/* ----------------------------------------------------------------------------
 *         ATMEL Microcontroller Software Support
 * ----------------------------------------------------------------------------
 * Copyright (c) 2010, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */

/**
 *  \file
 *
 *  \section Purpose
 *
 *  This file provides a basic API for PIO configuration and usage of
 *  user-controlled pins. Please refer to the board.h file for a list of
 *  available pin definitions.
 *
 *  \section Usage
 *
 *  -# Define a constant pin description array such as the following one, using
 *     the existing definitions provided by the board.h file if possible:
 *     \code
 *        const Pin pPins[] = {PIN_USART0_TXD, PIN_USART0_RXD};
 *     \endcode
 *     Alternatively, it is possible to add new pins by provided the full Pin
 *     structure:
 *     \code
 *     // Pin instance to configure PA10 & PA11 as inputs with the internal
 *     // pull-up enabled.
 *     const Pin pPins = {
 *          (1 << 10) | (1 << 11),
 *          REG_PIOA,
 *          ID_PIOA,
 *          PIO_INPUT,
 *          PIO_PULLUP
 *     };
 *     \endcode
 *  -# Configure a pin array by calling PIO_Configure() with a pointer to the
 *     array and its size (which is computed using the PIO_LISTSIZE macro).
 *  -# Change and get the value of a user-controlled pin using the PIO_Set,
 *     PIO_Clear and PIO_Get methods.
 *  -# Get the level being currently output by a user-controlled pin configured
 *     as an output using PIO_GetOutputDataStatus().
 */

#ifndef _PIO_
#define _PIO_

/*
 *         Headers
 */

#include "chip.h"

#include <stdint.h>

/*
 *         Global Definitions
 */

/*  The pin is controlled by the associated signal of peripheral A. */
#define PIO_PERIPH_A                0
/*  The pin is controlled by the associated signal of peripheral B. */
#define PIO_PERIPH_B                1
/*  The pin is controlled by the associated signal of peripheral C. */
#define PIO_PERIPH_C                2
/*  The pin is controlled by the associated signal of peripheral D. */
#define PIO_PERIPH_D                3
/*  The pin is an input. */
#define PIO_INPUT                   4
/*  The pin is an output and has a default level of 0. */
#define PIO_OUTPUT_0                5
/*  The pin is an output and has a default level of 1. */
#define PIO_OUTPUT_1                6

/*  Default pin configuration (no attribute). */
#define PIO_DEFAULT                 (0 << 0)
/*  The internal pin pull-up is active. */
#define PIO_PULLUP                  (1 << 0)
/*  The internal glitch filter is active. */
#define PIO_DEGLITCH                (1 << 1)
/*  The pin is open-drain. */
#define PIO_OPENDRAIN               (1 << 2)

/*  The internal debouncing filter is active. */
#define PIO_DEBOUNCE                (1 << 3)

/*  Enable additional interrupt modes. */
#define PIO_IT_AIME                 (1 << 4)

/*  Interrupt High Level/Rising Edge detection is active. */
#define PIO_IT_RE_OR_HL             (1 << 5)
/*  Interrupt Edge detection is active. */
#define PIO_IT_EDGE                 (1 << 6)

/*  Low level interrupt is active */
#define PIO_IT_LOW_LEVEL            (0               | 0 | PIO_IT_AIME)
/*  High level interrupt is active */
#define PIO_IT_HIGH_LEVEL           (PIO_IT_RE_OR_HL | 0 | PIO_IT_AIME)
/*  Falling edge interrupt is active */
#define PIO_IT_FALL_EDGE            (0               | PIO_IT_EDGE | PIO_IT_AIME)
/*  Rising edge interrupt is active */
#define PIO_IT_RISE_EDGE            (PIO_IT_RE_OR_HL | PIO_IT_EDGE | PIO_IT_AIME)

#ifdef __cplusplus
 extern "C" {
#endif

/*
 *          Global Macros
 */

/**
 *  Calculates the size of an array of Pin instances. The array must be defined
 *  locally (i.e. not a pointer), otherwise the computation will not be correct.
 *  \param pPins  Local array of Pin instances.
 *  \return Number of elements in array.
 */
#define PIO_LISTSIZE(pPins)    (sizeof(pPins) / sizeof(Pin))

/*
 *         Global Types
 */


/*
 *  Describes the type and attribute of one PIO pin or a group of similar pins.
 *  The #type# field can have the following values:
 *     - PIO_PERIPH_A
 *     - PIO_PERIPH_B
 *     - PIO_OUTPUT_0
 *     - PIO_OUTPUT_1
 *     - PIO_INPUT
 *
 *  The #attribute# field is a bitmask that can either be set to PIO_DEFAULt,
 *  or combine (using bitwise OR '|') any number of the following constants:
 *     - PIO_PULLUP
 *     - PIO_DEGLITCH
 *     - PIO_DEBOUNCE
 *     - PIO_OPENDRAIN
 *     - PIO_IT_LOW_LEVEL
 *     - PIO_IT_HIGH_LEVEL
 *     - PIO_IT_FALL_EDGE
 *     - PIO_IT_RISE_EDGE
 */
typedef struct _Pin
{
    /*  Bitmask indicating which pin(s) to configure. */
    uint32_t mask;
    /*  Pointer to the PIO controller which has the pin(s). */
    Pio    *pio;
    /*  Peripheral ID of the PIO controller which has the pin(s). */
    uint8_t id;
    /*  Pin type. */
    uint8_t type;
    /*  Pin attribute. */
    uint8_t attribute;
} Pin ;

/*
 *         Global Access Macros
 */

/*
 *         Global Functions
 */

extern uint8_t PIO_Configure( const Pin *list, uint32_t size ) ;

extern void PIO_Set( const Pin *pin ) ;

extern void PIO_Clear( const Pin *pin ) ;

extern uint8_t PIO_Get( const Pin *pin ) ;

extern uint8_t PIO_GetOutputDataStatus( const Pin *pin ) ;

extern void PIO_SetDebounceFilter( const Pin *pin, uint32_t cuttoff );

#ifdef __cplusplus
}
#endif

#endif /* #ifndef _PIO_ */