters'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='rate-counters' doc='Show all rate counters' /> |
| </params> |
| </command> |
| <command id='show gsup-connections'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='gsup-connections' doc='GSUP Connections from VLRs, SGSNs, EUSEs' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT show'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='show' doc='Show subscriber information' /> |
| </params> |
| </command> |
| <command id='show subscriber (imsi|msisdn|id|imei) IDENT'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| </params> |
| </command> |
| </node> |
| <node id='enable'> |
| <name>enable</name> |
| <command id='disable'> |
| <params> |
| <param name='disable' doc='Turn off privileged mode command' /> |
| </params> |
| </command> |
| <command id='configure terminal'> |
| <params> |
| <param name='configure' doc='Configuration from vty interface' /> |
| <param name='terminal' doc='Configuration terminal' /> |
| </params> |
| </command> |
| <command id='copy running-config startup-config'> |
| <params> |
| <param name='copy' doc='Copy configuration' /> |
| <param name='running-config' doc='Copy running config to... ' /> |
| <param name='startup-config' doc='Copy running config to startup config (same as write file)' /> |
| </params> |
| </command> |
| <command id='show startup-config'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='startup-config' doc='Contentes of startup configuration' /> |
| </params> |
| </command> |
| <command id='show version'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='version' doc='Displays program version' /> |
| </params> |
| </command> |
| <command id='show online-help'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='online-help' doc='Online help' /> |
| </params> |
| </command> |
| <command id='terminal length <0-512>'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='length' doc='Set number of lines on a screen' /> |
| <param name='<0-512>' doc='Number of lines on screen (0 for no pausing)' /> |
| </params> |
| </command> |
| <command id='terminal no length'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='length' doc='Set number of lines on a screen' /> |
| </params> |
| </command> |
| <command id='who'> |
| <params> |
| <param name='who' doc='Display who is on vty' /> |
| </params> |
| </command> |
| <command id='show history'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='history' doc='Display the session command history' /> |
| </params> |
| </command> |
| <command id='terminal monitor'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='monitor' doc='Copy debug output to the current terminal line' /> |
| </params> |
| </command> |
| <command id='terminal no monitor'> |
| <params> |
| <param name='terminal' doc='Set terminal line parameters' /> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='monitor' doc='Copy debug output to the current terminal line' /> |
| </params> |
| </command> |
| <command id='logging enable'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='enable' doc='Enables logging to this vty' /> |
| </params> |
| </command> |
| <command id='logging disable'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='disable' doc='Disables logging to this vty' /> |
| </params> |
| </command> |
| <command id='logging filter all (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='filter' doc='Filter log messages' /> |
| <param name='all' doc='Do you want to log all messages?' /> |
| <param name='0' doc='Only print messages matched by other filters' /> |
| <param name='1' doc='Bypass filter and print all messages' /> |
| </params> |
| </command> |
| <command id='logging color (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='color' doc='Configure color-printing for log messages' /> |
| <param name='0' doc='Don't use color for printing messages' /> |
| <param name='1' doc='Use color for printing messages' /> |
| </params> |
| </command> |
| <command id='logging timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp' /> |
| </params> |
| </command> |
| <command id='logging print extended-timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='extended-timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' /> |
| </params> |
| </command> |
| <command id='logging print category (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem name' /> |
| </params> |
| </command> |
| <command id='logging print category-hex (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category-hex' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem nr in hex ('<000b>')' /> |
| </params> |
| </command> |
| <command id='logging print level (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='level' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the log level name' /> |
| </params> |
| </command> |
| <command id='logging print file (0|1|basename) [last]'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='file' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the source file and line' /> |
| <param name='basename' doc='Prefix each log message with the source file's basename (strip leading paths) and line' /> |
| <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' /> |
| </params> |
| </command> |
| <command id='logging set-log-mask MASK'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='set-log-mask' doc='Set the logmask of this logging target' /> |
| <param name='MASK' doc='List of logging categories to log, e.g. 'abc:mno:xyz'. Available log categories depend on the specific application, refer to the 'logging level' command. Optionally add individual log levels like 'abc,1:mno,3:xyz,5', where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' /> |
| </params> |
| </command> |
| <command id='logging level (main|db|auc|ss|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='main' doc='Main Program' /> |
| <param name='db' doc='Database Layer' /> |
| <param name='auc' doc='Authentication Center' /> |
| <param name='ss' doc='Supplementary Services' /> |
| <param name='lglobal' doc='Library-internal global log family' /> |
| <param name='llapd' doc='LAPD in libosmogsm' /> |
| <param name='linp' doc='A-bis Intput Subsystem' /> |
| <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' /> |
| <param name='lmi' doc='A-bis Input Driver for Signalling' /> |
| <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' /> |
| <param name='lsms' doc='Layer3 Short Message Service (SMS)' /> |
| <param name='lctrl' doc='Control Interface' /> |
| <param name='lgtp' doc='GPRS GTP library' /> |
| <param name='lstats' doc='Statistics messages and logging' /> |
| <param name='lgsup' doc='Generic Subscriber Update Protocol' /> |
| <param name='loap' doc='Osmocom Authentication Protocol' /> |
| <param name='lss7' doc='libosmo-sigtran Signalling System 7' /> |
| <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' /> |
| <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' /> |
| <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' /> |
| <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' /> |
| <param name='ljibuf' doc='libosmo-netif Jitter Buffer' /> |
| <param name='lrspro' doc='Remote SIM protocol' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level set-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> <param name='level' doc='Set the log level for a specified category' /> |
| <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level force-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the 'no logging level force-all' command. Note: any 'logging level <category> <level>' commands will have no visible effect after this, until the forced level is released.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='no logging level force-all'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Release any globally forced log level set with 'logging level force-all <level>'' /> |
| </params> |
| </command> |
| <command id='show logging vty'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='logging' doc='Show current logging configuration' /> |
| <param name='vty' doc='Show current logging configuration for this vty' /> |
| </params> |
| </command> |
| <command id='show alarms'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='alarms' doc='Show current logging configuration' /> |
| </params> |
| </command> |
| <command id='show talloc-context (application|all) (full|brief|DEPTH)'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='talloc-context' doc='Show talloc memory hierarchy' /> |
| <param name='application' doc='Application's context' /> |
| <param name='all' doc='All contexts, if NULL-context tracking is enabled' /> |
| <param name='full' doc='Display a full talloc memory hierarchy' /> |
| <param name='brief' doc='Display a brief talloc memory hierarchy' /> |
| <param name='DEPTH' doc='Specify required maximal depth value' /> |
| </params> |
| </command> |
| <command id='show talloc-context (application|all) (full|brief|DEPTH) tree ADDRESS'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='talloc-context' doc='Show talloc memory hierarchy' /> |
| <param name='application' doc='Application's context' /> |
| <param name='all' doc='All contexts, if NULL-context tracking is enabled' /> |
| <param name='full' doc='Display a full talloc memory hierarchy' /> |
| <param name='brief' doc='Display a brief talloc memory hierarchy' /> |
| <param name='DEPTH' doc='Specify required maximal depth value' /> |
| <param name='tree' doc='Display only a specific memory chunk' /> |
| <param name='ADDRESS' doc='Chunk address (e.g. 0xdeadbeef)' /> |
| </params> |
| </command> |
| <command id='show talloc-context (application|all) (full|brief|DEPTH) filter REGEXP'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='talloc-context' doc='Show talloc memory hierarchy' /> |
| <param name='application' doc='Application's context' /> |
| <param name='all' doc='All contexts, if NULL-context tracking is enabled' /> |
| <param name='full' doc='Display a full talloc memory hierarchy' /> |
| <param name='brief' doc='Display a brief talloc memory hierarchy' /> |
| <param name='DEPTH' doc='Specify required maximal depth value' /> |
| <param name='filter' doc='Filter chunks using regular expression' /> |
| <param name='REGEXP' doc='Regular expression' /> |
| </params> |
| </command> |
| <command id='show stats'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='stats' doc='Show statistical values' /> |
| </params> |
| </command> |
| <command id='show stats level (global|peer|subscriber)'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='stats' doc='Show statistical values' /> |
| <param name='level' doc='Set the maximum group level' /> |
| <param name='global' doc='Show global groups only' /> |
| <param name='peer' doc='Show global and network peer related groups' /> |
| <param name='subscriber' doc='Show global, peer, and subscriber groups' /> |
| </params> |
| </command> |
| <command id='show asciidoc counters'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='asciidoc' doc='Asciidoc generation' /> |
| <param name='counters' doc='Generate table of all registered counters' /> |
| </params> |
| </command> |
| <command id='show rate-counters'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='rate-counters' doc='Show all rate counters' /> |
| </params> |
| </command> |
| <command id='show gsup-connections'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='gsup-connections' doc='GSUP Connections from VLRs, SGSNs, EUSEs' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT show'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='show' doc='Show subscriber information' /> |
| </params> |
| </command> |
| <command id='show subscriber (imsi|msisdn|id|imei) IDENT'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| </params> |
| </command> |
| <command id='subscriber imsi IDENT create'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID of the subscriber' /> |
| <param name='create' doc='Create subscriber by IMSI' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT delete'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='delete' doc='Delete subscriber from database' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT update msisdn (none|MSISDN)'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='update' doc='Set or update subscriber data' /> |
| <param name='msisdn' doc='Set MSISDN (phone number) of the subscriber' /> |
| <param name='none' doc='Remove MSISDN (phone number)' /> |
| <param name='MSISDN' doc='New MSISDN (phone number)' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT update aud2g none'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='update' doc='Set or update subscriber data' /> |
| <param name='aud2g' doc='Set 2G authentication data' /> |
| <param name='none' doc='Delete 2G authentication data' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT update aud2g (comp128v1|comp128v2|comp128v3|xor) ki KI'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='update' doc='Set or update subscriber data' /> |
| <param name='aud2g' doc='Set 2G authentication data' /> |
| <param name='comp128v1' doc='Use COMP128v1 algorithm' /> |
| <param name='comp128v2' doc='Use COMP128v2 algorithm' /> |
| <param name='comp128v3' doc='Use COMP128v3 algorithm' /> |
| <param name='xor' doc='Use XOR algorithm' /> |
| <param name='ki' doc='Set Ki Encryption Key' /> |
| <param name='KI' doc='Ki as 32 hexadecimal characters' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT update aud3g none'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='update' doc='Set or update subscriber data' /> |
| <param name='aud3g' doc='Set UMTS authentication data (3G, and 2G with UMTS AKA)' /> |
| <param name='none' doc='Delete 3G authentication data' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT update aud3g milenage k K (op|opc) OP_C [ind-bitlen] [<0-28>]'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='update' doc='Set or update subscriber data' /> |
| <param name='aud3g' doc='Set UMTS authentication data (3G, and 2G with UMTS AKA)' /> |
| <param name='milenage' doc='Use Milenage algorithm' /> |
| <param name='k' doc='Set Encryption Key K' /> |
| <param name='K' doc='K as 32 hexadecimal characters' /> |
| <param name='op' doc='Set OP key' /> |
| <param name='opc' doc='Set OPC key' /> |
| <param name='OP_C' doc='OP or OPC as 32 hexadecimal characters' /> |
| <param name='[ind-bitlen]' doc='Set IND bit length' /> |
| <param name='[<0-28>]' doc='IND bit length value (default: 5)' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT update imei (none|IMEI)'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='update' doc='Set or update subscriber data' /> |
| <param name='imei' doc='Set IMEI of the subscriber (normally populated from MSC, no need to set this manually)' /> |
| <param name='none' doc='Forget IMEI' /> |
| <param name='IMEI' doc='Set IMEI (use for debug only!)' /> |
| </params> |
| </command> |
| <command id='subscriber (imsi|msisdn|id|imei) IDENT update network-access-mode (none|cs|ps|cs+ps)'> |
| <params> |
| <param name='subscriber' doc='Subscriber management commands' /> |
| <param name='imsi' doc='Identify subscriber by IMSI' /> |
| <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' /> |
| <param name='id' doc='Identify subscriber by database ID' /> |
| <param name='imei' doc='Identify subscriber by IMEI' /> |
| <param name='IDENT' doc='IMSI/MSISDN/ID/IMEI of the subscriber' /> |
| <param name='update' doc='Set or update subscriber data' /> |
| <param name='network-access-mode' doc='Set Network Access Mode (NAM) of the subscriber' /> |
| <param name='none' doc='Do not allow access to circuit switched or packet switched services' /> |
| <param name='cs' doc='Allow access to circuit switched services only' /> |
| <param name='ps' doc='Allow access to packet switched services only' /> |
| <param name='cs+ps' doc='Allow access to both circuit and packet switched services' /> |
| </params> |
| </command> |
| </node> |
| <node id='config'> |
| <name>config</name> |
| <command id='hostname WORD'> |
| <params> |
| <param name='hostname' doc='Set system's network name' /> |
| <param name='WORD' doc='This system's network name' /> |
| </params> |
| </command> |
| <command id='no hostname [HOSTNAME]'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='hostname' doc='Reset system's network name' /> |
| <param name='[HOSTNAME]' doc='Host name of this router' /> |
| </params> |
| </command> |
| <command id='password (8|) WORD'> |
| <params> |
| <param name='password' doc='Assign the terminal connection password' /> |
| <param name='8' doc='Specifies a HIDDEN password will follow' /> |
| <param name='' doc='dummy string ' /> |
| <param name='WORD' doc='The HIDDEN line password string' /> |
| </params> |
| </command> |
| <command id='password LINE'> |
| <params> |
| <param name='password' doc='Assign the terminal connection password' /> |
| <param name='LINE' doc='The UNENCRYPTED (cleartext) line password' /> |
| </params> |
| </command> |
| <command id='enable password (8|) WORD'> |
| <params> |
| <param name='enable' doc='Modify enable password parameters' /> |
| <param name='password' doc='Assign the privileged level password' /> |
| <param name='8' doc='Specifies a HIDDEN password will follow' /> |
| <param name='' doc='dummy string ' /> |
| <param name='WORD' doc='The HIDDEN 'enable' password string' /> |
| </params> |
| </command> |
| <command id='enable password LINE'> |
| <params> |
| <param name='enable' doc='Modify enable password parameters' /> |
| <param name='password' doc='Assign the privileged level password' /> |
| <param name='LINE' doc='The UNENCRYPTED (cleartext) 'enable' password' /> |
| </params> |
| </command> |
| <command id='no enable password'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='enable' doc='Modify enable password parameters' /> |
| <param name='password' doc='Assign the privileged level password' /> |
| </params> |
| </command> |
| <command id='banner motd default'> |
| <params> |
| <param name='banner' doc='Set banner string' /> |
| <param name='motd' doc='Strings for motd' /> |
| <param name='default' doc='Default string' /> |
| </params> |
| </command> |
| <command id='banner motd file [FILE]'> |
| <params> |
| <param name='banner' doc='Set banner' /> |
| <param name='motd' doc='Banner for motd' /> |
| <param name='file' doc='Banner from a file' /> |
| <param name='[FILE]' doc='Filename' /> |
| </params> |
| </command> |
| <command id='no banner motd'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='banner' doc='Set banner string' /> |
| <param name='motd' doc='Strings for motd' /> |
| </params> |
| </command> |
| <command id='service terminal-length <0-512>'> |
| <params> |
| <param name='service' doc='Set up miscellaneous service' /> |
| <param name='terminal-length' doc='System wide terminal length configuration' /> |
| <param name='<0-512>' doc='Number of lines of VTY (0 means no line control)' /> |
| </params> |
| </command> |
| <command id='no service terminal-length [<0-512>]'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='service' doc='Set up miscellaneous service' /> |
| <param name='terminal-length' doc='System wide terminal length configuration' /> |
| <param name='[<0-512>]' doc='Number of lines of VTY (0 means no line control)' /> |
| </params> |
| </command> |
| <command id='line vty'> |
| <params> |
| <param name='line' doc='Configure a terminal line' /> |
| <param name='vty' doc='Virtual terminal' /> |
| </params> |
| </command> |
| <command id='service advanced-vty'> |
| <params> |
| <param name='service' doc='Set up miscellaneous service' /> |
| <param name='advanced-vty' doc='Enable advanced mode vty interface' /> |
| </params> |
| </command> |
| <command id='no service advanced-vty'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='service' doc='Set up miscellaneous service' /> |
| <param name='advanced-vty' doc='Enable advanced mode vty interface' /> |
| </params> |
| </command> |
| <command id='show history'> |
| <params> |
| <param name='show' doc='Show running system information' /> |
| <param name='history' doc='Display the session command history' /> |
| </params> |
| </command> |
| <command id='ctrl'> |
| <params> |
| <param name='ctrl' doc='Configure the Control Interface' /> |
| </params> |
| </command> |
| <command id='log stderr'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='stderr' doc='Logging via STDERR of the process' /> |
| </params> |
| </command> |
| <command id='no log stderr'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='stderr' doc='Logging via STDERR of the process' /> |
| </params> |
| </command> |
| <command id='log file .FILENAME'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='file' doc='Logging to text file' /> |
| <param name='.FILENAME' doc='Filename' /> |
| </params> |
| </command> |
| <command id='no log file .FILENAME'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='file' doc='Logging to text file' /> |
| <param name='.FILENAME' doc='Filename' /> |
| </params> |
| </command> |
| <command id='log alarms <2-32700>'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='alarms' doc='Logging alarms to osmo_strrb' /> |
| <param name='<2-32700>' doc='Maximum number of messages to log' /> |
| </params> |
| </command> |
| <command id='no log alarms'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='alarms' doc='Logging alarms to osmo_strrb' /> |
| </params> |
| </command> |
| <command id='log syslog (authpriv|cron|daemon|ftp|lpr|mail|news|user|uucp)'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='syslog' doc='Logging via syslog' /> |
| <param name='authpriv' doc='Security/authorization messages facility' /> |
| <param name='cron' doc='Clock daemon (cron/at) facility' /> |
| <param name='daemon' doc='General system daemon facility' /> |
| <param name='ftp' doc='Ftp daemon facility' /> |
| <param name='lpr' doc='Line printer facility' /> |
| <param name='mail' doc='Mail facility' /> |
| <param name='news' doc='News facility' /> |
| <param name='user' doc='Generic facility' /> |
| <param name='uucp' doc='UUCP facility' /> |
| </params> |
| </command> |
| <command id='log syslog local <0-7>'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='syslog' doc='Logging via syslog' /> |
| <param name='local' doc='Syslog LOCAL facility' /> |
| <param name='<0-7>' doc='Local facility number' /> |
| </params> |
| </command> |
| <command id='no log syslog'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='syslog' doc='Logging via syslog' /> |
| </params> |
| </command> |
| <command id='log gsmtap [HOSTNAME]'> |
| <params> |
| <param name='log' doc='Configure logging sub-system' /> |
| <param name='gsmtap' doc='Logging via GSMTAP' /> |
| <param name='[HOSTNAME]' doc='Host name to send the GSMTAP logging to (UDP port 4729)' /> |
| </params> |
| </command> |
| <command id='stats reporter statsd'> |
| <params> |
| <param name='stats' doc='Configure stats sub-system' /> |
| <param name='reporter' doc='Configure a stats reporter' /> |
| <param name='statsd' doc='Report to a STATSD server' /> |
| </params> |
| </command> |
| <command id='no stats reporter statsd'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='stats' doc='Configure stats sub-system' /> |
| <param name='reporter' doc='Configure a stats reporter' /> |
| <param name='statsd' doc='Report to a STATSD server' /> |
| </params> |
| </command> |
| <command id='stats reporter log'> |
| <params> |
| <param name='stats' doc='Configure stats sub-system' /> |
| <param name='reporter' doc='Configure a stats reporter' /> |
| <param name='log' doc='Report to the logger' /> |
| </params> |
| </command> |
| <command id='no stats reporter log'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='stats' doc='Configure stats sub-system' /> |
| <param name='reporter' doc='Configure a stats reporter' /> |
| <param name='log' doc='Report to the logger' /> |
| </params> |
| </command> |
| <command id='stats interval <1-65535>'> |
| <params> |
| <param name='stats' doc='Configure stats sub-system' /> |
| <param name='interval' doc='Set the reporting interval' /> |
| <param name='<1-65535>' doc='Interval in seconds' /> |
| </params> |
| </command> |
| <command id='hlr'> |
| <params> |
| <param name='hlr' doc='Configure the HLR' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-log'> |
| <name>config-log</name> |
| <command id='logging filter all (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='filter' doc='Filter log messages' /> |
| <param name='all' doc='Do you want to log all messages?' /> |
| <param name='0' doc='Only print messages matched by other filters' /> |
| <param name='1' doc='Bypass filter and print all messages' /> |
| </params> |
| </command> |
| <command id='logging color (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='color' doc='Configure color-printing for log messages' /> |
| <param name='0' doc='Don't use color for printing messages' /> |
| <param name='1' doc='Use color for printing messages' /> |
| </params> |
| </command> |
| <command id='logging timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp' /> |
| </params> |
| </command> |
| <command id='logging print extended-timestamp (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='extended-timestamp' doc='Configure log message timestamping' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' /> |
| </params> |
| </command> |
| <command id='logging print category (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem name' /> |
| </params> |
| </command> |
| <command id='logging print category-hex (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='category-hex' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with category/subsystem nr in hex ('<000b>')' /> |
| </params> |
| </command> |
| <command id='logging print level (0|1)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='level' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the log level name' /> |
| </params> |
| </command> |
| <command id='logging print file (0|1|basename) [last]'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='print' doc='Log output settings' /> |
| <param name='file' doc='Configure log message' /> |
| <param name='0' doc='Don't prefix each log message' /> |
| <param name='1' doc='Prefix each log message with the source file and line' /> |
| <param name='basename' doc='Prefix each log message with the source file's basename (strip leading paths) and line' /> |
| <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' /> |
| </params> |
| </command> |
| <command id='logging level (main|db|auc|ss|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='main' doc='Main Program' /> |
| <param name='db' doc='Database Layer' /> |
| <param name='auc' doc='Authentication Center' /> |
| <param name='ss' doc='Supplementary Services' /> |
| <param name='lglobal' doc='Library-internal global log family' /> |
| <param name='llapd' doc='LAPD in libosmogsm' /> |
| <param name='linp' doc='A-bis Intput Subsystem' /> |
| <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' /> |
| <param name='lmi' doc='A-bis Input Driver for Signalling' /> |
| <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' /> |
| <param name='lsms' doc='Layer3 Short Message Service (SMS)' /> |
| <param name='lctrl' doc='Control Interface' /> |
| <param name='lgtp' doc='GPRS GTP library' /> |
| <param name='lstats' doc='Statistics messages and logging' /> |
| <param name='lgsup' doc='Generic Subscriber Update Protocol' /> |
| <param name='loap' doc='Osmocom Authentication Protocol' /> |
| <param name='lss7' doc='libosmo-sigtran Signalling System 7' /> |
| <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' /> |
| <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' /> |
| <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' /> |
| <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' /> |
| <param name='ljibuf' doc='libosmo-netif Jitter Buffer' /> |
| <param name='lrspro' doc='Remote SIM protocol' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level set-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='logging level force-all (debug|info|notice|error|fatal)'> |
| <params> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the 'no logging level force-all' command. Note: any 'logging level <category> <level>' commands will have no visible effect after this, until the forced level is released.' /> |
| <param name='debug' doc='Log debug messages and higher levels' /> |
| <param name='info' doc='Log informational messages and higher levels' /> |
| <param name='notice' doc='Log noticeable messages and higher levels' /> |
| <param name='error' doc='Log error messages and higher levels' /> |
| <param name='fatal' doc='Log only fatal messages' /> |
| </params> |
| </command> |
| <command id='no logging level force-all'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='logging' doc='Configure logging' /> |
| <param name='level' doc='Set the log level for a specified category' /> |
| <param name='force-all' doc='Release any globally forced log level set with 'logging level force-all <level>'' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-stats'> |
| <name>config-stats</name> |
| <command id='local-ip ADDR'> |
| <params> |
| <param name='local-ip' doc='Set the IP address to which we bind locally' /> |
| <param name='ADDR' doc='IP Address' /> |
| </params> |
| </command> |
| <command id='no local-ip'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='local-ip' doc='Set the IP address to which we bind locally' /> |
| </params> |
| </command> |
| <command id='remote-ip ADDR'> |
| <params> |
| <param name='remote-ip' doc='Set the remote IP address to which we connect' /> |
| <param name='ADDR' doc='IP Address' /> |
| </params> |
| </command> |
| <command id='remote-port <1-65535>'> |
| <params> |
| <param name='remote-port' doc='Set the remote port to which we connect' /> |
| <param name='<1-65535>' doc='Remote port number' /> |
| </params> |
| </command> |
| <command id='mtu <100-65535>'> |
| <params> |
| <param name='mtu' doc='Set the maximum packet size' /> |
| <param name='<100-65535>' doc='Size in byte' /> |
| </params> |
| </command> |
| <command id='no mtu'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='mtu' doc='Set the maximum packet size' /> |
| </params> |
| </command> |
| <command id='prefix PREFIX'> |
| <params> |
| <param name='prefix' doc='Set the item name prefix' /> |
| <param name='PREFIX' doc='The prefix string' /> |
| </params> |
| </command> |
| <command id='no prefix'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='prefix' doc='Set the item name prefix' /> |
| </params> |
| </command> |
| <command id='level (global|peer|subscriber)'> |
| <params> |
| <param name='level' doc='Set the maximum group level' /> |
| <param name='global' doc='Report global groups only' /> |
| <param name='peer' doc='Report global and network peer related groups' /> |
| <param name='subscriber' doc='Report global, peer, and subscriber groups' /> |
| </params> |
| </command> |
| <command id='enable'> |
| <params> |
| <param name='enable' doc='Enable the reporter' /> |
| </params> |
| </command> |
| <command id='disable'> |
| <params> |
| <param name='disable' doc='Disable the reporter' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-line'> |
| <name>config-line</name> |
| <command id='login'> |
| <params> |
| <param name='login' doc='Enable password checking' /> |
| </params> |
| </command> |
| <command id='no login'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='login' doc='Enable password checking' /> |
| </params> |
| </command> |
| <command id='bind A.B.C.D [<0-65535>]'> |
| <params> |
| <param name='bind' doc='Accept VTY telnet connections on local interface' /> |
| <param name='A.B.C.D' doc='Local interface IP address (default: 127.0.0.1)' /> |
| <param name='[<0-65535>]' doc='Local TCP port number' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-ctrl'> |
| <name>config-ctrl</name> |
| <command id='bind A.B.C.D'> |
| <params> |
| <param name='bind' doc='Set bind address to listen for Control connections' /> |
| <param name='A.B.C.D' doc='Local IP address (default 127.0.0.1)' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-hlr'> |
| <name>config-hlr</name> |
| <command id='gsup'> |
| <params> |
| <param name='gsup' doc='Configure GSUP options' /> |
| </params> |
| </command> |
| <command id='database PATH'> |
| <params> |
| <param name='database' doc='Set the path to the HLR database file' /> |
| <param name='PATH' doc='Relative or absolute file system path to the database file (default is 'hlr.db')' /> |
| </params> |
| </command> |
| <command id='euse NAME'> |
| <params> |
| <param name='euse' doc='Configure a particular External USSD Entity' /> |
| <param name='NAME' doc='Alphanumeric name of the External USSD Entity' /> |
| </params> |
| </command> |
| <command id='no euse NAME'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='euse' doc='Remove a particular External USSD Entity' /> |
| <param name='NAME' doc='Alphanumeric name of the External USSD Entity' /> |
| </params> |
| </command> |
| <command id='ussd route prefix PREFIX internal (own-msisdn|own-imsi)'> |
| <params> |
| <param name='ussd' doc='USSD Configuration' /> |
| <param name='route' doc='Routing Configuration' /> |
| <param name='prefix' doc='Prefix-Matching Route' /> |
| <param name='PREFIX' doc='USSD Prefix' /> |
| <param name='internal' doc='Internal USSD Handler' /> |
| <param name='own-msisdn' doc='Respond with subscribers' own MSISDN' /> |
| <param name='own-imsi' doc='Respond with subscribers' own IMSI' /> |
| </params> |
| </command> |
| <command id='ussd route prefix PREFIX external EUSE'> |
| <params> |
| <param name='ussd' doc='USSD Configuration' /> |
| <param name='route' doc='Routing Configuration' /> |
| <param name='prefix' doc='Prefix-Matching Route' /> |
| <param name='PREFIX' doc='USSD Prefix' /> |
| <param name='external' doc='External USSD Handler' /> |
| <param name='EUSE' doc='Name of External USSD Handler (IPA CCM ID)' /> |
| </params> |
| </command> |
| <command id='no ussd route prefix PREFIX'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='ussd' doc='USSD Configuration' /> |
| <param name='route' doc='Routing Configuration' /> |
| <param name='prefix' doc='Prefix-Matching Route' /> |
| <param name='PREFIX' doc='USSD Prefix' /> |
| </params> |
| </command> |
| <command id='ussd default-route external EUSE'> |
| <params> |
| <param name='ussd' doc='USSD Configuration' /> |
| <param name='default-route' doc='Configure default-route for all USSD to unknown destinations' /> |
| <param name='external' doc='External USSD Handler' /> |
| <param name='EUSE' doc='Name of External USSD Handler (IPA CCM ID)' /> |
| </params> |
| </command> |
| <command id='no ussd default-route'> |
| <params> |
| <param name='no' doc='Negate a command or set its defaults' /> |
| <param name='ussd' doc='USSD Configuration' /> |
| <param name='default-route' doc='Remove the default-route for all USSD to unknown destinations' /> |
| </params> |
| </command> |
| <command id='ncss-guard-timeout <0-255>'> |
| <params> |
| <param name='ncss-guard-timeout' doc='Set guard timer for NCSS (call independent SS) session activity' /> |
| <param name='<0-255>' doc='Guard timer value (sec.), or 0 to disable' /> |
| </params> |
| </command> |
| <command id='store-imei'> |
| <params> |
| <param name='store-imei' doc='Save the IMEI in the database when receiving Check IMEI requests. Note that an MSC does not necessarily send Check IMEI requests (for OsmoMSC, you may want to set 'check-imei-rqd 1').' /> |
| </params> |
| </command> |
| <command id='no store-imei'> |
| <params> |
| <param name='no' doc='Do not save the IMEI in the database, when receiving Check IMEI requests.' /> |
| <param name='store-imei' doc='(null)' /> |
| </params> |
| </command> |
| <command id='subscriber-create-on-demand (no-msisdn|<3-15>) (none|cs|ps|cs+ps)'> |
| <params> |
| <param name='subscriber-create-on-demand' doc='Make a new record when a subscriber is first seen.' /> |
| <param name='no-msisdn' doc='Do not automatically assign MSISDN.' /> |
| <param name='<3-15>' doc='Length of an automatically assigned MSISDN.' /> |
| <param name='none' doc='Do not allow any NAM (Network Access Mode) by default.' /> |
| <param name='cs' doc='Allow access to circuit switched NAM by default.' /> |
| <param name='ps' doc='Allow access to packet switched NAM by default.' /> |
| <param name='cs+ps' doc='Allow access to circuit and packet switched NAM by default.' /> |
| </params> |
| </command> |
| <command id='no subscriber-create-on-demand'> |
| <params> |
| <param name='no' doc='Do not make a new record when a subscriber is first seen.' /> |
| <param name='subscriber-create-on-demand' doc='(null)' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-hlr-gsup'> |
| <name>config-hlr-gsup</name> |
| <command id='bind ip A.B.C.D'> |
| <params> |
| <param name='bind' doc='Listen/Bind related socket option' /> |
| <param name='ip' doc='IP information' /> |
| <param name='A.B.C.D' doc='IPv4 Address to bind the GSUP interface to' /> |
| </params> |
| </command> |
| </node> |
| <node id='config-hlr-euse'> |
| <name>config-hlr-euse</name> |
| </node> |
| </vtydoc> |