| Sylvain Munaut | bd83e53 | 2020-09-15 22:11:29 +0200 | [diff] [blame] | 1 | # E1 PHY |
| 2 | set_io e1A_rx_hi_p 42 |
| 3 | set_io e1A_rx_hi_n 38 |
| 4 | set_io e1A_rx_lo_p 32 |
| 5 | set_io e1A_rx_lo_n 31 |
| 6 | set_io e1A_tx_hi 43 |
| 7 | set_io e1A_tx_lo 36 |
| 8 | |
| 9 | set_io e1B_rx_hi_p 23 |
| 10 | set_io e1B_rx_hi_n 25 |
| 11 | set_io e1B_rx_lo_p 26 |
| 12 | set_io e1B_rx_lo_n 27 |
| 13 | set_io e1B_tx_hi 34 |
| 14 | set_io e1B_tx_lo 37 |
| 15 | |
| 16 | set_io e1_rx_bias[0] 28 |
| 17 | set_io e1_rx_bias[1] 35 |
| 18 | |
| 19 | # USB |
| 20 | set_io usb_dp 10 |
| 21 | set_io usb_dn 9 |
| 22 | set_io usb_pu 11 |
| 23 | |
| 24 | # Flash |
| 25 | set_io -pullup yes flash_mosi 14 |
| 26 | set_io -pullup yes flash_miso 17 |
| 27 | set_io -pullup yes flash_clk 15 |
| 28 | set_io -pullup yes flash_cs_n 16 |
| 29 | |
| 30 | # LED Shift register + Button input |
| 31 | set_io -pullup yes e1_led_rclk 18 |
| 32 | |
| 33 | # GPS |
| 34 | set_io -pullup yes gps_reset_n 6 |
| 35 | set_io -pullup yes gps_rx 47 |
| 36 | set_io -pullup yes gps_tx 46 |
| 37 | set_io gps_pps 2 |
| 38 | |
| 39 | # I2C |
| 40 | set_io i2c_sda 3 |
| 41 | set_io i2c_scl 4 |
| 42 | |
| 43 | # GPIOs |
| 44 | set_io -pullup yes gpio[0] 13 |
| 45 | set_io -pullup yes gpio[1] 20 |
| 46 | set_io -pullup yes gpio[2] 19 |
| 47 | |
| 48 | # Clock |
| 49 | set_io clk_in 44 |
| 50 | |
| 51 | set_io clk_tune_hi 48 |
| 52 | set_io clk_tune_lo 45 |
| 53 | |
| 54 | # Debug UART |
| 55 | set_io -pullup yes dbg_rx 21 |
| 56 | set_io -pullup yes dbg_tx 12 |
| 57 | |
| 58 | # RGB LEDs |
| 59 | set_io rgb[0] 39 |
| 60 | set_io rgb[1] 40 |
| 61 | set_io rgb[2] 41 |