Gitiles
Code Review
Sign In
gerrit.osmocom.org
/
simtrace2
/
c6b968067d4a2bc7a825f95e1976051d2a67ec87
/
firmware
« Previous
84ad985
usb: Cofnigure PLLB according to board.h BOARD_MAINOSC
by Harald Welte
· 8 years ago
7861132
qmod: Don't violate PLL minimum output frequency
by Harald Welte
· 8 years ago
b871363
qmod: cosmetic changes to EEPROM hex array
by Harald Welte
· 8 years ago
b30783c
qmod EEPROM: Dont't mark any ports as non-removable
by Harald Welte
· 8 years ago
ae8a465
qmod: Commit missing changes to EEPROM
by Harald Welte
· 8 years ago
6dfcf70
qmod: Start with _HUB_RESET=0 -> HUB_RESET=1 (not in reset)
by Harald Welte
· 8 years ago
f9a182d
qmod: breal the command loop when 'U' is pressed and proceed to USB init
by Harald Welte
· 8 years ago
afbb747
qmod: do not automatically clear _HUB_RESET after EEPROM write
by Harald Welte
· 8 years ago
e07aed6
qmod: debug menu: Add 'U' command to proceed to USB
by Harald Welte
· 8 years ago
396354c
qmod: debug menu: make sure to always print something
by Harald Welte
· 8 years ago
006b16d
quad-modem: Add debug console commands for debugging
by Harald Welte
· 8 years ago
e974fbb
Issue ST12_PRTPWR_OVERRIDE before putting hub in reset
by Harald Welte
· 8 years ago
15e026e
qmod: Set PIN_PRTPWR_OVERRIDE to output/low
by Harald Welte
· 8 years ago
4e3b9a5
qmod: attempt to swithc the DN/DP wires of the SAM3
by Harald Welte
· 8 years ago
67415e3
HACK: Add EEPROM writing at boot of SAM3 on qmod
by Harald Welte
· 8 years ago
73d697d
i2c-bitbang: increase speed to ~110kHz
by Harald Welte
· 8 years ago
0aea9ff
Fix reading SDA in I2C bit-banging code
by Harald Welte
· 8 years ago
c6ae98c
i2c_bitbang: Change logic when to use i2c_delay()
by Harald Welte
· 8 years ago
226b40a
WIP: bit-banging I2C support for EEPROM access on QMOD
by Harald Welte
· 8 years ago
a02b641
Add support for 'qmod' (quad-modem) board
by Harald Welte
· 8 years ago
fd9c041
fix TRACE_ENTRY line termination (LF -> CRLF)
by Harald Welte
· 9 years ago
990f010
Add HardFault Exception Handler
by Harald Welte
· 9 years ago
e26c943
exceptions: Print name of exception to console
by Harald Welte
· 9 years ago
622b6be
Fix ADC based VCC detection
by Harald Welte
· 9 years ago
3bafe43
dynamically dispatch USART IRQs
by Harald Welte
· 9 years ago
dde112e
print instance/channel number in all trace messages
by Harald Welte
· 9 years ago
8ee15db
read SAM3S unique serial number at start and print it
by Harald Welte
· 9 years ago
28772eb
ADC: Make errata work-arounds depend on run-time detection of chip version
by Harald Welte
· 9 years ago
cf1c19a
src_simtrace/main: debug/trace logging improvements
by Harald Welte
· 9 years ago
04e37a8
firmware/main: Disable the rotor unless TRACE_DEBUG
by Harald Welte
· 9 years ago
5541e8a
USBD_HAL: Hard-code TRACE_LEVEL_WARNING
by Harald Welte
· 9 years ago
53079bb
debug/tracing updates
by Harald Welte
· 9 years ago
c58bba0
wait for UART Tx completion before switching baud rate at PTS
by Harald Welte
· 9 years ago
c8beefb
wait for transmitter to be done before receiving
by Harald Welte
· 9 years ago
903d63a
card_emu: Alwasys update state before enabling UART Rx/Tx
by Harald Welte
· 9 years ago
52d5546
card_emu: Avoid PTS related race-condition
by Harald Welte
· 9 years ago
ccb8a22
card_emu: Avoid PTS related race-condition
by Harald Welte
· 9 years ago
a929f21
card_emu: Differentiate between TRACE_{DEBUG/ERROR/INFO}
by Harald Welte
· 9 years ago
07872b6
VCC/ADC: finish implementing VCC detection via ADC
by Harald Welte
· 9 years ago
6dcacf3
OWHW: fix operation with second modem/UART
by Harald Welte
· 9 years ago
419eb8a
WIP: Use ADC to determine VCC voltage
by Harald Welte
· 9 years ago
ff16065
implement CEMU_USB_MSGT_DT_GET_STATUS
by Harald Welte
· 9 years ago
2315e6b
ensure git version ends up in firmware image
by Harald Welte
· 9 years ago
b26d003
split/segment multiple commands from single USB transfer
by Harald Welte
· 9 years ago
d295b92
ensure usb_msg_hdr contains raw message length
by Harald Welte
· 9 years ago
b8f9450
shrink ringbuffer size to 128 bytes
by Harald Welte
· 9 years ago
9f240b6
use irq-safe version of llist operations between USB callback and main
by Harald Welte
· 9 years ago
da15ca0
mode_cardemu: mask the USART status register with mask register
by Harald Welte
· 9 years ago
3d27c84
host_comm: Fix race condition in handling OUT USB transfers
by Harald Welte
· 9 years ago
250cd2c
host_communication: set rctx->tot_len after receiving USB transfer
by Harald Welte
· 9 years ago
372f4cc
board_lowlevel: Use LED definitions from board.h
by Harald Welte
· 9 years ago
5820ea9
dispatch_usb_command: Ensure list consistency + avoid mem leaks
by Harald Welte
· 9 years ago
0eaa992
cardem: Add support for USB host based set/clear of card_insert
by Harald Welte
· 9 years ago
7abdb51
ringbuffer: Make ring buffer access irq-save
by Harald Welte
· 9 years ago
7dd3dfd
convert all src_simtrace code to kernel coding style
by Harald Welte
· 9 years ago
1605564
ensure USB config numbers always start from 1
by Harald Welte
· 9 years ago
072dadd
main.c: Only call the configure() function of a configuration if it exists
by Harald Welte
· 9 years ago
40901a0
various printf/debug output improvements
by Harald Welte
· 9 years ago
57b3a25
Add Card-Emulation for second UART/USIM to USB descriptors
by Harald Welte
· 9 years ago
13e8202
mode_cardem: Prepare for full support of second UART/USIM
by Harald Welte
· 9 years ago
06b27f6
mode_cardemu: Implement CEMU_USB_MSGT_DT_SET_ATR
by Harald Welte
· 9 years ago
ebb80ed
introduce 'main' queue between USB receive and UART TX
by Harald Welte
· 9 years ago
ad43440
card_emu: Fix various compiler warnings by switch/default/break
by Harald Welte
· 9 years ago
5e00400
board_lowlevel.c: Improve main oscillator initialization
by Harald Welte
· 9 years ago
a0cf200
host_communication: keep track of number of pending/queued req_ctx
by Harald Welte
· 9 years ago
acd48c5
HACK: always use the USART interrupt handler of mode_cardemu()
by Harald Welte
· 9 years ago
fcdd660
card_emu: Don't de-reference a NULL variable
by Harald Welte
· 9 years ago
fde250a
uart_console.c: Don't redefine constants from board.h
by Harald Welte
· 9 years ago
715bc05
Increase serial console sped to 230400 bps
by Harald Welte
· 9 years ago
12d4bdf
mode_cardemu: Process RX interrupts before TX
by Harald Welte
· 9 years ago
dda7355
card_emu: Only transmit NULL byte from the right state
by Harald Welte
· 9 years ago
f1697e2
card_emu: Only allocate a new buffer if needed in send_tpdu_header()
by Harald Welte
· 9 years ago
acae412
explicitly inform card_emu once data to transmit has arrived
by Harald Welte
· 9 years ago
8a416b1
mode_cardemu: fix ordering of events when switching rx/tx mode
by Harald Welte
· 9 years ago
45688d4
mode_cardemu: Disable UART TXRDY generation if we don't have data to TX
by Harald Welte
· 9 years ago
349c54b
req_ctx: LF -> CR+LF
by Harald Welte
· 9 years ago
22925ea
test: Add TRACE_INFO and TRACE_ERROR definitions
by Harald Welte
· 9 years ago
4678388
board_lowlevel: More comments about clock initialization
by Harald Welte
· 9 years ago
ebbb645
req_ctx: Fix allocation (allocate 1 block, not all) and call _init()
by Harald Welte
· 9 years ago
54cb3d0
host_communication/card_emu: adapt to nwe req_ctx / queuing paradignm
by Harald Welte
· 9 years ago
f672e9d
req_ctx: Convert from hand-coded linked lists to linuxlist.h
by Harald Welte
· 9 years ago
b66ce24
req_ctx: Add better explanation about the various states
by Harald Welte
· 9 years ago
22bf67f
card_emu: Use \r\n instead of \n
by Harald Welte
· 9 years ago
708d85c
trace.h: Don't print file/function name in TRACE_DEBUG()
by Harald Welte
· 9 years ago
c0bd7f0
mode_cardemu: Move GPIO detection to IRQ, use ring buffer for UART RX
by Harald Welte
· 9 years ago
47ee283
card_emu_io_statechg(): properly determine edges from levels
by Harald Welte
· 9 years ago
99f62a6
mode_cardemu: update_fidi just needs to execute
by Harald Welte
· 9 years ago
2ad0ca1
host_communication: Fix TRACE_ERROR syntax
by Harald Welte
· 9 years ago
43f7949
card_emu: Add TRACE_DEBUG once TPDU header is sent to USB
by Harald Welte
· 9 years ago
b086ab0
owhw: Fix GPIO for USIM1_RST (24, not 23!) and enable SET_USIM1_PRES
by Harald Welte
· 9 years ago
9dbc46e
mode_cardemu: Proper enabling/disabling of USART IRQ sources
by Harald Welte
· 9 years ago
ba0c688
owhw: Make owhw/board.h the default for now
by Harald Welte
· 9 years ago
4dc3db7
req_ctx: Use only 10 small buffers, and no large ones
by Harald Welte
· 9 years ago
203ea19
req_ctx: Use the linked lists between req_ctx to ensure ordering
by Harald Welte
· 9 years ago
bd71768
mode_card_emu: connect the update_fidi() callback
by Harald Welte
· 9 years ago
2a6d3af
re-introduce req_ctx buffers into the host communication
by Harald Welte
· 9 years ago
29f8f0e
improvements in req_ctx debugging
by Harald Welte
· 9 years ago
2fb5996
owhw: fix GPIO definitions (output low level by default)
by Harald Welte
· 9 years ago
8c49636
card_emu.c: avoid re-defining update_fidi() symbol
by Harald Welte
· 9 years ago
390760a
add board/owhw.c
by Harald Welte
· 9 years ago
Next »