| ############################################################################## |
| # |
| # Sample sgsnemu configuration file |
| # |
| ############################################################################## |
| |
| # TAG: fg |
| # Include this flag if process is to run in the foreground |
| # |
| fg |
| |
| # TAG: debug |
| # Include this flag to include debug information. |
| #debug |
| |
| |
| # TAG: conf |
| # Configuration file to use. This file is the configuration file, |
| # so changing this parameter in the configuration file does not make |
| # sense. Use it on the command line instead. |
| |
| # TAG: pidfile |
| # File to store information about the pricess id of the program. |
| # The program must have write access to this file/directory. |
| #pidfile ./sgsnemu.pid |
| |
| # TAG: statedir |
| # Directory to use for nonvolatile storage. |
| # The program must have write access to this directory. |
| #statedir ./ |
| |
| |
| # TAG: dns |
| # DNS server to use for ns lookups. |
| # If this tag is not set the system default DNS will be used. |
| #dns 10.1.2.3 |
| |
| # TAG: listen |
| # Specifies the local IP address to listen to |
| listen 10.0.0.217 |
| |
| # TAG: remote |
| # Specifies the remote IP address to connect to |
| # If DNS is setup correctly it should be possible to specify the |
| # access point name (APN) as the remote address. |
| remote 10.0.0.240 |
| |
| # TAG: contexts |
| # Number of contexts to establish from the emulator to the ggsn. |
| # Set this tag to zero to not establish any contexts. |
| #contexts 1 |
| |
| # TAG: timelimit |
| # Disconnect contexts after timelimit seconds, and exit the program. |
| # Setting timelimit to zero will cause the program not to disconnect. |
| #timelimit 0 |
| |
| |
| # TAG: apn |
| # Access point name to connect to when run in client mode. |
| #apn internet |
| |
| # TAG: imsi |
| # IMSI number used when run in client mode. |
| #imsi 2400101234567890 |
| |
| # TAG: msisdn |
| # MSISDN number used when run in client mode. |
| #msisdn 46702123456 |
| |
| # TAG: qos |
| # Requested Quality of Service used when run in client mode. |
| # 3 bytes corresponding to ???? |
| #qos 0x0b921f |
| |
| # TAG: uid |
| # User ID used when run in client mode. |
| #uid mig |
| |
| # TAG: pwd |
| # Password used when run in client mode. |
| #pwd hemlig |
| |
| |
| # TAG: createif |
| # Use this flag if you want to set up a local network interface after |
| # a PDP context has been established. |
| #createif |
| |
| # TAG: defaultroute |
| # Use this flag if you want to add a default route after a network interface |
| # had been established. |
| #defaultroute |
| |
| # TAG: ipup |
| # Script executed after network interface has been brought up. |
| # Executed with the following parameters: <devicename> <ip address> |
| #ipup /etc/sgsnemu/ip-up |
| |
| # TAG: ipdown |
| # Script executed after network interface has been taken down. |
| # Executed with the following parameters: <devicename> <ip address> |
| #ipdown /etc/sgsnemu/ip-down |
| |
| # TAG: pinghost |
| # Ping a remote host through a PDP context by using ICMP echo messages. |
| # If more than one PDP context has been established the ICMP messages will |
| # be distributed between all available contexts. |
| #pinghost 192.168.0.0 |
| |
| # TAG: pingrate |
| # Number of ping messages to send off each second. |
| #pingrate 1 |
| |
| # TAG: pingsize |
| # Size of ICMP echo message payload. Add 28 to get the full IP packet size. |
| #pingsize 56 |
| |
| # TAG: pingcount |
| # Number of ping messages to send off. |
| #pingcount 0 |
| |
| # TAG: pingquiet |
| # Do not print ping packet info. |
| #pingquiet |
| |
| |
| |
| |
| |