Harald Welte | 9f1331b | 2016-02-20 10:56:10 +0100 | [diff] [blame^] | 1 | <vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'> |
| 2 | <node id='21'> |
| 3 | <child_of nodeid='4' /> |
| 4 | <name>SGSN Configuration Node</name> |
| 5 | <description>Configure the remote GGSN, access-control and other |
| 6 | attributes of the SGSN</description> |
| 7 | <command id='gtp local-ip A.B.C.D'> |
| 8 | <description> |
| 9 | Configure the local IP address to which the SGSN should |
| 10 | bind for the Gp interface (towards the GGSNs). |
| 11 | |
| 12 | Please note that in case you would like to run the GGSN |
| 13 | on the same machine as the SGSN, you can not run both on |
| 14 | the same IP address. It is suggested to use 127.0.0.1 |
| 15 | for the SGSN and 127.0.0.2 for the GGSN in such |
| 16 | situations. |
| 17 | </description> |
| 18 | </command> |
| 19 | <command id='ggsn <0-255> remote-ip A.B.C.D'> |
| 20 | <description> |
| 21 | Configure a static GGSN with a given numeric identifier |
| 22 | to use the specified remote IP address. |
| 23 | </description> |
| 24 | </command> |
| 25 | <command id='ggsn <0-255> gtp-version (0|1)'> |
| 26 | <description> |
| 27 | Configure whether to use GTPv0 or GTPv1 towards the |
| 28 | specified GSSN number. |
| 29 | </description> |
| 30 | </command> |
| 31 | <command id='ggsn dynamic'> |
| 32 | <description> |
| 33 | Enable dynamic resolving of GGSNs based on DNS resolving |
| 34 | the APN name like in a GRX-style setup. Changing this |
| 35 | setting requires a re-start of the SGSN. |
| 36 | </description> |
| 37 | </command> |
| 38 | <command id='grx-dns-add A.B.C.D'> |
| 39 | <description> |
| 40 | Use the specified IP address for DNS-resolving the AP |
| 41 | names to GGSN IP addresses |
| 42 | </description> |
| 43 | </command> |
| 44 | <command id='apn APNAME ggsn <0-255>'> |
| 45 | <description> |
| 46 | Map the given APN Name to the given GGSN number. |
| 47 | </description> |
| 48 | </command> |
| 49 | <command id='apn APNAME imsi-prefx IMSIPRE ggsn <0-255>'> |
| 50 | <description> |
| 51 | Map the given APN Name to the given GGSN number _only_ |
| 52 | if the IMSI matches the given prefix. |
| 53 | </description> |
| 54 | </command> |
| 55 | <command id='imsi-acl (add|del) IMSI'> |
| 56 | <description> |
| 57 | Add or delete the given IMSI to/from the global Access |
| 58 | Control List. |
| 59 | </description> |
| 60 | </command> |
| 61 | <command id='auth-policy (accept-all|closed|acl-only|remote)'> |
| 62 | <description> |
| 63 | Configure the Authorization policy of the SGSN. This |
| 64 | setting determines which subscribers are permitted to |
| 65 | register to the network. |
| 66 | </description> |
| 67 | </command> |
| 68 | <command id='gsup remote-ip A.B.C.D'> |
| 69 | <description> |
| 70 | Set the IP address of the HLR (gateway) for the GSUP protocol. |
| 71 | This setting only applies if auth-policy remote is used. |
| 72 | </description> |
| 73 | </command> |
| 74 | <command id='gsup oap-id <0-65535>'> |
| 75 | <description> |
| 76 | Set the OAP client ID for authentication on the GSUP |
| 77 | protocol. |
| 78 | This setting only applies if auth-policy remote is used. |
| 79 | </description> |
| 80 | </command> |
| 81 | <command id='gsup oap-k K'> |
| 82 | <description> |
| 83 | Set the OAP shared secret key K for authentication on |
| 84 | the GSUP protocol. |
| 85 | This setting only applies if auth-policy remote is used. |
| 86 | </description> |
| 87 | </command> |
| 88 | <command id='gsup oap-opc OPC'> |
| 89 | <description> |
| 90 | Set the OAP shared secret OPC for authentication on the |
| 91 | GSUP protocol. |
| 92 | This setting only applies if auth-policy remote is used. |
| 93 | </description> |
| 94 | </command> |
| 95 | <command id='access-point-name NAME'> |
| 96 | <description> |
| 97 | Globally allow the given APN name for all subscribers. |
| 98 | </description> |
| 99 | </command> |
| 100 | <command id='cdr filename NAME'> |
| 101 | <description> |
| 102 | Set the file name for the call-data-record file, |
| 103 | logging the data usage of each subscriber. |
| 104 | </description> |
| 105 | </command> |
| 106 | <command id='cdr interval <1-2147483647>'> |
| 107 | <description> |
| 108 | Set the interval (in secodnds) for the call-data-record |
| 109 | file. |
| 110 | </description> |
| 111 | </command> |
| 112 | </node> |
| 113 | </vtydoc> |