Gitiles
Code Review Sign In
gerrit.osmocom.org / simtrace2 / 7214b4747f904d07ccdd7977872b68957967eaf0 / firmware
  1. 7214b47 Make sure to print CPU Reset Cause when starting the software by Harald Welte · 8 years ago
  2. 45ebe45 Enable Watchdog (500ms) by Harald Welte · 8 years ago
  3. aaba4af Use Supply Controller to avoid running SAM3 on voltages lower than 3.0V by Harald Welte · 8 years ago
  4. 3ecbf67 only simtrace is bus-powered, SAM3 on qmod + owhw are self-powered by Harald Welte · 8 years ago
  5. 8adf0ac DFU app: call into board_main_top() for qmod related initialization by Harald Welte · 8 years ago
  6. f415d71 Call USBD_Disconnect before software-triggered CPU reset by Harald Welte · 8 years ago
  7. ec0837c change from \r\n (CRLF) to \n\r (LFCR) by Harald Welte · 8 years ago
  8. 0de99cd DFU: String descriptors for DFU alt-interfaces by Harald Welte · 8 years ago 0.2
  9. ac4f66e DFU: Set 10ms bwPollTimeout (lowest possible as per spec) by Harald Welte · 8 years ago
  10. 91fc402 DFU: make sure to properly initialize g_dfu pointer before using it by Harald Welte · 8 years ago
  11. b04f4f0 DFU Runtime: Add missing return after handling USB standard requests by Harald Welte · 8 years ago
  12. e8eea29 dfu: fix cosmetic issue in debug message by Harald Welte · 8 years ago
  13. d1e9634 DFU: fix transitions between runtime and DFU mode by Harald Welte · 8 years ago
  14. db17e83 cstartup: (re-)enable interrupts before calling main() by Harald Welte · 8 years ago
  15. ec9b5ff dfu/main.c: Initialize FLASHD driver before using it by Harald Welte · 8 years ago
  16. 0af4948 cstartup / USBD: Use correct Makefile conditionals for DFU by Harald Welte · 8 years ago
  17. adbe72a Makefile: Define APPLICATION_foo BOARD_bar and ENVIRONMENT_baz #defines by Harald Welte · 8 years ago
  18. e36970c dfu: print Chip ID during boot by Harald Welte · 8 years ago
  19. cab6641 flashd: Set 6 Wait states as per Errata requiremens for Revision A by Harald Welte · 8 years ago
  20. 479e97e DFU: Add missing 'return' after handling generic USB control request by Harald Welte · 8 years ago
  21. 203abf5 dfu_desc: Add some string descriptors and fix configuration desc table by Harald Welte · 8 years ago
  22. ee9ebb3 stdio: Increase max string size to 512 and don't endless-loop!! by Harald Welte · 8 years ago
  23. b2ad7f7 dfu_des.c: Cosmetic changes, use named initializers by Harald Welte · 8 years ago
  24. 0395bd1 move PLLB (for USB) initialization to board_lowlevel.c by Harald Welte · 8 years ago
  25. c430ac1 have local stdio.h file to avoid newlib issues by Harald Welte · 8 years ago
  26. adba0ce fix g_dfu access from both DFU and runtime access by Harald Welte · 8 years ago
  27. 65cca7c ensure g_dfu is linked to start of RAM when building DFU loader by Harald Welte · 8 years ago
  28. db30727 remove obsolete old linker script by Harald Welte · 8 years ago
  29. 32852bc DFU: towards a more complete implementation by Harald Welte · 8 years ago
  30. edf9c9d Makefile: Optimize for size by Harald Welte · 8 years ago
  31. 37b6e41 move last few files from src_board / include_board by Harald Welte · 8 years ago
  32. 964f509 remove pio_capture, we don't use it by Harald Welte · 8 years ago
  33. 96e62a4 stdio.c: fix compiler warning by Harald Welte · 8 years ago
  34. 045ea3e timer.h: Fix compiler warnings about redefinition by Harald Welte · 8 years ago
  35. d09829d Remove newlib dependency, include own stdio/string/assert by Harald Welte · 8 years ago
  36. d525231 fix some compiler warnings by Harald Welte · 8 years ago
  37. d8a003d Structure build system to build for multiple boards/apps/environments by Harald Welte · 8 years ago
  38. a1cd0f3 fix compilation of card_emu_tests by Harald Welte · 8 years ago
  39. 3f5e3dd Change directory structure to align with Atmel softpack by Harald Welte · 8 years ago
  40. 7ed6f3b WIP: Introduce USB DFU code from my at91lib DFU port by Harald Welte · 8 years ago
  41. aa3b867 WIP: split main from board-speciic parts by Harald Welte · 8 years ago
  42. a05ccc9 build efc.o and flashd.o as part of build process by Harald Welte · 8 years ago
  43. e9eaf90 import efc.[ch] and flashd.[ch] from SAM3S softpack 2.1 by Harald Welte · 8 years ago
  44. 1d91058 qmod: Inver initial state of PERST signals by Harald Welte · 8 years ago
  45. 4a9bce1 qmod: invert WWAN_PERST logic (we use transistors now) by Harald Welte · 8 years ago
  46. 6732248 Add support for board version reading via ADC by Harald Welte · 8 years ago
  47. 9c78cff Extend WWAN modem PERST to 300ms by Harald Welte · 8 years ago
  48. 987f59a Import libosmocore timer infrastructure and use it for PERST by Harald Welte · 8 years ago
  49. b41598b Introudce an include_libosmocore directory and move (updated) linuxlist there by Harald Welte · 8 years ago
  50. 7e5c7d5 Add debug commands '1' and '2' to generate 1ms reset pulses to modems by Harald Welte · 8 years ago
  51. 31f817c Add support for controlling PERST of WWAN modems (on qmod) by Harald Welte · 8 years ago
  52. 83207e0 Add 'mdelay()' function to busy-wait for given number of milli-seconds by Harald Welte · 8 years ago
  53. 2819e9c wwan_led: Read + report status changes of WWAN LED inputs by Harald Welte · 8 years ago
  54. af61479 qmod: Remove 'U' debug command and directly initialize USB by Harald Welte · 8 years ago
  55. fb3f308 board_lowlevel: Clean up PLLA configuration by Harald Welte · 8 years ago
  56. 84ad985 usb: Cofnigure PLLB according to board.h BOARD_MAINOSC by Harald Welte · 8 years ago
  57. 7861132 qmod: Don't violate PLL minimum output frequency by Harald Welte · 8 years ago
  58. b871363 qmod: cosmetic changes to EEPROM hex array by Harald Welte · 8 years ago
  59. b30783c qmod EEPROM: Dont't mark any ports as non-removable by Harald Welte · 8 years ago
  60. ae8a465 qmod: Commit missing changes to EEPROM by Harald Welte · 8 years ago
  61. 6dfcf70 qmod: Start with _HUB_RESET=0 -> HUB_RESET=1 (not in reset) by Harald Welte · 8 years ago
  62. f9a182d qmod: breal the command loop when 'U' is pressed and proceed to USB init by Harald Welte · 8 years ago
  63. afbb747 qmod: do not automatically clear _HUB_RESET after EEPROM write by Harald Welte · 8 years ago
  64. e07aed6 qmod: debug menu: Add 'U' command to proceed to USB by Harald Welte · 8 years ago
  65. 396354c qmod: debug menu: make sure to always print something by Harald Welte · 8 years ago
  66. 006b16d quad-modem: Add debug console commands for debugging by Harald Welte · 8 years ago
  67. e974fbb Issue ST12_PRTPWR_OVERRIDE before putting hub in reset by Harald Welte · 8 years ago
  68. 15e026e qmod: Set PIN_PRTPWR_OVERRIDE to output/low by Harald Welte · 8 years ago
  69. 4e3b9a5 qmod: attempt to swithc the DN/DP wires of the SAM3 by Harald Welte · 8 years ago
  70. 67415e3 HACK: Add EEPROM writing at boot of SAM3 on qmod by Harald Welte · 8 years ago
  71. 73d697d i2c-bitbang: increase speed to ~110kHz by Harald Welte · 8 years ago
  72. 0aea9ff Fix reading SDA in I2C bit-banging code by Harald Welte · 8 years ago
  73. c6ae98c i2c_bitbang: Change logic when to use i2c_delay() by Harald Welte · 8 years ago
  74. 226b40a WIP: bit-banging I2C support for EEPROM access on QMOD by Harald Welte · 8 years ago
  75. a02b641 Add support for 'qmod' (quad-modem) board by Harald Welte · 8 years ago
  76. fd9c041 fix TRACE_ENTRY line termination (LF -> CRLF) by Harald Welte · 9 years ago
  77. 990f010 Add HardFault Exception Handler by Harald Welte · 9 years ago
  78. e26c943 exceptions: Print name of exception to console by Harald Welte · 9 years ago
  79. 622b6be Fix ADC based VCC detection by Harald Welte · 9 years ago
  80. 3bafe43 dynamically dispatch USART IRQs by Harald Welte · 9 years ago
  81. dde112e print instance/channel number in all trace messages by Harald Welte · 9 years ago
  82. 8ee15db read SAM3S unique serial number at start and print it by Harald Welte · 9 years ago
  83. 28772eb ADC: Make errata work-arounds depend on run-time detection of chip version by Harald Welte · 9 years ago
  84. cf1c19a src_simtrace/main: debug/trace logging improvements by Harald Welte · 9 years ago
  85. 04e37a8 firmware/main: Disable the rotor unless TRACE_DEBUG by Harald Welte · 9 years ago
  86. 5541e8a USBD_HAL: Hard-code TRACE_LEVEL_WARNING by Harald Welte · 9 years ago
  87. 53079bb debug/tracing updates by Harald Welte · 9 years ago
  88. c58bba0 wait for UART Tx completion before switching baud rate at PTS by Harald Welte · 9 years ago
  89. c8beefb wait for transmitter to be done before receiving by Harald Welte · 9 years ago
  90. 903d63a card_emu: Alwasys update state before enabling UART Rx/Tx by Harald Welte · 9 years ago
  91. 52d5546 card_emu: Avoid PTS related race-condition by Harald Welte · 9 years ago
  92. ccb8a22 card_emu: Avoid PTS related race-condition by Harald Welte · 9 years ago
  93. a929f21 card_emu: Differentiate between TRACE_{DEBUG/ERROR/INFO} by Harald Welte · 9 years ago
  94. 07872b6 VCC/ADC: finish implementing VCC detection via ADC by Harald Welte · 9 years ago
  95. 6dcacf3 OWHW: fix operation with second modem/UART by Harald Welte · 9 years ago
  96. 419eb8a WIP: Use ADC to determine VCC voltage by Harald Welte · 9 years ago
  97. ff16065 implement CEMU_USB_MSGT_DT_GET_STATUS by Harald Welte · 9 years ago
  98. 2315e6b ensure git version ends up in firmware image by Harald Welte · 9 years ago
  99. b26d003 split/segment multiple commands from single USB transfer by Harald Welte · 9 years ago
  100. d295b92 ensure usb_msg_hdr contains raw message length by Harald Welte · 9 years ago