doc/manuals/vty/ggsn_vty_reference.xml

<vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'>
  <node id='_common_cmds_'>
    <name>Common Commands</name>
    <description>These commands are available on all VTY nodes. They are listed here only once, to unclutter the VTY reference.</description>
    <command id='help'>
      <params>
        <param name='help' doc='Description of the interactive help system' />
      </params>
    </command>
    <command id='list'>
      <params>
        <param name='list' doc='Print command list' />
      </params>
    </command>
    <command id='write terminal'>
      <params>
        <param name='write' doc='Write running configuration to memory, network, or terminal' />
        <param name='terminal' doc='Write to terminal' />
      </params>
    </command>
    <command id='write file'>
      <params>
        <param name='write' doc='Write running configuration to memory, network, or terminal' />
        <param name='file' doc='Write to configuration file' />
      </params>
    </command>
    <command id='write memory'>
      <params>
        <param name='write' doc='Write running configuration to memory, network, or terminal' />
        <param name='memory' doc='Write configuration to the file (same as write file)' />
      </params>
    </command>
    <command id='write'>
      <params>
        <param name='write' doc='Write running configuration to memory, network, or terminal' />
      </params>
    </command>
    <command id='show running-config'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='running-config' doc='running configuration' />
      </params>
    </command>
    <command id='exit'>
      <params>
        <param name='exit' doc='Exit current mode and down to previous mode' />
      </params>
    </command>
    <command id='end'>
      <params>
        <param name='end' doc='End current mode and change to enable mode.' />
      </params>
    </command>
  </node>
  <node id='view'>
    <name>view</name>
    <command id='show version'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='version' doc='Displays program version' />
      </params>
    </command>
    <command id='show online-help'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='online-help' doc='Online help' />
      </params>
    </command>
    <command id='enable'>
      <params>
        <param name='enable' doc='Turn on privileged mode command' />
      </params>
    </command>
    <command id='terminal length &lt;0-512&gt;'>
      <params>
        <param name='terminal' doc='Set terminal line parameters' />
        <param name='length' doc='Set number of lines on a screen' />
        <param name='&lt;0-512&gt;' doc='Number of lines on screen (0 for no pausing)' />
      </params>
    </command>
    <command id='terminal no length'>
      <params>
        <param name='terminal' doc='Set terminal line parameters' />
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='length' doc='Set number of lines on a screen' />
      </params>
    </command>
    <command id='echo .MESSAGE'>
      <params>
        <param name='echo' doc='Echo a message back to the vty' />
        <param name='.MESSAGE' doc='The message to echo' />
      </params>
    </command>
    <command id='who'>
      <params>
        <param name='who' doc='Display who is on vty' />
      </params>
    </command>
    <command id='show history'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='history' doc='Display the session command history' />
      </params>
    </command>
    <command id='logging enable'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='enable' doc='Enables logging to this vty' />
      </params>
    </command>
    <command id='logging disable'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='disable' doc='Disables logging to this vty' />
      </params>
    </command>
    <command id='logging filter all (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='filter' doc='Filter log messages' />
        <param name='all' doc='Do you want to log all messages?' />
        <param name='0' doc='Only print messages matched by other filters' />
        <param name='1' doc='Bypass filter and print all messages' />
      </params>
    </command>
    <command id='logging color (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='color' doc='Configure color-printing for log messages' />
        <param name='0' doc='Don&apos;t use color for printing messages' />
        <param name='1' doc='Use color for printing messages' />
      </params>
    </command>
    <command id='logging timestamp (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='timestamp' doc='Configure log message timestamping' />
        <param name='0' doc='Don&apos;t prefix each log message' />
        <param name='1' doc='Prefix each log message with current timestamp' />
      </params>
    </command>
    <command id='logging print extended-timestamp (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='print' doc='Log output settings' />
        <param name='extended-timestamp' doc='Configure log message timestamping' />
        <param name='0' doc='Don&apos;t prefix each log message' />
        <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
      </params>
    </command>
    <command id='logging print category (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='print' doc='Log output settings' />
        <param name='category' doc='Configure log message' />
        <param name='0' doc='Don&apos;t prefix each log message' />
        <param name='1' doc='Prefix each log message with category/subsystem name' />
      </params>
    </command>
    <command id='logging set-log-mask MASK'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='set-log-mask' doc='Set the logmask of this logging target' />
        <param name='MASK' doc='List of logging categories to log, e.g. &apos;abc:mno:xyz&apos;. Available log categories depend on the specific application, refer to the &apos;logging level&apos; command. Optionally add individual log levels like &apos;abc,1:mno,3:xyz,5&apos;, where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' />
      </params>
    </command>
    <command id='logging set log mask MASK'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='set' doc='Decide which categories to output.' />
        <param name='log' doc='Log commands' />
        <param name='mask' doc='Mask commands' />
        <param name='MASK' doc='&apos;set log mask&apos; is deprecated, please refer to the docs of &apos;set-log-mask&apos; instead' />
      </params>
    </command>
    <command id='logging level (all|ip|tun|ggsn|sgsn|icmp6|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp) (everything|debug|info|notice|error|fatal)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='level' doc='Set the log level for a specified category' />
        <param name='all' doc='Global setting for all subsystems' />
        <param name='ip' doc='IP Pool and other groups' />
        <param name='tun' doc='Tunnel interface' />
        <param name='ggsn' doc='GGSN' />
        <param name='sgsn' doc='SGSN Emulator' />
        <param name='icmp6' doc='ICMPv6' />
        <param name='lglobal' doc='Library-internal global log family' />
        <param name='llapd' doc='LAPD in libosmogsm' />
        <param name='linp' doc='A-bis Intput Subsystem' />
        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
        <param name='lmi' doc='A-bis Input Driver for Signalling' />
        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
        <param name='lctrl' doc='Control Interface' />
        <param name='lgtp' doc='GPRS GTP library' />
        <param name='lstats' doc='Statistics messages and logging' />
        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
        <param name='loap' doc='Osmocom Authentication Protocol' />
        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
        <param name='everything' doc='Don&apos;t use. It doesn&apos;t log anything' />
        <param name='debug' doc='Log debug messages and higher levels' />
        <param name='info' doc='Log informational messages and higher levels' />
        <param name='notice' doc='Log noticeable messages and higher levels' />
        <param name='error' doc='Log error messages and higher levels' />
        <param name='fatal' doc='Log only fatal messages' />
      </params>
    </command>
    <command id='show logging vty'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='logging' doc='Show current logging configuration' />
        <param name='vty' doc='Show current logging configuration for this vty' />
      </params>
    </command>
    <command id='show alarms'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='alarms' doc='Show current logging configuration' />
      </params>
    </command>
    <command id='show stats'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='stats' doc='Show statistical values' />
      </params>
    </command>
    <command id='show stats level (global|peer|subscriber)'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='stats' doc='Show statistical values' />
        <param name='level' doc='Set the maximum group level' />
        <param name='global' doc='Show global groups only' />
        <param name='peer' doc='Show global and network peer related groups' />
        <param name='subscriber' doc='Show global, peer, and subscriber groups' />
      </params>
    </command>
    <command id='show asciidoc counters'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='asciidoc' doc='Asciidoc generation' />
        <param name='counters' doc='Generate table of all registered counters' />
      </params>
    </command>
    <command id='show pdp-context ggsn NAME [apn APN]'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='pdp-context' doc='Show PDP Context Information' />
        <param name='ggsn' doc='Gateway GPRS Support NODE (GGSN)' />
        <param name='NAME' doc='GGSN Name' />
        <param name='[apn' doc='(null)' />
        <param name='APN]' doc='(null)' />
      </params>
    </command>
    <command id='show pdp-context imsi IMSI [&lt;0-15&gt;]'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='pdp-context' doc='Display information on PDP Context' />
        <param name='imsi' doc='PDP contexts for given IMSI' />
        <param name='IMSI' doc='PDP context for given NSAPI' />
        <param name='[&lt;0-15&gt;]' doc='(null)' />
      </params>
    </command>
    <command id='show ggsn [NAME]'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='ggsn' doc='Display information on the GGSN' />
        <param name='[NAME]' doc='(null)' />
      </params>
    </command>
  </node>
  <node id='enable'>
    <name>enable</name>
    <command id='disable'>
      <params>
        <param name='disable' doc='Turn off privileged mode command' />
      </params>
    </command>
    <command id='configure terminal'>
      <params>
        <param name='configure' doc='Configuration from vty interface' />
        <param name='terminal' doc='Configuration terminal' />
      </params>
    </command>
    <command id='copy running-config startup-config'>
      <params>
        <param name='copy' doc='Copy configuration' />
        <param name='running-config' doc='Copy running config to... ' />
        <param name='startup-config' doc='Copy running config to startup config (same as write file)' />
      </params>
    </command>
    <command id='show startup-config'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='startup-config' doc='Contentes of startup configuration' />
      </params>
    </command>
    <command id='show version'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='version' doc='Displays program version' />
      </params>
    </command>
    <command id='show online-help'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='online-help' doc='Online help' />
      </params>
    </command>
    <command id='terminal length &lt;0-512&gt;'>
      <params>
        <param name='terminal' doc='Set terminal line parameters' />
        <param name='length' doc='Set number of lines on a screen' />
        <param name='&lt;0-512&gt;' doc='Number of lines on screen (0 for no pausing)' />
      </params>
    </command>
    <command id='terminal no length'>
      <params>
        <param name='terminal' doc='Set terminal line parameters' />
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='length' doc='Set number of lines on a screen' />
      </params>
    </command>
    <command id='echo .MESSAGE'>
      <params>
        <param name='echo' doc='Echo a message back to the vty' />
        <param name='.MESSAGE' doc='The message to echo' />
      </params>
    </command>
    <command id='who'>
      <params>
        <param name='who' doc='Display who is on vty' />
      </params>
    </command>
    <command id='show history'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='history' doc='Display the session command history' />
      </params>
    </command>
    <command id='terminal monitor'>
      <params>
        <param name='terminal' doc='Set terminal line parameters' />
        <param name='monitor' doc='Copy debug output to the current terminal line' />
      </params>
    </command>
    <command id='terminal no monitor'>
      <params>
        <param name='terminal' doc='Set terminal line parameters' />
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='monitor' doc='Copy debug output to the current terminal line' />
      </params>
    </command>
    <command id='logging enable'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='enable' doc='Enables logging to this vty' />
      </params>
    </command>
    <command id='logging disable'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='disable' doc='Disables logging to this vty' />
      </params>
    </command>
    <command id='logging filter all (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='filter' doc='Filter log messages' />
        <param name='all' doc='Do you want to log all messages?' />
        <param name='0' doc='Only print messages matched by other filters' />
        <param name='1' doc='Bypass filter and print all messages' />
      </params>
    </command>
    <command id='logging color (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='color' doc='Configure color-printing for log messages' />
        <param name='0' doc='Don&apos;t use color for printing messages' />
        <param name='1' doc='Use color for printing messages' />
      </params>
    </command>
    <command id='logging timestamp (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='timestamp' doc='Configure log message timestamping' />
        <param name='0' doc='Don&apos;t prefix each log message' />
        <param name='1' doc='Prefix each log message with current timestamp' />
      </params>
    </command>
    <command id='logging print extended-timestamp (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='print' doc='Log output settings' />
        <param name='extended-timestamp' doc='Configure log message timestamping' />
        <param name='0' doc='Don&apos;t prefix each log message' />
        <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
      </params>
    </command>
    <command id='logging print category (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='print' doc='Log output settings' />
        <param name='category' doc='Configure log message' />
        <param name='0' doc='Don&apos;t prefix each log message' />
        <param name='1' doc='Prefix each log message with category/subsystem name' />
      </params>
    </command>
    <command id='logging set-log-mask MASK'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='set-log-mask' doc='Set the logmask of this logging target' />
        <param name='MASK' doc='List of logging categories to log, e.g. &apos;abc:mno:xyz&apos;. Available log categories depend on the specific application, refer to the &apos;logging level&apos; command. Optionally add individual log levels like &apos;abc,1:mno,3:xyz,5&apos;, where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' />
      </params>
    </command>
    <command id='logging set log mask MASK'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='set' doc='Decide which categories to output.' />
        <param name='log' doc='Log commands' />
        <param name='mask' doc='Mask commands' />
        <param name='MASK' doc='&apos;set log mask&apos; is deprecated, please refer to the docs of &apos;set-log-mask&apos; instead' />
      </params>
    </command>
    <command id='logging level (all|ip|tun|ggsn|sgsn|icmp6|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp) (everything|debug|info|notice|error|fatal)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='level' doc='Set the log level for a specified category' />
        <param name='all' doc='Global setting for all subsystems' />
        <param name='ip' doc='IP Pool and other groups' />
        <param name='tun' doc='Tunnel interface' />
        <param name='ggsn' doc='GGSN' />
        <param name='sgsn' doc='SGSN Emulator' />
        <param name='icmp6' doc='ICMPv6' />
        <param name='lglobal' doc='Library-internal global log family' />
        <param name='llapd' doc='LAPD in libosmogsm' />
        <param name='linp' doc='A-bis Intput Subsystem' />
        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
        <param name='lmi' doc='A-bis Input Driver for Signalling' />
        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
        <param name='lctrl' doc='Control Interface' />
        <param name='lgtp' doc='GPRS GTP library' />
        <param name='lstats' doc='Statistics messages and logging' />
        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
        <param name='loap' doc='Osmocom Authentication Protocol' />
        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
        <param name='everything' doc='Don&apos;t use. It doesn&apos;t log anything' />
        <param name='debug' doc='Log debug messages and higher levels' />
        <param name='info' doc='Log informational messages and higher levels' />
        <param name='notice' doc='Log noticeable messages and higher levels' />
        <param name='error' doc='Log error messages and higher levels' />
        <param name='fatal' doc='Log only fatal messages' />
      </params>
    </command>
    <command id='show logging vty'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='logging' doc='Show current logging configuration' />
        <param name='vty' doc='Show current logging configuration for this vty' />
      </params>
    </command>
    <command id='show alarms'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='alarms' doc='Show current logging configuration' />
      </params>
    </command>
    <command id='show stats'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='stats' doc='Show statistical values' />
      </params>
    </command>
    <command id='show stats level (global|peer|subscriber)'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='stats' doc='Show statistical values' />
        <param name='level' doc='Set the maximum group level' />
        <param name='global' doc='Show global groups only' />
        <param name='peer' doc='Show global and network peer related groups' />
        <param name='subscriber' doc='Show global, peer, and subscriber groups' />
      </params>
    </command>
    <command id='show asciidoc counters'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='asciidoc' doc='Asciidoc generation' />
        <param name='counters' doc='Generate table of all registered counters' />
      </params>
    </command>
    <command id='show pdp-context ggsn NAME [apn APN]'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='pdp-context' doc='Show PDP Context Information' />
        <param name='ggsn' doc='Gateway GPRS Support NODE (GGSN)' />
        <param name='NAME' doc='GGSN Name' />
        <param name='[apn' doc='(null)' />
        <param name='APN]' doc='(null)' />
      </params>
    </command>
    <command id='show pdp-context imsi IMSI [&lt;0-15&gt;]'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='pdp-context' doc='Display information on PDP Context' />
        <param name='imsi' doc='PDP contexts for given IMSI' />
        <param name='IMSI' doc='PDP context for given NSAPI' />
        <param name='[&lt;0-15&gt;]' doc='(null)' />
      </params>
    </command>
    <command id='show ggsn [NAME]'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='ggsn' doc='Display information on the GGSN' />
        <param name='[NAME]' doc='(null)' />
      </params>
    </command>
  </node>
  <node id='config'>
    <name>config</name>
    <command id='hostname WORD'>
      <params>
        <param name='hostname' doc='Set system&apos;s network name' />
        <param name='WORD' doc='This system&apos;s network name' />
      </params>
    </command>
    <command id='no hostname [HOSTNAME]'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='hostname' doc='Reset system&apos;s network name' />
        <param name='[HOSTNAME]' doc='Host name of this router' />
      </params>
    </command>
    <command id='password (8|) WORD'>
      <params>
        <param name='password' doc='Assign the terminal connection password' />
        <param name='8' doc='Specifies a HIDDEN password will follow' />
        <param name='' doc='dummy string ' />
        <param name='WORD' doc='The HIDDEN line password string' />
      </params>
    </command>
    <command id='password LINE'>
      <params>
        <param name='password' doc='Assign the terminal connection password' />
        <param name='LINE' doc='The UNENCRYPTED (cleartext) line password' />
      </params>
    </command>
    <command id='enable password (8|) WORD'>
      <params>
        <param name='enable' doc='Modify enable password parameters' />
        <param name='password' doc='Assign the privileged level password' />
        <param name='8' doc='Specifies a HIDDEN password will follow' />
        <param name='' doc='dummy string ' />
        <param name='WORD' doc='The HIDDEN &apos;enable&apos; password string' />
      </params>
    </command>
    <command id='enable password LINE'>
      <params>
        <param name='enable' doc='Modify enable password parameters' />
        <param name='password' doc='Assign the privileged level password' />
        <param name='LINE' doc='The UNENCRYPTED (cleartext) &apos;enable&apos; password' />
      </params>
    </command>
    <command id='no enable password'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='enable' doc='Modify enable password parameters' />
        <param name='password' doc='Assign the privileged level password' />
      </params>
    </command>
    <command id='banner motd default'>
      <params>
        <param name='banner' doc='Set banner string' />
        <param name='motd' doc='Strings for motd' />
        <param name='default' doc='Default string' />
      </params>
    </command>
    <command id='banner motd file [FILE]'>
      <params>
        <param name='banner' doc='Set banner' />
        <param name='motd' doc='Banner for motd' />
        <param name='file' doc='Banner from a file' />
        <param name='[FILE]' doc='Filename' />
      </params>
    </command>
    <command id='no banner motd'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='banner' doc='Set banner string' />
        <param name='motd' doc='Strings for motd' />
      </params>
    </command>
    <command id='service terminal-length &lt;0-512&gt;'>
      <params>
        <param name='service' doc='Set up miscellaneous service' />
        <param name='terminal-length' doc='System wide terminal length configuration' />
        <param name='&lt;0-512&gt;' doc='Number of lines of VTY (0 means no line control)' />
      </params>
    </command>
    <command id='no service terminal-length [&lt;0-512&gt;]'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='service' doc='Set up miscellaneous service' />
        <param name='terminal-length' doc='System wide terminal length configuration' />
        <param name='[&lt;0-512&gt;]' doc='Number of lines of VTY (0 means no line control)' />
      </params>
    </command>
    <command id='line vty'>
      <params>
        <param name='line' doc='Configure a terminal line' />
        <param name='vty' doc='Virtual terminal' />
      </params>
    </command>
    <command id='service advanced-vty'>
      <params>
        <param name='service' doc='Set up miscellaneous service' />
        <param name='advanced-vty' doc='Enable advanced mode vty interface' />
      </params>
    </command>
    <command id='no service advanced-vty'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='service' doc='Set up miscellaneous service' />
        <param name='advanced-vty' doc='Enable advanced mode vty interface' />
      </params>
    </command>
    <command id='show history'>
      <params>
        <param name='show' doc='Show running system information' />
        <param name='history' doc='Display the session command history' />
      </params>
    </command>
    <command id='log stderr'>
      <params>
        <param name='log' doc='Configure logging sub-system' />
        <param name='stderr' doc='Logging via STDERR of the process' />
      </params>
    </command>
    <command id='no log stderr'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='log' doc='Configure logging sub-system' />
        <param name='stderr' doc='Logging via STDERR of the process' />
      </params>
    </command>
    <command id='log file .FILENAME'>
      <params>
        <param name='log' doc='Configure logging sub-system' />
        <param name='file' doc='Logging to text file' />
        <param name='.FILENAME' doc='Filename' />
      </params>
    </command>
    <command id='no log file .FILENAME'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='log' doc='Configure logging sub-system' />
        <param name='file' doc='Logging to text file' />
        <param name='.FILENAME' doc='Filename' />
      </params>
    </command>
    <command id='log alarms &lt;2-32700&gt;'>
      <params>
        <param name='log' doc='Configure logging sub-system' />
        <param name='alarms' doc='Logging alarms to osmo_strrb' />
        <param name='&lt;2-32700&gt;' doc='Maximum number of messages to log' />
      </params>
    </command>
    <command id='no log alarms'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='log' doc='Configure logging sub-system' />
        <param name='alarms' doc='Logging alarms to osmo_strrb' />
      </params>
    </command>
    <command id='log syslog (authpriv|cron|daemon|ftp|lpr|mail|news|user|uucp)'>
      <params>
        <param name='log' doc='Configure logging sub-system' />
        <param name='syslog' doc='Logging via syslog' />
        <param name='authpriv' doc='Security/authorization messages facility' />
        <param name='cron' doc='Clock daemon (cron/at) facility' />
        <param name='daemon' doc='General system daemon facility' />
        <param name='ftp' doc='Ftp daemon facility' />
        <param name='lpr' doc='Line printer facility' />
        <param name='mail' doc='Mail facility' />
        <param name='news' doc='News facility' />
        <param name='user' doc='Generic facility' />
        <param name='uucp' doc='UUCP facility' />
      </params>
    </command>
    <command id='log syslog local &lt;0-7&gt;'>
      <params>
        <param name='log' doc='Configure logging sub-system' />
        <param name='syslog' doc='Logging via syslog' />
        <param name='local' doc='Syslog LOCAL facility' />
        <param name='&lt;0-7&gt;' doc='Local facility number' />
      </params>
    </command>
    <command id='no log syslog'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='log' doc='Configure logging sub-system' />
        <param name='syslog' doc='Logging via syslog' />
      </params>
    </command>
    <command id='log gsmtap [HOSTNAME]'>
      <params>
        <param name='log' doc='Configure logging sub-system' />
        <param name='gsmtap' doc='Logging via GSMTAP' />
        <param name='[HOSTNAME]' doc='Host name to send the GSMTAP logging to (UDP port 4729)' />
      </params>
    </command>
    <command id='stats reporter statsd'>
      <params>
        <param name='stats' doc='Configure stats sub-system' />
        <param name='reporter' doc='Configure a stats reporter' />
        <param name='statsd' doc='Report to a STATSD server' />
      </params>
    </command>
    <command id='no stats reporter statsd'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='stats' doc='Configure stats sub-system' />
        <param name='reporter' doc='Configure a stats reporter' />
        <param name='statsd' doc='Report to a STATSD server' />
      </params>
    </command>
    <command id='stats reporter log'>
      <params>
        <param name='stats' doc='Configure stats sub-system' />
        <param name='reporter' doc='Configure a stats reporter' />
        <param name='log' doc='Report to the logger' />
      </params>
    </command>
    <command id='no stats reporter log'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='stats' doc='Configure stats sub-system' />
        <param name='reporter' doc='Configure a stats reporter' />
        <param name='log' doc='Report to the logger' />
      </params>
    </command>
    <command id='stats interval &lt;1-65535&gt;'>
      <params>
        <param name='stats' doc='Configure stats sub-system' />
        <param name='interval' doc='Set the reporting interval' />
        <param name='&lt;1-65535&gt;' doc='Interval in seconds' />
      </params>
    </command>
    <command id='ggsn NAME'>
      <params>
        <param name='ggsn' doc='Configure the Gateway GPRS Support Node' />
        <param name='NAME' doc='GGSN Name (has only local significance)' />
      </params>
    </command>
    <command id='no ggsn NAME'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='ggsn' doc='Remove the named Gateway GPRS Support Node' />
        <param name='NAME' doc='GGSN Name (has only local significance)' />
      </params>
    </command>
    <command id='ctrl'>
      <params>
        <param name='ctrl' doc='Configure the Control Interface' />
      </params>
    </command>
  </node>
  <node id='config-log'>
    <name>config-log</name>
    <command id='logging filter all (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='filter' doc='Filter log messages' />
        <param name='all' doc='Do you want to log all messages?' />
        <param name='0' doc='Only print messages matched by other filters' />
        <param name='1' doc='Bypass filter and print all messages' />
      </params>
    </command>
    <command id='logging color (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='color' doc='Configure color-printing for log messages' />
        <param name='0' doc='Don&apos;t use color for printing messages' />
        <param name='1' doc='Use color for printing messages' />
      </params>
    </command>
    <command id='logging timestamp (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='timestamp' doc='Configure log message timestamping' />
        <param name='0' doc='Don&apos;t prefix each log message' />
        <param name='1' doc='Prefix each log message with current timestamp' />
      </params>
    </command>
    <command id='logging print extended-timestamp (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='print' doc='Log output settings' />
        <param name='extended-timestamp' doc='Configure log message timestamping' />
        <param name='0' doc='Don&apos;t prefix each log message' />
        <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
      </params>
    </command>
    <command id='logging print category (0|1)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='print' doc='Log output settings' />
        <param name='category' doc='Configure log message' />
        <param name='0' doc='Don&apos;t prefix each log message' />
        <param name='1' doc='Prefix each log message with category/subsystem name' />
      </params>
    </command>
    <command id='logging set-log-mask MASK'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='set-log-mask' doc='Set the logmask of this logging target' />
        <param name='MASK' doc='List of logging categories to log, e.g. &apos;abc:mno:xyz&apos;. Available log categories depend on the specific application, refer to the &apos;logging level&apos; command. Optionally add individual log levels like &apos;abc,1:mno,3:xyz,5&apos;, where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' />
      </params>
    </command>
    <command id='logging level (all|ip|tun|ggsn|sgsn|icmp6|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp) (everything|debug|info|notice|error|fatal)'>
      <params>
        <param name='logging' doc='Configure logging' />
        <param name='level' doc='Set the log level for a specified category' />
        <param name='all' doc='Global setting for all subsystems' />
        <param name='ip' doc='IP Pool and other groups' />
        <param name='tun' doc='Tunnel interface' />
        <param name='ggsn' doc='GGSN' />
        <param name='sgsn' doc='SGSN Emulator' />
        <param name='icmp6' doc='ICMPv6' />
        <param name='lglobal' doc='Library-internal global log family' />
        <param name='llapd' doc='LAPD in libosmogsm' />
        <param name='linp' doc='A-bis Intput Subsystem' />
        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
        <param name='lmi' doc='A-bis Input Driver for Signalling' />
        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
        <param name='lctrl' doc='Control Interface' />
        <param name='lgtp' doc='GPRS GTP library' />
        <param name='lstats' doc='Statistics messages and logging' />
        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
        <param name='loap' doc='Osmocom Authentication Protocol' />
        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
        <param name='everything' doc='Don&apos;t use. It doesn&apos;t log anything' />
        <param name='debug' doc='Log debug messages and higher levels' />
        <param name='info' doc='Log informational messages and higher levels' />
        <param name='notice' doc='Log noticeable messages and higher levels' />
        <param name='error' doc='Log error messages and higher levels' />
        <param name='fatal' doc='Log only fatal messages' />
      </params>
    </command>
  </node>
  <node id='config-stats'>
    <name>config-stats</name>
    <command id='local-ip ADDR'>
      <params>
        <param name='local-ip' doc='Set the IP address to which we bind locally' />
        <param name='ADDR' doc='IP Address' />
      </params>
    </command>
    <command id='no local-ip'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='local-ip' doc='Set the IP address to which we bind locally' />
      </params>
    </command>
    <command id='remote-ip ADDR'>
      <params>
        <param name='remote-ip' doc='Set the remote IP address to which we connect' />
        <param name='ADDR' doc='IP Address' />
      </params>
    </command>
    <command id='remote-port &lt;1-65535&gt;'>
      <params>
        <param name='remote-port' doc='Set the remote port to which we connect' />
        <param name='&lt;1-65535&gt;' doc='Remote port number' />
      </params>
    </command>
    <command id='mtu &lt;100-65535&gt;'>
      <params>
        <param name='mtu' doc='Set the maximum packet size' />
        <param name='&lt;100-65535&gt;' doc='Size in byte' />
      </params>
    </command>
    <command id='no mtu'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='mtu' doc='Set the maximum packet size' />
      </params>
    </command>
    <command id='prefix PREFIX'>
      <params>
        <param name='prefix' doc='Set the item name prefix' />
        <param name='PREFIX' doc='The prefix string' />
      </params>
    </command>
    <command id='no prefix'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='prefix' doc='Set the item name prefix' />
      </params>
    </command>
    <command id='level (global|peer|subscriber)'>
      <params>
        <param name='level' doc='Set the maximum group level' />
        <param name='global' doc='Report global groups only' />
        <param name='peer' doc='Report global and network peer related groups' />
        <param name='subscriber' doc='Report global, peer, and subscriber groups' />
      </params>
    </command>
    <command id='enable'>
      <params>
        <param name='enable' doc='Enable the reporter' />
      </params>
    </command>
    <command id='disable'>
      <params>
        <param name='disable' doc='Disable the reporter' />
      </params>
    </command>
  </node>
  <node id='config-line'>
    <name>config-line</name>
    <command id='login'>
      <params>
        <param name='login' doc='Enable password checking' />
      </params>
    </command>
    <command id='no login'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='login' doc='Enable password checking' />
      </params>
    </command>
    <command id='bind A.B.C.D'>
      <params>
        <param name='bind' doc='Accept VTY telnet connections on local interface' />
        <param name='A.B.C.D' doc='Local interface IP address (default: 127.0.0.1)' />
      </params>
    </command>
  </node>
  <node id='config-ctrl'>
    <name>config-ctrl</name>
    <command id='bind A.B.C.D'>
      <params>
        <param name='bind' doc='Set bind address to listen for Control connections' />
        <param name='A.B.C.D' doc='Local IP address (default 127.0.0.1)' />
      </params>
    </command>
  </node>
  <node id='config-ggsn'>
    <name>config-ggsn</name>
    <command id='description .TEXT'>
      <params>
        <param name='description' doc='Save human-readable description of the object' />
        <param name='.TEXT' doc='Text until the end of the line' />
      </params>
    </command>
    <command id='no description'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='description' doc='Remove description of the object' />
      </params>
    </command>
    <command id='shutdown ggsn'>
      <params>
        <param name='shutdown' doc='Put the GGSN in administrative shut-down' />
        <param name='ggsn' doc='Gateway GPRS Support NODE (GGSN)' />
      </params>
    </command>
    <command id='no shutdown ggsn'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='shutdown' doc='Gateway GPRS Support NODE (GGSN)' />
        <param name='ggsn' doc='Remove the GGSN from administrative shut-down' />
      </params>
    </command>
    <command id='gtp bind-ip A.B.C.D'>
      <params>
        <param name='gtp' doc='GTP Parameters' />
        <param name='bind-ip' doc='Set the IP address for the local GTP bind' />
        <param name='A.B.C.D' doc='IPv4 Address' />
      </params>
    </command>
    <command id='gtp control-ip A.B.C.D'>
      <params>
        <param name='gtp' doc='GTP Parameters' />
        <param name='control-ip' doc='Set the IP address states as local IP in GTP-C messages' />
        <param name='A.B.C.D' doc='IPv4 Address' />
      </params>
    </command>
    <command id='gtp user-ip A.B.C.D'>
      <params>
        <param name='gtp' doc='GTP Parameters' />
        <param name='user-ip' doc='Set the IP address states as local IP in GTP-U messages' />
        <param name='A.B.C.D' doc='IPv4 Address' />
      </params>
    </command>
    <command id='gtp state-dir PATH'>
      <params>
        <param name='gtp' doc='GTP Parameters' />
        <param name='state-dir' doc='Set the directory for the GTP State file' />
        <param name='PATH' doc='Local Directory' />
      </params>
    </command>
    <command id='apn NAME'>
      <params>
        <param name='apn' doc='APN Configuration' />
        <param name='NAME' doc='APN Name' />
      </params>
    </command>
    <command id='no apn NAME'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='apn' doc='Remove APN Configuration' />
        <param name='NAME' doc='APN Name' />
      </params>
    </command>
    <command id='default-apn NAME'>
      <params>
        <param name='default-apn' doc='Set a default-APN to be used if no other APN matches' />
        <param name='NAME' doc='APN Name' />
      </params>
    </command>
    <command id='no default-apn'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='default-apn' doc='Remove default-APN to be used if no other APN matches' />
      </params>
    </command>
  </node>
  <node id='config-ggsn-apn'>
    <name>config-ggsn-apn</name>
    <command id='description .TEXT'>
      <params>
        <param name='description' doc='Save human-readable description of the object' />
        <param name='.TEXT' doc='Text until the end of the line' />
      </params>
    </command>
    <command id='no description'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='description' doc='Remove description of the object' />
      </params>
    </command>
    <command id='shutdown'>
      <params>
        <param name='shutdown' doc='Put the APN in administrative shut-down' />
      </params>
    </command>
    <command id='no shutdown'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='shutdown' doc='Remove the APN from administrative shut-down' />
      </params>
    </command>
    <command id='gtpu-mode (tun|kernel-gtp)'>
      <params>
        <param name='gtpu-mode' doc='Set the Mode for this APN (tun or Linux Kernel GTP)' />
        <param name='tun' doc='GTP-U in userspace using TUN device' />
        <param name='kernel-gtp' doc='GTP-U in kernel using Linux Kernel GTP' />
      </params>
    </command>
    <command id='type-support (v4|v6|v4v6)'>
      <params>
        <param name='type-support' doc='Enable support for PDP Type' />
        <param name='v4' doc='IPv4(-only) PDP Type' />
        <param name='v6' doc='IPv6(-only) PDP Type' />
        <param name='v4v6' doc='IPv4v6 (dual-stack) PDP Type' />
      </params>
    </command>
    <command id='no type-support (v4|v6|v4v6)'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='type-support' doc='Disable support for PDP Type' />
        <param name='v4' doc='IPv4(-only) PDP Type' />
        <param name='v6' doc='IPv6(-only) PDP Type' />
        <param name='v4v6' doc='IPv4v6 (dual-stack) PDP Type' />
      </params>
    </command>
    <command id='tun-device NAME'>
      <params>
        <param name='tun-device' doc='Configure tun device name' />
        <param name='NAME' doc='TUN device name' />
      </params>
    </command>
    <command id='ipup-script PATH'>
      <params>
        <param name='ipup-script' doc='Configure name/path of ip-up script' />
        <param name='PATH' doc='File/Path name of ip-up script' />
      </params>
    </command>
    <command id='no ipup-script'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='ipup-script' doc='Disable ip-up script' />
      </params>
    </command>
    <command id='ipdown-script PATH'>
      <params>
        <param name='ipdown-script' doc='Configure name/path of ip-down script' />
        <param name='PATH' doc='File/Path name of ip-down script' />
      </params>
    </command>
    <command id='no ipdown-script'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='ipdown-script' doc='Disable ip-down script' />
      </params>
    </command>
    <command id='ip prefix (static|dynamic) A.B.C.D/M'>
      <params>
        <param name='ip' doc='IP information' />
        <param name='prefix' doc='Prefix (Network/Netmask)' />
        <param name='static' doc='IPv4 Adress/Prefix-Length' />
        <param name='dynamic' doc='(null)' />
        <param name='A.B.C.D/M' doc='(null)' />
      </params>
    </command>
    <command id='ipv6 prefix (static|dynamic) X:X::X:X/M'>
      <params>
        <param name='ipv6' doc='IPv6 Information' />
        <param name='prefix' doc='Prefix (Network/Netmask)' />
        <param name='static' doc='IPv6 Address/Prefix-Length' />
        <param name='dynamic' doc='(null)' />
        <param name='X:X::X:X/M' doc='(null)' />
      </params>
    </command>
    <command id='ip dns &lt;0-1&gt; A.B.C.D'>
      <params>
        <param name='ip' doc='IP information' />
        <param name='dns' doc='Configure DNS Server' />
        <param name='&lt;0-1&gt;' doc='primary/secondary DNS' />
        <param name='A.B.C.D' doc='IP address of DNS Sever' />
      </params>
    </command>
    <command id='ipv6 dns &lt;0-1&gt; X:X::X:X'>
      <params>
        <param name='ipv6' doc='IPv6 Information' />
        <param name='dns' doc='Configure DNS Server' />
        <param name='&lt;0-1&gt;' doc='primary/secondary DNS' />
        <param name='X:X::X:X' doc='IP address of DNS Sever' />
      </params>
    </command>
    <command id='no (ip|ipv6) dns &lt;0-1&gt;'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='ip' doc='IP information' />
        <param name='ipv6' doc='IPv6 Information' />
        <param name='dns' doc='Disable DNS Server' />
        <param name='&lt;0-1&gt;' doc='primary/secondary DNS' />
      </params>
    </command>
    <command id='ip ifconfig A.B.C.D/M'>
      <params>
        <param name='ip' doc='IP information' />
        <param name='ifconfig' doc='GGSN-based interface configuration' />
        <param name='A.B.C.D/M' doc='IPv4 Adress/Prefix-Length' />
      </params>
    </command>
    <command id='no ip ifconfig'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='ip' doc='IP information' />
        <param name='ifconfig' doc='GGSN-based interface configuration' />
      </params>
    </command>
    <command id='ipv6 ifconfig X:X::X:X/M'>
      <params>
        <param name='ipv6' doc='IPv6 Information' />
        <param name='ifconfig' doc='GGSN-based interface configuration' />
        <param name='X:X::X:X/M' doc='IPv6 Adress/Prefix-Length' />
      </params>
    </command>
    <command id='no ipv6 ifconfig'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='ipv6' doc='IPv6 Information' />
        <param name='ifconfig' doc='GGSN-based interface configuration' />
      </params>
    </command>
    <command id='g-pdu tx-sequence-numbers'>
      <params>
        <param name='g-pdu' doc='G-PDU Configuration' />
        <param name='tx-sequence-numbers' doc='Enable transmission of G-PDU sequence numbers' />
      </params>
    </command>
    <command id='no g-pdu tx-sequence-numbers'>
      <params>
        <param name='no' doc='Negate a command or set its defaults' />
        <param name='g-pdu' doc='G-PDU Configuration' />
        <param name='tx-sequence-numbers' doc='Disable transmission of G-PDU sequence numbers' />
      </params>
    </command>
  </node>
</vtydoc>