- ff394bd e1-tracer: commit a first schematic by Martin Schramm · 3 years, 10 months ago
- 190cd58 increase clearance of ground planes; pad roundness by Harald Welte · 4 years, 5 months ago
- c5a57a2 enlarge board to have proper mounting holes for mechanical mounting by Harald Welte · 4 years, 5 months ago
- dfe01d4 squash most parts and avoid silk screen overlaps all over the place by Harald Welte · 4 years, 5 months ago
- 2a8c4c5 change font to vector / update to v2 by Harald Welte · 4 years, 5 months ago
- 15e6f9a e1_xcvr.brd: minor routing improvement on TRING signal by Martin Schramm · 6 years ago
- 00ebf25 replace old PULSE_T1094NL footprint, repair pin assignment (solves OSM#3269) by Martin Schramm · 6 years ago
- 8ce5748 laforge.lbr: PULSE_T1094NL: better tPlace and tDocu layer (for OSM#3270) by Martin Schramm · 6 years ago
- 69f96a6 connect LIU's pin 44 to GND (solves OSM#3247) by Martin Schramm · 6 years ago
- ed2b563 laforge.lbr: repair PULSE_T1094NL footprint and symbol (solves OSM#3270) by Martin Schramm · 6 years ago
- e00749c sam4s-e1.gnumeric: Avoid EXT4, add wire colors by Harald Welte · 6 years ago
- d373558 src: Add .gitignore for the software by Sylvain Munaut · 6 years ago
- 2c3c275 osmo_e1f: Fix Makefile to use pkg-config by Sylvain Munaut · 6 years ago
- a3ddfb1 Merge branch 'laforge/software' by Harald Welte · 6 years ago
- 24531ce rename osmo_e1 to osmo_e1f ("f" for "framer") by Harald Welte · 6 years ago
- 82fb9b7 osmo_e1: fix make clean by Harald Welte · 6 years ago
- cdbcff9 CRC4: use proper CRC4 table to avoid bit-reversal of each byte by Harald Welte · 6 years ago
- ce18a04 add e1_test_dieter to deframe/decode dieters capture by Harald Welte · 6 years ago
- 8a95fd5 osmo_e1: Add HDLC framing/deframing by Harald Welte · 6 years ago
- 37e2374 osmo_e1: Silence the FSM logging by Harald Welte · 6 years ago
- 9bd2c9f HACK to make CRC4 computation work by Harald Welte · 6 years ago
- d3941c6 osmo_e1.c: Fix handling of TS2..31 (use 'i', not '1') by Harald Welte · 6 years ago
- f01471d add some information related a SAM4S based USB-to-LIU adapter board idea by Harald Welte · 6 years ago
- 0c756eb WIP: Software for E1 mux/demux by Harald Welte · 6 years ago
- 5b15f68 add E1 tap hardware design by Harald Welte · 12 years ago
- ceb6ef1 laforge.lbr: fix amphenol sim reader footprint by Harald Welte · 12 years ago
- b59bfbc major update of laforge.lbr with lots of new components by Harald Welte · 12 years ago
- 605e3e4 add some glue code between the idt82 driver and at91lib SPI by Harald Welte · 12 years ago
- 638afbb 'new' PCB routing by Christian Vogel by Harald Welte · 12 years ago
- 28460ee major update of laforge.lbr with lots of new components by Harald Welte · 12 years ago
- da02f55 add initial driver skeleton for idt82v2081 chip by Harald Welte · 12 years ago
- ceb70a8 give parts names without "$", use 47nH as L1 (1206) by Harald Welte · 12 years ago
- b8dfc48 approve lots of warnings about thinner wires by Harald Welte · 12 years ago
- 71ba939 remove stray GNDIO wire, add junction, approve some warnings by Harald Welte · 12 years ago
- 5becd7e re-route complete board, add PWR jumper, LED series resistor by Christian Vogel · 12 years ago
- a40a482 add partlist/bom by Harald Welte · 12 years ago
- 372a183 update schematics and PCB layout by Harald Welte · 12 years ago
- 07c856a re-route pcb with LEDs by Harald Welte · 12 years ago
- f687f38 add two LEDs (power and LOS) plus required transistor by Harald Welte · 12 years ago
- a2c23eb re-route the entire board to add test pads and additional components by Harald Welte · 12 years ago
- 8b0e886 just name some signals/networks by Harald Welte · 12 years ago
- 311b277 add solder jumper to bypass TPS736XX (if it is not populated) by Harald Welte · 12 years ago
- df93fb1 add 4 test pads for RTIP/RRING/TTIP/TRING by Harald Welte · 12 years ago
- e5fd58a re-wire SPI connector to reflect pin-out of Olimex devel board UEXT by Harald Welte · 12 years ago
- f4a1d02 Add LDO, remove jumpers, 3nd RJ45, ... by Harald Welte · 12 years ago
- 2f4c472 add README file by Harald Welte · 12 years ago
- 547bc5c initial checkin by Harald Welte · 12 years ago