| /** |
| * \file |
| * |
| * \brief USART related functionality declaration. |
| * |
| * Copyright (c) 2014-2018 Microchip Technology Inc. and its subsidiaries. |
| * |
| * \asf_license_start |
| * |
| * \page License |
| * |
| * Subject to your compliance with these terms, you may use Microchip |
| * software and any derivatives exclusively with Microchip products. |
| * It is your responsibility to comply with third party license terms applicable |
| * to your use of third party software (including open source software) that |
| * may accompany Microchip software. |
| * |
| * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, |
| * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, |
| * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, |
| * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE |
| * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL |
| * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE |
| * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE |
| * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT |
| * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY |
| * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, |
| * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE. |
| * |
| * \asf_license_stop |
| * |
| */ |
| |
| #ifndef _HAL_SYNC_USART_H_INCLUDED |
| #define _HAL_SYNC_USART_H_INCLUDED |
| |
| #include "hal_io.h" |
| #include <hpl_usart_sync.h> |
| |
| /** |
| * \addtogroup doc_driver_hal_usart_sync |
| * |
| * @{ |
| */ |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /** |
| * \brief Synchronous USART descriptor |
| */ |
| struct usart_sync_descriptor { |
| struct io_descriptor io; |
| struct _usart_sync_device device; |
| }; |
| |
| /** |
| * \brief Initialize USART interface |
| * |
| * This function initializes the given I/O descriptor to be used |
| * as USART interface descriptor. |
| * It checks if the given hardware is not initialized and |
| * if the given hardware is permitted to be initialized. |
| * |
| * \param[out] descr A USART descriptor which is used to communicate via USART |
| * \param[in] hw The pointer to hardware instance |
| * \param[in] func The pointer to as set of functions pointers |
| * |
| * \return Initialization status. |
| */ |
| int32_t usart_sync_init(struct usart_sync_descriptor *const descr, void *const hw, void *const func); |
| |
| /** |
| * \brief Deinitialize USART interface |
| * |
| * This function deinitializes the given I/O descriptor. |
| * It checks if the given hardware is initialized and |
| * if the given hardware is permitted to be deinitialized. |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * |
| * \return De-initialization status. |
| */ |
| int32_t usart_sync_deinit(struct usart_sync_descriptor *const descr); |
| |
| /** |
| * \brief Enable USART interface |
| * |
| * Enables the USART interface |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * |
| * \return Enabling status. |
| */ |
| int32_t usart_sync_enable(struct usart_sync_descriptor *const descr); |
| |
| /** |
| * \brief Disable USART interface |
| * |
| * Disables the USART interface |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * |
| * \return Disabling status. |
| */ |
| int32_t usart_sync_disable(struct usart_sync_descriptor *const descr); |
| |
| /** |
| * \brief Retrieve I/O descriptor |
| * |
| * This function retrieves the I/O descriptor of the given USART descriptor. |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * \param[out] io An I/O descriptor to retrieve |
| * |
| * \return The status of the I/O descriptor retrieving. |
| */ |
| int32_t usart_sync_get_io_descriptor(struct usart_sync_descriptor *const descr, struct io_descriptor **io); |
| |
| /** |
| * \brief Specify action for flow control pins |
| * |
| * This function sets the action (or state) for the flow control pins |
| * if the flow control is enabled. |
| * It sets the state of flow control pins only if the automatic support of |
| * the flow control is not supported by the hardware. |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * \param[in] state A state to set the flow control pins |
| * |
| * \return The status of flow control action setup. |
| */ |
| int32_t usart_sync_set_flow_control(struct usart_sync_descriptor *const descr, |
| const union usart_flow_control_state state); |
| |
| /** |
| * \brief Set USART baud rate |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * \param[in] baud_rate A baud rate to set |
| * |
| * \return The status of baud rate setting. |
| */ |
| int32_t usart_sync_set_baud_rate(struct usart_sync_descriptor *const descr, const uint32_t baud_rate); |
| |
| /** |
| * \brief Set USART data order |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * \param[in] data_order A data order to set |
| * |
| * \return The status of data order setting. |
| */ |
| int32_t usart_sync_set_data_order(struct usart_sync_descriptor *const descr, const enum usart_data_order data_order); |
| |
| /** |
| * \brief Set USART mode |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * \param[in] mode A mode to set |
| * |
| * \return The status of mode setting. |
| */ |
| int32_t usart_sync_set_mode(struct usart_sync_descriptor *const descr, const enum usart_mode mode); |
| |
| /** |
| * \brief Set USART parity |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * \param[in] parity A parity to set |
| * |
| * \return The status of parity setting. |
| */ |
| int32_t usart_sync_set_parity(struct usart_sync_descriptor *const descr, const enum usart_parity parity); |
| |
| /** |
| * \brief Set USART stop bits |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * \param[in] stop_bits Stop bits to set |
| * |
| * \return The status of stop bits setting. |
| */ |
| int32_t usart_sync_set_stopbits(struct usart_sync_descriptor *const descr, const enum usart_stop_bits stop_bits); |
| |
| /** |
| * \brief Set USART character size |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * \param[in] size A character size to set |
| * |
| * \return The status of character size setting. |
| */ |
| int32_t usart_sync_set_character_size(struct usart_sync_descriptor *const descr, const enum usart_character_size size); |
| |
| /** |
| * \brief Retrieve the state of flow control pins |
| * |
| * This function retrieves the of flow control pins |
| * if the flow control is enabled. |
| * Function can return USART_FLOW_CONTROL_STATE_UNAVAILABLE in case |
| * if the flow control is done by the hardware |
| * and the pins state cannot be read out. |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * \param[out] state The state of flow control pins |
| * |
| * \return The status of flow control state reading. |
| */ |
| int32_t usart_sync_flow_control_status(const struct usart_sync_descriptor *const descr, |
| union usart_flow_control_state *const state); |
| |
| /** |
| * \brief Check if the USART transmitter is empty |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * |
| * \return The status of USART TX empty checking. |
| * \retval 0 The USART transmitter is not empty |
| * \retval 1 The USART transmitter is empty |
| */ |
| int32_t usart_sync_is_tx_empty(const struct usart_sync_descriptor *const descr); |
| |
| /** |
| * \brief Check if the USART receiver is not empty |
| * |
| * \param[in] descr A USART descriptor which is used to communicate via USART |
| * |
| * \return The status of USART RX empty checking. |
| * \retval 1 The USART receiver is not empty |
| * \retval 0 The USART receiver is empty |
| */ |
| int32_t usart_sync_is_rx_not_empty(const struct usart_sync_descriptor *const descr); |
| |
| /** |
| * \brief Retrieve the current driver version |
| * |
| * \return Current driver version. |
| */ |
| uint32_t usart_sync_get_version(void); |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| /**@}*/ |
| #endif /* _HAL_SYNC_USART_H_INCLUDED */ |