| <vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'> |
| <node id='14'> |
| <child_of nodeid='4' /> |
| <name>GSM Network Configuration</name> |
| <description>This is the base node for all configuration of |
| GSM network related configuration, it includes the LAC, CI |
| access criteria but also the configuration of each BTS in this |
| network.</description> |
| </node> |
| <node id='15'> |
| <child_of nodeid='14' /> |
| <name>BTS Configuration</name> |
| <description>This is the configuration of a single BTS.</description> |
| <command id='oml ipa stream-id <0-255> line E1_LINE'> |
| <description> |
| Set the IPA stream identifier for the OML link within the IPA |
| multiplex. Must be the same as on the BTS side. The default |
| value is 255. Only applies to BTSs connected via Abis/IP |
| interface. |
| </description> |
| </command> |
| <command id='is-connection-list (add|del) <0-2047> <0-2047> <0-255>'> |
| <description> |
| Only applies to Ericsson OML2000 based BTSs. |
| </description> |
| </command> |
| <command id='con-connection-list (add|del) <1-255> <0-1023> deconcentrated'> |
| <description> |
| Only applies to Ericsson OML2000 based BTSs. |
| </description> |
| </command> |
| <command id='con-connection-list (add|del) <1-255> <0-1023> tei <0-63>'> |
| <description> |
| Only applies to Ericsson OML2000 based BTSs. |
| </description> |
| </command> |
| <command id='channel-description attach (0|1)'> |
| <description> |
| Configure whether the IMSI ATTACH (and DETACH) procedures |
| shall be used by MS in this cell. The default should be enabled. |
| </description> |
| </command> |
| <command id='ipa rsl-ip A.B.C.D'> |
| <description> |
| Configure the IP address of the BSC used for RSL. Abis/IP |
| BTSs, including OsmoBTS and the nanoBTS will be instructed to |
| connect their RSL links to that IP address. |
| </description> |
| </command> |
| <command id='base_station_id_code <0-63>'> |
| <description> |
| Configure the BSIC of the cell. It is a 6-bit value |
| consisting of a 3-bit NCC (network color code) in the upper 3 |
| bits, and a 3-bit BCC (base station color code) in the lower 3 |
| bits. |
| </description> |
| </command> |
| <command id='training_sequence_code <0-7>'> |
| <description> |
| Configure the default TSC for all timeslots on all TRX of the BTS. |
| The normal default is to use the BCC part of the BSIC as TSC. |
| Not all BTS models support a TSC != BCC. |
| </description> |
| </command> |
| <command id='si5 neighbor-list (add|del) arfcn <0-1023>'> |
| <description> |
| Add or remove an ARFCN to/from the list of neighbor cells |
| advertised in dedicated mode via SACCH. This command is only |
| available in manual-si5 neighbor-list mode. |
| </description> |
| </command> |
| <command id='neighbor-list (add|del) arfcn <0-1023>'> |
| <description> |
| Add or remove an ARFCN to/from the list of neighbor cells. |
| This command is only available in manual neighbor-list mode. |
| </description> |
| </command> |
| <command id='gprs network-control-order (nc0|nc1|nc2)'> |
| <description> |
| </description> |
| </command> |
| <command id='cell reselection offset <0-126>'> |
| <description> |
| If a cell advertises a cell reselection offset (CRO), it will |
| become more attractive during cell re-selection, despite not |
| being received at a higher level than other cells. The CRO |
| of each neighbor cell is added to the respective received |
| signal level before comparing their values for re-selection. |
| </description> |
| </command> |
| <command id='cell reselection hysteresis <0-14>'> |
| <description> |
| The Cell Re-Selection Hysteresis determines how many dB a |
| neighbor cell must be stronger than the current serving cell |
| before the MS considers that neighbor cell as a candidate for |
| re-selection. |
| </description> |
| </command> |
| <command id='ipa unit-id <0-65534> <0-255>'> |
| <description> |
| The ip.access unit ID is a parameter of the IPA |
| Signalling-over-IP multiplex. It is administratively |
| configured on the BTS side, and used by the BTS to identify |
| itself to the BSC. The BSC then selects the BTS configuration |
| for this Unit ID. It consists of three parts, the Site ID, |
| the BTS ID and the TRX ID. The TRX ID automatically |
| corresponds to to the transceiver number and is thus not |
| configurable here. |
| </description> |
| </command> |
| <command id='ms max power <0-40>'> |
| <description> |
| Configures the maximum transmit power (in dBm) that any MS may |
| use within this cell. |
| </description> |
| </command> |
| <command id='periodic location update <6-1530>'> |
| <description> |
| The periodic location updating interval determines how often |
| the MS will periodically perform a LOCATION UPDATE procedure, |
| despite not having actuall changed location. The value is |
| specified in minutes. |
| </description> |
| </command> |
| <command id='cell barred (0|1)'> |
| <description> |
| Using this command, you can enable/disable barring of the cell. |
| Barred cells are not visible/accessible to regular phones. |
| Only some special operator testing phones can be configured in |
| a way to ignore cell barring. |
| </description> |
| </command> |
| <command id='rxlev access min <0-63>'> |
| <description> |
| Using this command, you can determine the minimum downlink |
| signal receive level (RxLev), at which the BTS must be |
| received by the MS in order to attempt establishing dedicated |
| channels via the RACH. |
| </description> |
| </command> |
| <command id='rach access-control-class (0|1|2|3|4|5|6|7|8|9|11|12|13|14|15) (barred|allowed)'> |
| <description> |
| Using this command, you can configure which access control |
| classes are permitted to access this cell. The access control |
| class of a MS is determined by the contents of the EF.ACC file |
| on the SIM card. |
| |
| Access Control Class 10 corresponds to Emergency Calls, and is |
| thus not configurable this way. |
| </description> |
| </command> |
| <command id='rach emergency call allowed (0|1)'> |
| <description> |
| Using this command, you can determine if this cell permits the |
| use of the 'EMERGENCY CALL' feature. |
| |
| <warning>Unless you operate a public network with connection to the |
| public emergency services in compliance with applicable regulatory |
| requirements, you should always have emergency calls disabled (allowed |
| 0) - which is also the default configuration.</warning> |
| </description> |
| </command> |
| <command id='channel-description bs-ag-blks-res <0-7>'> |
| <description> |
| Using this command, you can specify how many blocks of the |
| downlink CCCH should be reserved for exclusive usage as AGCH. |
| |
| <warning>Not all BTS models currently support non-default configuration |
| of this parameter.</warning> |
| </description> |
| </command> |
| <command id='oml e1 tei <0-63>'> |
| <description> |
| Set the LAPD TEI used for the OML connection of this BTS. |
| Only applies to classic E1 based A-bis. |
| </description> |
| </command> |
| </node> |
| <node id='16'> |
| <child_of nodeid='15' /> |
| <name>TRX Configuration</name> |
| <description>This is the configuration of a TRX.</description> |
| <command id='nominal power <0-100>'> |
| <description> |
| Inform the BSC about the nominal RF transmit power of the BTS in dBm. |
| This value must be entered depending on the BTS model and |
| external setup such as amplifiers. Changing this value will |
| not change the actually transmitted power, it will just affect |
| the reporting in the BSC VTY. |
| </description> |
| </command> |
| <command id='max_power_red <0-100>'> |
| <description> |
| Request the actual RF transmit power of the BTS to be reduced |
| by the specified number of dB. |
| </description> |
| </command> |
| <command id='rsl e1 tei <0-63>'> |
| <description> |
| Set the LAPD TEI used for the RSL connection of this TRX. |
| Only applies to classic E1 based A-bis. |
| </description> |
| </command> |
| <command id='rf_locked (0|1)'> |
| <description> |
| Enable (1) or disable (0) the RF locking for this TRX. RF |
| locking is a mechanism by which the transmitter can be shut |
| down by administrative means, e.g. via the control interface. |
| </description> |
| </command> |
| </node> |
| <node id='17'> |
| <child_of nodeid='16' /> |
| <name>TS Configuration</name> |
| <description>This is the configuration of a TS.</description> |
| <command id='training_sequence_code <0-7>'> |
| <description> |
| Configure the timeslot to run on a different TSC than the |
| default TSC of the BTS (which is derived from the BCC part of the BSIC). |
| Please note that not all BTS models support timeslot-specific TSC! |
| </description> |
| </command> |
| <command id='hopping enabled (0|1)'> |
| <description> |
| Enable or disable frequency hopping for this timeslot. Please |
| note that not all BTS models may support frequency hopping, |
| and that frequency hopping is only permitted for secondary |
| TRXs, so TRX 0 must always be non-hopping. |
| </description> |
| </command> |
| </node> |
| <node id='22'> |
| <child_of nodeid='3' /> |
| <name>OML Commands</name> |
| <description>This node allows to manipulate the OML state of |
| a connected BTS. It is meant for testing during development.</description> |
| </node> |
| <node id='26'> |
| <child_of nodeid='3' /> |
| <name>OML2000 Commands</name> |
| <description>This node allows to issue OML2000 commands for |
| Ericsson BTS. It is meant for testing during development.</description> |
| </node> |
| </vtydoc> |