diff --git a/doc/manuals/Makefile b/doc/manuals/Makefile
new file mode 100644
index 0000000..c9edcef
--- /dev/null
+++ b/doc/manuals/Makefile
@@ -0,0 +1,10 @@
+TOPDIR = ..
+
+ASCIIDOC = osmomsc-usermanual.adoc
+ASCIIDOC_DEPS = chapters/*.adoc
+include $(TOPDIR)/build/Makefile.asciidoc.inc
+
+VTY_REFERENCE = osmomsc-vty-reference.xml
+include $(TOPDIR)/build/Makefile.vty-reference.inc
+
+include $(TOPDIR)/build/Makefile.common.inc
diff --git a/doc/manuals/chapters/control.adoc b/doc/manuals/chapters/control.adoc
new file mode 100644
index 0000000..af03be7
--- /dev/null
+++ b/doc/manuals/chapters/control.adoc
@@ -0,0 +1,31 @@
+[[control]]
+== Control interface
+
+The actual protocol is described in <<common-control-if>>, the variables common
+to all programs using it are described in <<ctrl_common_vars>>. This section
+describes the CTRL interface variables specific to OsmoMSC.
+
+.Variables available on OsmoMSC's Control interface
+[options="header",width="100%",cols="20%,5%,5%,50%,20%"]
+|===
+|Name|Access|Trap|Value|Comment
+|subscriber-list-active-v1|RO|No||Return list of active subscribers.
+|===
+
+=== subscriber-list-active-v1
+
+Return a list of subscribers that are successfully attached (including full
+successful authentication and ciphering if those are enabled).
+
+The reply comprises of one subscriber per line, of the format
+
+----
+<IMSI>,<MSISDN>\n[<IMSI>,<MSISDN>\n[...]]
+----
+
+For example:
+
+----
+901700000015252,22801
+901700000015253,22802
+----
diff --git a/doc/manuals/chapters/counters.adoc b/doc/manuals/chapters/counters.adoc
new file mode 100644
index 0000000..7fbb10c
--- /dev/null
+++ b/doc/manuals/chapters/counters.adoc
@@ -0,0 +1,4 @@
+[[counters]]
+== Counters
+
+include::./counters_generated.adoc[]
diff --git a/doc/manuals/chapters/counters_generated.adoc b/doc/manuals/chapters/counters_generated.adoc
new file mode 100644
index 0000000..afeb8ff
--- /dev/null
+++ b/doc/manuals/chapters/counters_generated.adoc
@@ -0,0 +1,40 @@
+// autogenerated by show asciidoc counters
+These counters and their description based on OsmoMSC UNKNOWN (OsmoMSC).
+
+// generating tables for rate_ctr_group
+// rate_ctr_group table mobile switching center
+.msc - mobile switching center 
+[options="header"]
+|===
+| Name | Reference | Description
+| loc_update_type:attach | <<msc_loc_update_type:attach>> | Received location update imsi attach requests.
+| loc_update_type:normal | <<msc_loc_update_type:normal>> | Received location update normal requests.
+| loc_update_type:periodic | <<msc_loc_update_type:periodic>> | Received location update periodic requests.
+| loc_update_type:detach | <<msc_loc_update_type:detach>> | Received location update detach indication.
+| loc_update_resp:failed | <<msc_loc_update_resp:failed>> | Rejected location updates.
+| loc_update_resp:completed | <<msc_loc_update_resp:completed>> | Successful location updates.
+| sms:submitted | <<msc_sms:submitted>> | Received a RPDU from a MS (MO).
+| sms:no_receiver | <<msc_sms:no_receiver>> | Counts SMS which couldn't routed because no receiver found.
+| sms:delivered | <<msc_sms:delivered>> | Global SMS Deliver attempts.
+| sms:rp_err_mem | <<msc_sms:rp_err_mem>> | CAUSE_MT_MEM_EXCEEDED errors of MS responses on a sms deliver attempt.
+| sms:rp_err_other | <<msc_sms:rp_err_other>> | Other error of MS responses on a sms delive attempt.
+| sms:deliver_unknown_error | <<msc_sms:deliver_unknown_error>> | Unknown error occured during sms delivery.
+| call:mo_setup | <<msc_call:mo_setup>> | Received setup requests from a MS to init a MO call.
+| call:mo_connect_ack | <<msc_call:mo_connect_ack>> | Received a connect ack from MS of a MO call. Call is now succesful connected up.
+| call:mt_setup | <<msc_call:mt_setup>> | Sent setup requests to the MS (MT).
+| call:mt_connect | <<msc_call:mt_connect>> | Sent a connect to the MS (MT).
+| call:active | <<msc_call:active>> | Count total amount of calls that ever reached active state.
+| call:complete | <<msc_call:complete>> | Count total amount of calls which got terminated by disconnect req or ind after reaching active state.
+| call:incomplete | <<msc_call:incomplete>> | Count total amount of call which got terminated by any other reason after reaching active state.
+|===
+// generating tables for osmo_stat_items
+// generating tables for osmo_counters
+// ungrouped osmo_counters
+.ungrouped osmo counters
+[options="header"]
+|===
+| Name | Reference | Description
+| msc.active_calls | <<ungroup_counter_msc.active_calls>> | 
+|===
+
+
diff --git a/doc/manuals/chapters/net.adoc b/doc/manuals/chapters/net.adoc
new file mode 100644
index 0000000..06be4ba
--- /dev/null
+++ b/doc/manuals/chapters/net.adoc
@@ -0,0 +1,154 @@
+[[net]]
+== Configuring the Core Network
+
+The core network parameters are configured by the config file (as in `osmo-msc
+-c osmo-msc.cfg`). The config file is parsed by the VTY, which is also
+available via telnet in the running `osmo-msc` instance. Be aware that even
+though you may be able to change these parameters without restarting
+`osmo-msc`, some may not take immediate effect, and it is safest to use the
+config file to have these parameters set at startup time.
+
+The core network parameters are found in the `config` / `network`.
+
+A full reference to the available commands can be found in the _OsmoMSC VTY
+reference manual_ <<vty-ref-osmomsc>>. This section describes only the most
+commonly used settings.
+
+Here is an overview of the config items, described in more detail below:
+
+----
+network
+ network country code 262
+ mobile network code 89
+ mm info 1
+ short name OsmoMSC
+ long name OsmoMSC
+ authentication required
+ encryption a5 3
+----
+
+[TIP]
+====
+Use the telnet VTY interface to query the current configuration of a running
+`osmo-msc` process:
+
+----
+$ telnet localhost 4254
+OsmoMSC> enable
+OsmoMSC# show running-config
+----
+
+Some parameters may be changed without restarting `osmo-msc`. To reach the
+`network` node, enter:
+
+----
+OsmoMSC> enable
+OsmoMSC# configure terminal
+OsmoMSC(config)# network
+OsmoMSC(config-net)# short name Example-Name
+OsmoMSC(config-net)# exit
+OsmoMSC(config)#
+----
+
+The telnet VTY features tab-completion as well as context sensitive help shown
+when entering a `?` question mark.
+
+You can always use the `list` VTY command or enter `?` on the blank prompt to
+get a list of all possible commands at the current node.
+====
+
+
+=== MCC/MNC
+
+The key identities of every GSM PLMN is the Mobile Country Code and the Mobile
+Network Code. They are identical over the entire network. In most cases, the
+MCC/MNC will be allocated to the operator by the respective local regulatory
+authority. For example, to set the MCC/MNC of 262-89, have this in your
+osmo-msc.cfg:
+
+----
+network
+ network country code 262
+ mobile network code 89
+----
+
+
+=== Configuring MM INFO
+
+The _MM INFO_ procedure can be used after a successful _LOCATION UPDATE_ in
+order to transmit the human-readable network name as well as local time zone
+information to the MS.  By default, _MM INFO_ is not active, i.e. `0`. Set to `1`
+to activate this feature:
+
+----
+network
+ mm info 1
+ short name OsmoMSC
+ long name OsmoMSC
+----
+
+[NOTE]
+====
+Not all phones support the MM INFO procedure. If a phone is not
+factory-programmed to contain the name for your MCC/MNC, it will likely only
+provide a numeric display of the network name, such as _262-89_, or show the
+country code transformed into a letter, such as _D 89_.
+====
+
+The time information transmitted is determined by the local system time of the
+operating system on which OsmoMSC is running.
+
+
+=== Authentication
+
+Authorized subscribers must be entered in the HLR database, see the _OsmoHLR
+reference manual_ <<userman-osmohlr>>. If authentication tokens (such as KI for
+2G, or K and OP/OPC for UMTS) are present in the HLR, OsmoMSC will only attach
+a subscriber after successful authentication.
+
+If no authentication keys are present in the HLR for a given subscriber,
+OsmoMSC will attach the subscriber _without_ authentication. You can reject
+subscribers that lack authentication info in the HLR with this setting:
+
+----
+network
+ authentication required
+----
+
+=== Ciphering
+
+To enable ciphering on the radio link, authentication must take place first:
+the Kc resulting from authentication is the key used for ciphering. Hence, all
+subscribers must have authentication tokens available in the HLR for ciphering.
+
+The MS, BTS and MSC must agree on a ciphering algorithm to use.
+
+- The MS sends its supported ciphering algorithms via Classmark IEs during
+  Location Updating.
+- Typically the BSC needs to know which A5 ciphers are supported by connected
+  BTSes.
+- Finally, OsmoMSC may impose that specific A5 ciphers shall not be considered.
+
+It is the responsibility of the BSC to then pick an A5 cipher that satisfies
+all requirements.
+
+- In OsmoMSC, A5/0 means that ciphering is turned off.
++
+----
+network
+ encryption a5 0
+----
+
+- A5/1 and A5/3 are currently supported by Osmocom.
++
+----
+network
+ encryption a5 3
+----
+
+- Never use A5/2: it is an "export grade cipher" and has been deprecated for
+  its low ciphering strength.
+
+NOTE: At the time of writing, OsmoMSC supports setting only a single A5 cipher,
+while it should be able to allow a set of ciphers. This is subject to ongoing
+development.
diff --git a/doc/manuals/chapters/overview.adoc b/doc/manuals/chapters/overview.adoc
new file mode 100644
index 0000000..0bb47d7
--- /dev/null
+++ b/doc/manuals/chapters/overview.adoc
@@ -0,0 +1,127 @@
+[[overview]]
+== Overview
+
+This manual should help you getting started with OsmoMSC. It will cover
+aspects of configuring and running the OsmoMSC.
+
+[[intro_overview]]
+=== About OsmoMSC
+
+OsmoMSC is the Osmocom implementation of a Mobile Switching Center (MSC) for 2G
+and 3G GSM and UMTS mobile networks. Its interfaces are:
+
+- GSUP towards OsmoHLR (or a MAP proxy);
+- A over IP towards a BSC (e.g. OsmoBSC);
+- IuCS towards an RNC or HNB-GW (e.g. OsmoHNBGW) for 3G voice;
+- MNCC (Mobile Network Call Control derived from GSM TS 04.07);
+- SMPP 3.4 (Short Message Peer-to-Peer);
+- The Osmocom typical telnet VTY and CTRL interfaces.
+
+OsmoMSC originated from the OpenBSC project, which started as a minimalistic
+all-in-one implementation of the GSM Network. In 2017, OpenBSC had reached
+maturity and diversity (including M3UA SIGTRAN and 3G support in the form of
+IuCS and IuPS interfaces) that naturally lead to a separation of the all-in-one
+approach to fully independent separate programs as in typical GSM networks.
+Before it was split off, OsmoMSC originated from libmsc of the old openbsc.git.
+Since a true _A_ interface and IuCS for 3G support is available, OsmoMSC
+exists only as a separate standalone entity.
+
+Key differences of the new OsmoMSC compared to the old OsmoNITB are:
+
+- The complete VLR implementation that communicates with the separate HLR
+  (OsmoHLR) for subscriber management. In contrast to the OsmoNITB, HLR queries
+  are fully asynchronous, and the separate HLR allows using centralized
+  subscriber management for both circuit-switched and packet-switched domains
+  (i.e. one OsmoHLR for both OsmoMSC and OsmoSGSN).
+
+- VLR and HLR brought full UMTS AKA (Authentication and Key Agreement) support,
+  i.e. Milenage authentication in both the full 3G variant as well as the
+  backwards compatible 2G variant.
+
+- Addition of a true _A_ interface for 2G voice services. Previously, OsmoBSC
+  had an SCCPlite based _A_ interface towards 3rd party MSC implementations.
+  OsmoMSC features a true SCCP/M3UA _A_ interface, which allows running OsmoBSC
+  against this Osmocom based MSC implementation. The new SCCP/M3UA SIGTRAN for
+  the _A_ interface is implemented in libosmo-sccp, which is used by OsmoMSC
+  and OsmoBSC (and others), to establish a link via an STP (e.g. OsmoSTP).
+
+- Addition of an _IuCS_ interface to allow operating 3G voice services, also
+  via SCCP/M3UA SIGTRAN, for example connecting via OsmoHNBGW to a 3G small
+  cell device.
+
+Find the OsmoMSC issue tracker and wiki online at
+
+- https://osmocom.org/projects/osmomsc
+- https://osmocom.org/projects/osmomsc/wiki
+
+
+[[fig-gsm]]
+.Typical GSM network architecture used with OsmoMSC
+[graphviz]
+----
+digraph G {
+	rankdir=LR;
+	MS0 [label="MS"]
+	MS1 [label="MS"]
+	MS2 [label="MS"]
+	MS3 [label="MS"]
+	UE0 [label="UE"]
+	UE1 [label="UE"]
+	BTS0 [label="BTS"]
+	BTS1 [label="BTS"]
+	STP [label="STP\n(SCCP routing)"]
+	HLR [label="HLR+AUC+EIR"]
+	HNB [label="RNC or hNodeB"]
+	MGW
+	MS0->BTS0 [label="Um"]
+	MS1->BTS0 [label="Um"]
+	MS2->BTS1 [label="Um"]
+	MS3->BTS1 [label="Um"]
+	UE0->HNB
+	UE1->HNB
+	BTS0->BSC [label="Abis"]
+	BTS1->BSC [label="Abis"]
+	BSC->STP [label="A/SCCP/M3UA"]
+	STP->MSC [label="A/SCCP/M3UA"]
+	STP->MSC [label="IuCS/SCCP/M3UA"]
+	VLR->HLR [label="GSUP"]
+	HNB->HNBGW [label="Iuh"]
+	HNBGW->STP [label="IuCS/SCCP/M3UA"]
+	MSC->MGW [label="MGCP"]
+	BTS0->MGW [label="RTP"]
+	BTS1->MGW [label="RTP"]
+	subgraph cluster_msc {
+		label = "OsmoMSC";
+		MSC->SMSC;
+		MSC->VLR
+	}
+}
+----
+
+
+=== Software Components
+
+This is a brief description of OsmoMSC's internal software components.
+
+==== SMSC
+
+A minimal store-and-forward server for SMS, supporting both MO and MT
+SMS service, as well as multi-part messages.
+
+The built-in SMSC also supports an external SMSC interface.  For more
+information, see <<smpp>>.
+
+==== MSC
+
+The MSC component implements the mobility management (MM) functions of the TS
+04.08 and delegates to SMSC for SMS message handling and the VLR for subscriber
+management.
+
+Furthermore, it can handle TS 04.08 Call Control (CC), either by use of
+an internal MNCC handler, or by use of an external MNCC agent.  For more
+information see <<mncc>>.
+
+==== VLR
+
+A fully featured Visitor Location Register handles the subscriber management
+and authentication, and interfaces via GSUP to the external HLR.
diff --git a/doc/manuals/chapters/running.adoc b/doc/manuals/chapters/running.adoc
new file mode 100644
index 0000000..cb68157
--- /dev/null
+++ b/doc/manuals/chapters/running.adoc
@@ -0,0 +1,148 @@
+== Running OsmoMSC
+
+The OsmoMSC executable (`osmo-msc`) offers the following command-line
+arguments:
+
+=== SYNOPSIS
+
+*osmo-msc* [-h|-V] [-d 'DBGMASK'] [-D] [-c 'CONFIGFILE'] [-s] [-T] [-e 'LOGLEVEL'] [-l 'DATABASE'] [-M 'SOCKETPATH'] [-C]
+
+=== OPTIONS
+
+*-h, --help*::
+	Print a short help message about the supported options
+*-V, --version*::
+	Print the compile-time version number of the OsmoBTS program
+*-d, --debug 'DBGMASK','DBGLEVELS'*::
+	Set the log subsystems and levels for logging to stderr. This
+	has mostly been superseded by VTY-based logging configuration,
+	see <<logging>> for further information.
+*-D, --daemonize*::
+	Fork the process as a daemon into background.
+*-c, --config-file 'CONFIGFILE'*::
+	Specify the file and path name of the configuration file to be
+	used. If none is specified, use `osmo-msc.cfg` in the current
+	working directory.
+*-s, --disable-color*::
+	Disable colors for logging to stderr. This has mostly been
+	deprecated by VTY based logging configuration, see <<logging>>
+	for more information.
+*-T, --timestamp*::
+	Enable time-stamping of log messages to stderr. This has mostly
+	been deprecated by VTY based logging configuration, see
+	<<logging>> for more information.
+*-e, --log-level 'LOGLEVEL'*::
+	Set the global log level for logging to stderr. This has mostly
+	been deprecated by VTY based logging configuration, see
+	<<logging>> for more information.
+*-l, --database 'DATABASE'*::
+	Specify the file name of the SQLite3 database to use as SMS storage
+*-M, --mncc-sock-path*::
+	Enable the MNCC socket for an external MNCC handler. See
+	<<mncc>> for further information.
+*-m, --mncc-sock*::
+	Same as option -M (deprecated).
+*-C, --no-dbcounter*::
+	Disable the regular periodic synchronization of statistics
+	counters to the database.
+
+
+=== Multiple instances
+
+Running multiple instances of `osmo-msc` on the same computer is possible if all
+interfaces (VTY, CTRL) are separated using the appropriate configuration
+options. The IP based interfaces are binding to local host by default. In order
+to separate the processes, the user has to bind those services to specific but
+different IP addresses and/or ports.
+
+The VTY and the Control interface can be bound to IP addresses from the loopback
+address range, for example:
+
+----
+line vty
+ bind 127.0.0.2
+ctrl
+ bind 127.0.0.2
+----
+
+If external SMPP is enabled, you may bind it to a different interface using:
+
+----
+smpp
+ local-tcp-ip 10.23.42.1 2775
+----
+
+More on SMPP configuration in <<smpp-config-global>>.
+
+The external MNCC handler is configured by the `--mncc-sock` commandline
+argument. Choose a different such socket path for each OsmoMSC instance running
+on the same file system. See more in <<mncc-external>>.
+
+For the following links, OsmoMSC acts as a client and does not listen/bind to a
+specific interface, and will hence not encounter conflicts for multiple instances
+running on the same interface:
+
+- The SCCP/M3UA links are established by OsmoMSC contacting an STP.
+- The GSUP link is established by OsmoMSC contacting an HLR.
+
+
+=== Configure primary links
+
+==== Configure SCCP/M3UA to accept _A_ and _IuCS_ links
+
+OsmoMSC will contact an STP instance to establish an SCCP/M3UA link. BSC and
+HNBGW will then reach the MSC via this link. By default, an STP instance is
+assumed to listen on the default M3UA port (2905) on the local host.
+
+Establishing an SCCP/M3UA link towards an STP instance not on the local host
+can be configured as follows:
+
+----
+cs7 instance 0
+ asp my-OsmoMSC 2905 0 m3ua
+  ! IP address of the remote STP:
+  remote-ip 10.23.24.1
+----
+
+Note that _A_ and _IuCS_ may use different SCCP instances, if so desired:
+
+----
+cs7 instance 0
+ asp my-OsmoMSC-A 2905 0 m3ua
+  remote-ip 10.23.42.1
+cs7 instance 1
+ asp my-OsmoMSC-Iu 2905 0 m3ua
+  remote-ip 10.23.42.2
+msc
+ cs7-instance-a 0
+ cs7-instance-iu 1
+----
+
+A full configuration needs an `asp` on an `as` -- an Application Server Process
+running on an Application Server -- as well as a local point code and routing
+configuration. The SCCP VTY automatically creates those parts that are missing,
+by assuming sane defaults. A complete configuration would look like this:
+
+----
+cs7 instance 0
+ point-code 0.23.1
+ asp my-OsmoMSC-A-Iu 2905 0 m3ua
+  remote-ip 127.0.0.1
+ as my-as-for-OsmoMSC-A-Iu m3ua
+  asp my-OsmoMSC-A-Iu
+  routing-key 0 0.23.1
+----
+
+==== Configure GSUP to reach the HLR
+
+OsmoMSC will assume a GSUP server (OsmoHLR) to run on the local host and the
+default GSUP port (4222). Contacting an HLR at a different IP address can be
+configured as follows:
+
+----
+hlr
+ ! IP address of the remote HLR:
+ remote-ip 10.23.42.1
+ ! default port is 4222, optionally configurable by:
+ remote-port 1234
+----
diff --git a/doc/manuals/images/sgs-imsi_attach_lu.msc b/doc/manuals/images/sgs-imsi_attach_lu.msc
new file mode 100644
index 0000000..e62c2b8
--- /dev/null
+++ b/doc/manuals/images/sgs-imsi_attach_lu.msc
@@ -0,0 +1,15 @@
+msc {
+	UE, MME, VLR [label="MSC/VLR"], HSS [label="HSS/HLR"];
+
+	UE => MME [label="Attach Request"];
+	UE box HSS [label="Steps 3..16 of LTE Attach procedure TS 23.401"];
+	MME box MME [label="Derive VLR Number"];
+	MME => VLR [label="LU Request"];
+	VLR box VLR [label="Create SGs Association"];
+	VLR box HSS [label="MAP/GSUP UL / ISD"];
+	MME <= VLR [label="LU Accept"];
+	UE box HSS [label="Steps 17..16 of LTE Attach procedure TS 23.401"];
+	|||;
+	...;
+	MME <= VLR [label="Paging Request"];
+}
diff --git a/doc/manuals/images/sgs-mo_call_no_ps_ho.msc b/doc/manuals/images/sgs-mo_call_no_ps_ho.msc
new file mode 100644
index 0000000..f886c89
--- /dev/null
+++ b/doc/manuals/images/sgs-mo_call_no_ps_ho.msc
@@ -0,0 +1,18 @@
+msc {
+	hscale=2;
+	UE, ENB [label="eNodeB"], BSS, MME, VLR [label="MSC/VLR"], HSS [label="HSS/HLR"];
+
+	UE => MME	[label="NAS Extended Service Request"];
+	ENB <= MME	[label="S1-AP UE Context Mod Req with CSFB"];
+	ENB => MME	[label="S1-AP UE Context Mod Resp"];
+	UE <= ENB	[label="NACC (Network Assisted Cell Change)"];
+	ENB => MME	[label="S1-AP S1 UE Context Release Req"];
+	UE box MME	[label="S1 UE Context Release"];
+
+	UE box HSS	[label="UE changes RAT then LA and/or RA update"];
+	UE <=> HSS	[label="PS Suspend (TS 23.060)"];
+
+	UE => BSS	[label="CM SERV REQ"];
+	BSS => VLR	[label="COMPL L3 (CM SERV REQ)"];
+	UE <=> VLR	[label="Normal 2G Voice Call"];
+}
diff --git a/doc/manuals/images/sgs-mo_sms_idle.msc b/doc/manuals/images/sgs-mo_sms_idle.msc
new file mode 100644
index 0000000..5acc0e8
--- /dev/null
+++ b/doc/manuals/images/sgs-mo_sms_idle.msc
@@ -0,0 +1,21 @@
+msc {
+	hscale=2;
+	UE, MME, VLR [label="MSC/VLR"], HSS [label="HSS/HLR"], SMSC;
+
+	UE box HSS	[label="EPS/IMSI attach procedure"];
+	...;
+	UE box MME	[label="UE triggered Service Request"];
+	UE => MME	[label="UL NAS Transport"];
+	MME => VLR	[label="SGsAP UPLINK UNITDATA\n(CP-DATA/RP-DATA/TPDU)"];
+	VLR => SMSC	[label="MAP/GSUP Forward SM"];
+	MME <= VLR	[label="SGsAP DOWNLINK UNITDATA"];
+	UE <= MME	[label="DL NAS Transport"];
+	...;
+
+	VLR <= SMSC	[label="Delivery Report"];
+	MME <= VLR	[label="SGsAP DOWNLINK UNITDATA"];
+	UE <= MME	[label="DL NAS Transport"];
+	UE => MME	[label="UL NAS Transport"];
+	MME => VLR	[label="SGsAP UPLINK UNITDATA"];
+	MME <= VLR	[label="SGsAP RELEASE REQ"];
+}
diff --git a/doc/manuals/images/sgs-mt_call_idle.msc b/doc/manuals/images/sgs-mt_call_idle.msc
new file mode 100644
index 0000000..b3cff3c
--- /dev/null
+++ b/doc/manuals/images/sgs-mt_call_idle.msc
@@ -0,0 +1,17 @@
+msc {
+	hscale=2;
+	UE, ENB [label="eNodeB"], BSS, MME, VLR [label="MSC/VLR"], PSTN;
+
+	VLR <= PSTN	[label="ISUP IAM or SIP INVITE"];
+	MME <= VLR	[label="SGsAP PAGING REQUEST"];
+	ENB <= MME	[label="Paging"];
+	UE <= MME	[label="Paging"];
+
+	UE => MME	[label="Extended Service Req"];
+	MME => VLR	[label="SGsAP SERVICE REQUEST"];
+	ENB <= MME	[label="Initial UE Ctx Setup"];
+
+	UE => BSS	[label="Paging Response"];
+	BSS => VLR	[label="COMPL L3 (PAGING RESP)"];
+	UE <=> VLR	[label="Normal 2G Voice Call"];
+}
diff --git a/doc/manuals/images/sgs-mt_sms_idle.msc b/doc/manuals/images/sgs-mt_sms_idle.msc
new file mode 100644
index 0000000..7b453e0
--- /dev/null
+++ b/doc/manuals/images/sgs-mt_sms_idle.msc
@@ -0,0 +1,22 @@
+msc {
+	hscale=2;
+	UE, MME, VLR [label="MSC/VLR"], HSS [label="HSS/HLR"], SMSC;
+
+	UE box HSS	[label="EPS/IMSI attach procedure"];
+	...;
+
+	VLR <= SMSC	[label="MAP/GSUP ForwardSM"];
+	MME <= VLR	[label="SGsAP PAGING"];
+	UE <= MME	[label="Paging"];
+	UE box MME	[label="Service Request"];
+	MME => VLR	[label="SGsAP SERVICE REQ"];
+	MME <= VLR	[label="SGsAP DL UNITDATA\n(CP-DATA/RP-DATA/TPDU)"];
+	UE <= MME	[label="DL NAS Transport"];
+	UE => MME	[label="UL NAS Transport"];
+	MME => VLR	[label="SGsAP UL UNITDATA"];
+	...;
+	UE => MME	[label="UL NAS Transport"];
+	MME => VLR	[label="SGsAP UL UNITDATA"];
+	VLR => SMSC	[label="Delivery report"];
+	MME <= VLR	[label="SGsAP RELEASE REQ"];
+}
diff --git a/doc/manuals/osmomsc-usermanual-docinfo.xml b/doc/manuals/osmomsc-usermanual-docinfo.xml
new file mode 100644
index 0000000..d99bba7
--- /dev/null
+++ b/doc/manuals/osmomsc-usermanual-docinfo.xml
@@ -0,0 +1,47 @@
+<revhistory>
+  <revision>
+    <revnumber>1</revnumber>
+    <date>September 18th, 2017</date>
+    <authorinitials>NH</authorinitials>
+    <revremark>
+      Initial version; based on OsmoNITB manual version 2.
+    </revremark>
+  </revision>
+</revhistory>
+
+<authorgroup>
+  <author>
+    <firstname>Neels</firstname>
+    <surname>Hofmeyr</surname>
+    <email>nhofmeyr@sysmocom.de</email>
+    <authorinitials>NH</authorinitials>
+    <affiliation>
+      <shortaffil>sysmocom</shortaffil>
+      <orgname>sysmocom - s.f.m.c. GmbH</orgname>
+      <jobtitle>Senior Developer</jobtitle>
+    </affiliation>
+  </author>
+</authorgroup>
+
+<copyright>
+  <year>2017</year>
+  <holder>sysmocom - s.f.m.c. GmbH</holder>
+</copyright>
+
+<legalnotice>
+  <para>
+	Permission is granted to copy, distribute and/or modify this
+	document under the terms of the GNU Free Documentation License,
+	Version 1.3 or any later version published by the Free Software
+	Foundation; with the Invariant Sections being just 'Foreword',
+	'Acknowledgements' and 'Preface', with no Front-Cover Texts,
+	and no Back-Cover Texts.  A copy of the license is included in
+	the section entitled "GNU Free Documentation License".
+  </para>
+  <para>
+	The Asciidoc source code of this manual can be found at
+	<ulink url="http://git.osmocom.org/osmo-gsm-manuals/">
+		http://git.osmocom.org/osmo-gsm-manuals/
+	</ulink>
+  </para>
+</legalnotice>
diff --git a/doc/manuals/osmomsc-usermanual.adoc b/doc/manuals/osmomsc-usermanual.adoc
new file mode 100644
index 0000000..ac68d93
--- /dev/null
+++ b/doc/manuals/osmomsc-usermanual.adoc
@@ -0,0 +1,40 @@
+:gfdl-enabled:
+:program-name: OsmoMSC
+
+OsmoMSC User Manual
+====================
+Neels Hofmeyr <nhofmeyr@sysmocom.de>
+
+
+include::../common/chapters/preface.adoc[]
+
+include::chapters/overview.adoc[]
+
+include::chapters/running.adoc[]
+
+include::chapters/control.adoc[]
+
+include::chapters/counters.adoc[]
+
+include::../common/chapters/vty.adoc[]
+
+include::../common/chapters/logging.adoc[]
+
+include::chapters/net.adoc[]
+
+include::../common/chapters/smpp.adoc[]
+
+include::../common/chapters/mncc.adoc[]
+
+include::../common/chapters/control_if.adoc[]
+
+include::../common/chapters/gsup.adoc[]
+
+include::../common/chapters/port_numbers.adoc[]
+
+include::../common/chapters/bibliography.adoc[]
+
+include::../common/chapters/glossary.adoc[]
+
+include::../common/chapters/gfdl.adoc[]
+
diff --git a/doc/manuals/osmomsc-vty-reference.xml b/doc/manuals/osmomsc-vty-reference.xml
new file mode 100644
index 0000000..3b54e9e
--- /dev/null
+++ b/doc/manuals/osmomsc-vty-reference.xml
@@ -0,0 +1,38 @@
+<?xml version="1.0" encoding="UTF-8"?>
+<!--
+  ex:ts=2:sw=42sts=2:et
+  -*- tab-width: 4; c-basic-offset: 4; indent-tabs-mode: nil -*-
+-->
+<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML 5.0//EN"
+"http://docbook.org/xml/5.0/dtd/docbook.dtd" [
+<!ENTITY chapter-vty      SYSTEM      "../common/chapters/vty.xml" >
+<!ENTITY sections-vty     SYSTEM      "generated/docbook_vty.xml"  >
+]>
+
+<book>
+  <info>
+    <revhistory>
+        <revision>
+            <revnumber>v1</revnumber>
+            <date>18th September 2017</date>
+            <authorinitials>nh</authorinitials>
+            <revremark>Initial</revremark>
+        </revision>
+    </revhistory>
+
+    <title>OsmoMSC VTY Reference</title>
+
+    <copyright>
+      <year>2017</year>
+    </copyright>
+
+    <legalnotice>
+      <para>This work is copyright by <orgname>sysmocom - s.f.m.c. GmbH</orgname>. All rights reserved.
+      </para>
+    </legalnotice>
+  </info>
+
+  <!-- Main chapters-->
+  &chapter-vty;
+</book>
+
diff --git a/doc/manuals/vty/msc_vty_additions.xml b/doc/manuals/vty/msc_vty_additions.xml
new file mode 100644
index 0000000..adc0f7e
--- /dev/null
+++ b/doc/manuals/vty/msc_vty_additions.xml
@@ -0,0 +1,21 @@
+<vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'>
+    <node id='config-mncc-int'>
+      <name>MNCC Internal Configuration</name>
+      <description>This node allows to configure the default codecs for
+      the internal call control handling.</description>
+    </node>
+    <node id='config-smpp'>
+      <name>SMPP Configuration</name>
+      <description>This node allows to configure the SMPP interface
+	for interfacing with external SMS applications. This section
+	contains generic/common SMPP related configuration, and no
+	per-ESME specific parameters.</description>
+    </node>
+    <node id='config-smpp-esme'>
+      <name>ESME Configuration</name>
+      <description>This node allows to configure one particular SMPP
+      ESME, which is an External SMS Entity such as a SMS based
+      application server.  You can define any number of ESME within
+      the SMPP node of the OsmoNITB VTY.</description>
+    </node>
+</vtydoc>
diff --git a/doc/manuals/vty/msc_vty_reference.xml b/doc/manuals/vty/msc_vty_reference.xml
new file mode 100644
index 0000000..bb7e958
--- /dev/null
+++ b/doc/manuals/vty/msc_vty_reference.xml
@@ -0,0 +1,2686 @@
+<vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'>
+  <node id='_common_cmds_'>
+    <name>Common Commands</name>
+    <description>These commands are available on all VTY nodes. They are listed here only once, to unclutter the VTY reference.</description>
+    <command id='help'>
+      <params>
+        <param name='help' doc='Description of the interactive help system' />
+      </params>
+    </command>
+    <command id='list'>
+      <params>
+        <param name='list' doc='Print command list' />
+      </params>
+    </command>
+    <command id='write terminal'>
+      <params>
+        <param name='write' doc='Write running configuration to memory, network, or terminal' />
+        <param name='terminal' doc='Write to terminal' />
+      </params>
+    </command>
+    <command id='write file'>
+      <params>
+        <param name='write' doc='Write running configuration to memory, network, or terminal' />
+        <param name='file' doc='Write to configuration file' />
+      </params>
+    </command>
+    <command id='write memory'>
+      <params>
+        <param name='write' doc='Write running configuration to memory, network, or terminal' />
+        <param name='memory' doc='Write configuration to the file (same as write file)' />
+      </params>
+    </command>
+    <command id='write'>
+      <params>
+        <param name='write' doc='Write running configuration to memory, network, or terminal' />
+      </params>
+    </command>
+    <command id='show running-config'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='running-config' doc='running configuration' />
+      </params>
+    </command>
+    <command id='exit'>
+      <params>
+        <param name='exit' doc='Exit current mode and down to previous mode' />
+      </params>
+    </command>
+    <command id='end'>
+      <params>
+        <param name='end' doc='End current mode and change to enable mode.' />
+      </params>
+    </command>
+  </node>
+  <node id='view'>
+    <name>view</name>
+    <command id='show version'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='version' doc='Displays program version' />
+      </params>
+    </command>
+    <command id='show online-help'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='online-help' doc='Online help' />
+      </params>
+    </command>
+    <command id='enable'>
+      <params>
+        <param name='enable' doc='Turn on privileged mode command' />
+      </params>
+    </command>
+    <command id='terminal length &lt;0-512&gt;'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='length' doc='Set number of lines on a screen' />
+        <param name='&lt;0-512&gt;' doc='Number of lines on screen (0 for no pausing)' />
+      </params>
+    </command>
+    <command id='terminal no length'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='length' doc='Set number of lines on a screen' />
+      </params>
+    </command>
+    <command id='who'>
+      <params>
+        <param name='who' doc='Display who is on vty' />
+      </params>
+    </command>
+    <command id='show history'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='history' doc='Display the session command history' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; users'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='users' doc='User Table' />
+      </params>
+    </command>
+    <command id='show cs7 (sua|m3ua|ipa) [&lt;0-65534&gt;]'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='sua' doc='SCCP User Adaptation' />
+        <param name='m3ua' doc='MTP3 User Adaptation' />
+        <param name='ipa' doc='IPA Multiplex (SCCP Lite)' />
+        <param name='[&lt;0-65534&gt;]' doc='Port Number' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; asp'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='asp' doc='Application Server Process (ASP)' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; as (active|all|m3ua|sua)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='as' doc='Application Server (AS)' />
+        <param name='active' doc='Display all active ASs' />
+        <param name='all' doc='Display all ASs (default)' />
+        <param name='m3ua' doc='Display all m3ua ASs' />
+        <param name='sua' doc='Display all SUA ASs' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp addressbook'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='addressbook' doc='List all SCCP addressbook entries' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp users'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='users' doc='Show List of SCCP Users registered' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp ssn &lt;0-65535&gt;'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='ssn' doc='Find an SCCP User registered for the given SSN' />
+        <param name='&lt;0-65535&gt;' doc='Subsystem Number (SSN)' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp connections'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='connections' doc='Show List of active SCCP connections' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp timers'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signaling Connection Control Part' />
+        <param name='timers' doc='Show List of SCCP timers' />
+      </params>
+    </command>
+    <command id='logging enable'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='enable' doc='Enables logging to this vty' />
+      </params>
+    </command>
+    <command id='logging disable'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='disable' doc='Disables logging to this vty' />
+      </params>
+    </command>
+    <command id='logging filter all (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='all' doc='Do you want to log all messages?' />
+        <param name='0' doc='Only print messages matched by other filters' />
+        <param name='1' doc='Bypass filter and print all messages' />
+      </params>
+    </command>
+    <command id='logging color (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='color' doc='Configure color-printing for log messages' />
+        <param name='0' doc='Don&apos;t use color for printing messages' />
+        <param name='1' doc='Use color for printing messages' />
+      </params>
+    </command>
+    <command id='logging timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp' />
+      </params>
+    </command>
+    <command id='logging print extended-timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='extended-timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
+      </params>
+    </command>
+    <command id='logging print category (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem name' />
+      </params>
+    </command>
+    <command id='logging print category-hex (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category-hex' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem nr in hex (&apos;&lt;000b&gt;&apos;)' />
+      </params>
+    </command>
+    <command id='logging print level (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='level' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the log level name' />
+      </params>
+    </command>
+    <command id='logging print file (0|1|basename) [last]'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='file' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the source file and line' />
+        <param name='basename' doc='Prefix each log message with the source file&apos;s basename (strip leading paths) and line' />
+        <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' />
+      </params>
+    </command>
+    <command id='logging set-log-mask MASK'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='set-log-mask' doc='Set the logmask of this logging target' />
+        <param name='MASK' doc='List of logging categories to log, e.g. &apos;abc:mno:xyz&apos;. Available log categories depend on the specific application, refer to the &apos;logging level&apos; command. Optionally add individual log levels like &apos;abc,1:mno,3:xyz,5&apos;, where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' />
+      </params>
+    </command>
+    <command id='logging level (rll|cc|mm|rr|mncc|pag|msc|mgcp|ho|db|ref|ctrl|smpp|ranap|vlr|iucs|bssap|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf) (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='rll' doc='A-bis Radio Link Layer (RLL)' />
+        <param name='cc' doc='Layer3 Call Control (CC)' />
+        <param name='mm' doc='Layer3 Mobility Management (MM)' />
+        <param name='rr' doc='Layer3 Radio Resource (RR)' />
+        <param name='mncc' doc='MNCC API for Call Control application' />
+        <param name='pag' doc='Paging Subsystem' />
+        <param name='msc' doc='Mobile Switching Center' />
+        <param name='mgcp' doc='Media Gateway Control Protocol' />
+        <param name='ho' doc='Hand-Over' />
+        <param name='db' doc='Database Layer' />
+        <param name='ref' doc='Reference Counting' />
+        <param name='ctrl' doc='Control interface' />
+        <param name='smpp' doc='SMPP interface for external SMS apps' />
+        <param name='ranap' doc='Radio Access Network Application Part Protocol' />
+        <param name='vlr' doc='Visitor Location Register' />
+        <param name='iucs' doc='Iu-CS Protocol' />
+        <param name='bssap' doc='BSSAP Protocol (A Interface)' />
+        <param name='lglobal' doc='Library-internal global log family' />
+        <param name='llapd' doc='LAPD in libosmogsm' />
+        <param name='linp' doc='A-bis Intput Subsystem' />
+        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+        <param name='lmi' doc='A-bis Input Driver for Signalling' />
+        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+        <param name='lctrl' doc='Control Interface' />
+        <param name='lgtp' doc='GPRS GTP library' />
+        <param name='lstats' doc='Statistics messages and logging' />
+        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+        <param name='loap' doc='Osmocom Authentication Protocol' />
+        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+        <param name='ljibuf' doc='libosmo-netif Jitter Buffer' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level set-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level force-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the &apos;no logging level force-all&apos; command. Note: any &apos;logging level &lt;category&gt; &lt;level&gt;&apos; commands will have no visible effect after this, until the forced level is released.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='no logging level force-all'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Release any globally forced log level set with &apos;logging level force-all &lt;level&gt;&apos;' />
+      </params>
+    </command>
+    <command id='show logging vty'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='logging' doc='Show current logging configuration' />
+        <param name='vty' doc='Show current logging configuration for this vty' />
+      </params>
+    </command>
+    <command id='show alarms'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='alarms' doc='Show current logging configuration' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH) tree ADDRESS'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+        <param name='tree' doc='Display only a specific memory chunk' />
+        <param name='ADDRESS' doc='Chunk address (e.g. 0xdeadbeef)' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH) filter REGEXP'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+        <param name='filter' doc='Filter chunks using regular expression' />
+        <param name='REGEXP' doc='Regular expression' />
+      </params>
+    </command>
+    <command id='show stats'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='stats' doc='Show statistical values' />
+      </params>
+    </command>
+    <command id='show stats level (global|peer|subscriber)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='stats' doc='Show statistical values' />
+        <param name='level' doc='Set the maximum group level' />
+        <param name='global' doc='Show global groups only' />
+        <param name='peer' doc='Show global and network peer related groups' />
+        <param name='subscriber' doc='Show global, peer, and subscriber groups' />
+      </params>
+    </command>
+    <command id='show asciidoc counters'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='asciidoc' doc='Asciidoc generation' />
+        <param name='counters' doc='Generate table of all registered counters' />
+      </params>
+    </command>
+    <command id='show rate-counters'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='rate-counters' doc='Show all rate counters' />
+      </params>
+    </command>
+    <command id='show fsm NAME'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='fsm' doc='Show information about finite state machines' />
+        <param name='NAME' doc='Display information about a single named finite state machine' />
+      </params>
+    </command>
+    <command id='show fsm all'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='fsm' doc='Show information about finite state machines' />
+        <param name='all' doc='Display a list of all registered finite state machines' />
+      </params>
+    </command>
+    <command id='show fsm-instances NAME'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='fsm-instances' doc='Show information about finite state machine instances' />
+        <param name='NAME' doc='Display a list of all FSM instances of the named finite state machine' />
+      </params>
+    </command>
+    <command id='show fsm-instances all'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='fsm-instances' doc='Show information about finite state machine instances' />
+        <param name='all' doc='Display a list of all FSM instances of all finite state machine' />
+      </params>
+    </command>
+    <command id='show subscriber (msisdn|extension|imsi|tmsi|id) ID'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+      </params>
+    </command>
+    <command id='show subscriber cache'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='subscriber' doc='Show information about subscribers' />
+        <param name='cache' doc='Display contents of subscriber cache' />
+      </params>
+    </command>
+    <command id='show connection'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='connection' doc='Subscriber Connections' />
+      </params>
+    </command>
+    <command id='show transaction'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='transaction' doc='Transactions' />
+      </params>
+    </command>
+    <command id='sms send pending'>
+      <params>
+        <param name='sms' doc='SMS related commands' />
+        <param name='send' doc='SMS Sending related commands' />
+        <param name='pending' doc='Send all pending SMS' />
+      </params>
+    </command>
+    <command id='sms delete expired'>
+      <params>
+        <param name='sms' doc='SMS related commands' />
+        <param name='delete' doc='SMS Database related commands' />
+        <param name='expired' doc='Delete all expired SMS' />
+      </params>
+    </command>
+    <command id='subscriber create imsi ID'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='create' doc='Create new subscriber' />
+        <param name='imsi' doc='Identify the subscriber by his IMSI' />
+        <param name='ID' doc='Identifier for the subscriber' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID sms sender (msisdn|extension|imsi|tmsi|id) SENDER_ID send .LINE'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='sms' doc='SMS Operations' />
+        <param name='sender' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='SENDER_ID' doc='Identifier for the subscriber' />
+        <param name='send' doc='Send SMS' />
+        <param name='.LINE' doc='Actual SMS Text' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID silent-sms sender (msisdn|extension|imsi|tmsi|id) SENDER_ID send .LINE'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='silent-sms' doc='Silent SMS Operations' />
+        <param name='sender' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='SENDER_ID' doc='Identifier for the subscriber' />
+        <param name='send' doc='Send SMS' />
+        <param name='.LINE' doc='Actual SMS Text' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID silent-call start (any|tch/f|tch/any|sdcch)'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='silent-call' doc='Silent call operation' />
+        <param name='start' doc='Start silent call' />
+        <param name='any' doc='Any channel' />
+        <param name='tch/f' doc='TCH/F channel' />
+        <param name='tch/any' doc='Any TCH channel' />
+        <param name='sdcch' doc='SDCCH channel' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID silent-call stop'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='silent-call' doc='Silent call operation' />
+        <param name='stop' doc='Stop silent call' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID ussd-notify (0|1|2) .TEXT'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='ussd-notify' doc='Send a USSD notify to the subscriber' />
+        <param name='0' doc='Alerting Level 0' />
+        <param name='1' doc='Alerting Level 1' />
+        <param name='2' doc='Alerting Level 2' />
+        <param name='.TEXT' doc='Text of USSD message to send' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID ms-test close-loop (a|b|c|d|e|f|i)'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='ms-test' doc='Send a TS 04.14 MS Test Command to subscriber' />
+        <param name='close-loop' doc='Close a TCH Loop inside the MS' />
+        <param name='a' doc='Loop Type A' />
+        <param name='b' doc='Loop Type B' />
+        <param name='c' doc='Loop Type C' />
+        <param name='d' doc='Loop Type D' />
+        <param name='e' doc='Loop Type E' />
+        <param name='f' doc='Loop Type F' />
+        <param name='i' doc='Loop Type I' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID ms-test open-loop'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='ms-test' doc='Send a TS 04.14 MS Test Command to subscriber' />
+        <param name='open-loop' doc='Open a TCH Loop inside the MS' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID paging'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='paging' doc='Issue an empty Paging for the subscriber (for debugging)' />
+      </params>
+    </command>
+    <command id='show statistics'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='statistics' doc='Display network statistics' />
+      </params>
+    </command>
+    <command id='show sms-queue'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='sms-queue' doc='Display SMSqueue statistics' />
+      </params>
+    </command>
+    <command id='logging filter imsi IMSI'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='imsi' doc='Filter log messages by IMSI' />
+        <param name='IMSI' doc='IMSI to be used as filter' />
+      </params>
+    </command>
+    <command id='show smpp esme'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='smpp' doc='SMPP Interface' />
+        <param name='esme' doc='SMPP Extrenal SMS Entity' />
+      </params>
+    </command>
+  </node>
+  <node id='enable'>
+    <name>enable</name>
+    <command id='disable'>
+      <params>
+        <param name='disable' doc='Turn off privileged mode command' />
+      </params>
+    </command>
+    <command id='configure terminal'>
+      <params>
+        <param name='configure' doc='Configuration from vty interface' />
+        <param name='terminal' doc='Configuration terminal' />
+      </params>
+    </command>
+    <command id='copy running-config startup-config'>
+      <params>
+        <param name='copy' doc='Copy configuration' />
+        <param name='running-config' doc='Copy running config to... ' />
+        <param name='startup-config' doc='Copy running config to startup config (same as write file)' />
+      </params>
+    </command>
+    <command id='show startup-config'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='startup-config' doc='Contentes of startup configuration' />
+      </params>
+    </command>
+    <command id='show version'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='version' doc='Displays program version' />
+      </params>
+    </command>
+    <command id='show online-help'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='online-help' doc='Online help' />
+      </params>
+    </command>
+    <command id='terminal length &lt;0-512&gt;'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='length' doc='Set number of lines on a screen' />
+        <param name='&lt;0-512&gt;' doc='Number of lines on screen (0 for no pausing)' />
+      </params>
+    </command>
+    <command id='terminal no length'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='length' doc='Set number of lines on a screen' />
+      </params>
+    </command>
+    <command id='who'>
+      <params>
+        <param name='who' doc='Display who is on vty' />
+      </params>
+    </command>
+    <command id='show history'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='history' doc='Display the session command history' />
+      </params>
+    </command>
+    <command id='terminal monitor'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='monitor' doc='Copy debug output to the current terminal line' />
+      </params>
+    </command>
+    <command id='terminal no monitor'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='monitor' doc='Copy debug output to the current terminal line' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; users'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='users' doc='User Table' />
+      </params>
+    </command>
+    <command id='show cs7 (sua|m3ua|ipa) [&lt;0-65534&gt;]'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='sua' doc='SCCP User Adaptation' />
+        <param name='m3ua' doc='MTP3 User Adaptation' />
+        <param name='ipa' doc='IPA Multiplex (SCCP Lite)' />
+        <param name='[&lt;0-65534&gt;]' doc='Port Number' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; asp'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='asp' doc='Application Server Process (ASP)' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; as (active|all|m3ua|sua)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='as' doc='Application Server (AS)' />
+        <param name='active' doc='Display all active ASs' />
+        <param name='all' doc='Display all ASs (default)' />
+        <param name='m3ua' doc='Display all m3ua ASs' />
+        <param name='sua' doc='Display all SUA ASs' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp addressbook'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='addressbook' doc='List all SCCP addressbook entries' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp users'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='users' doc='Show List of SCCP Users registered' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp ssn &lt;0-65535&gt;'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='ssn' doc='Find an SCCP User registered for the given SSN' />
+        <param name='&lt;0-65535&gt;' doc='Subsystem Number (SSN)' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp connections'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='connections' doc='Show List of active SCCP connections' />
+      </params>
+    </command>
+    <command id='show cs7 instance &lt;0-15&gt; sccp timers'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='An instance of the SS7 stack' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+        <param name='sccp' doc='Signaling Connection Control Part' />
+        <param name='timers' doc='Show List of SCCP timers' />
+      </params>
+    </command>
+    <command id='logging enable'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='enable' doc='Enables logging to this vty' />
+      </params>
+    </command>
+    <command id='logging disable'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='disable' doc='Disables logging to this vty' />
+      </params>
+    </command>
+    <command id='logging filter all (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='all' doc='Do you want to log all messages?' />
+        <param name='0' doc='Only print messages matched by other filters' />
+        <param name='1' doc='Bypass filter and print all messages' />
+      </params>
+    </command>
+    <command id='logging color (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='color' doc='Configure color-printing for log messages' />
+        <param name='0' doc='Don&apos;t use color for printing messages' />
+        <param name='1' doc='Use color for printing messages' />
+      </params>
+    </command>
+    <command id='logging timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp' />
+      </params>
+    </command>
+    <command id='logging print extended-timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='extended-timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
+      </params>
+    </command>
+    <command id='logging print category (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem name' />
+      </params>
+    </command>
+    <command id='logging print category-hex (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category-hex' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem nr in hex (&apos;&lt;000b&gt;&apos;)' />
+      </params>
+    </command>
+    <command id='logging print level (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='level' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the log level name' />
+      </params>
+    </command>
+    <command id='logging print file (0|1|basename) [last]'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='file' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the source file and line' />
+        <param name='basename' doc='Prefix each log message with the source file&apos;s basename (strip leading paths) and line' />
+        <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' />
+      </params>
+    </command>
+    <command id='logging set-log-mask MASK'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='set-log-mask' doc='Set the logmask of this logging target' />
+        <param name='MASK' doc='List of logging categories to log, e.g. &apos;abc:mno:xyz&apos;. Available log categories depend on the specific application, refer to the &apos;logging level&apos; command. Optionally add individual log levels like &apos;abc,1:mno,3:xyz,5&apos;, where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' />
+      </params>
+    </command>
+    <command id='logging level (rll|cc|mm|rr|mncc|pag|msc|mgcp|ho|db|ref|ctrl|smpp|ranap|vlr|iucs|bssap|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf) (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='rll' doc='A-bis Radio Link Layer (RLL)' />
+        <param name='cc' doc='Layer3 Call Control (CC)' />
+        <param name='mm' doc='Layer3 Mobility Management (MM)' />
+        <param name='rr' doc='Layer3 Radio Resource (RR)' />
+        <param name='mncc' doc='MNCC API for Call Control application' />
+        <param name='pag' doc='Paging Subsystem' />
+        <param name='msc' doc='Mobile Switching Center' />
+        <param name='mgcp' doc='Media Gateway Control Protocol' />
+        <param name='ho' doc='Hand-Over' />
+        <param name='db' doc='Database Layer' />
+        <param name='ref' doc='Reference Counting' />
+        <param name='ctrl' doc='Control interface' />
+        <param name='smpp' doc='SMPP interface for external SMS apps' />
+        <param name='ranap' doc='Radio Access Network Application Part Protocol' />
+        <param name='vlr' doc='Visitor Location Register' />
+        <param name='iucs' doc='Iu-CS Protocol' />
+        <param name='bssap' doc='BSSAP Protocol (A Interface)' />
+        <param name='lglobal' doc='Library-internal global log family' />
+        <param name='llapd' doc='LAPD in libosmogsm' />
+        <param name='linp' doc='A-bis Intput Subsystem' />
+        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+        <param name='lmi' doc='A-bis Input Driver for Signalling' />
+        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+        <param name='lctrl' doc='Control Interface' />
+        <param name='lgtp' doc='GPRS GTP library' />
+        <param name='lstats' doc='Statistics messages and logging' />
+        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+        <param name='loap' doc='Osmocom Authentication Protocol' />
+        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+        <param name='ljibuf' doc='libosmo-netif Jitter Buffer' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level set-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level force-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the &apos;no logging level force-all&apos; command. Note: any &apos;logging level &lt;category&gt; &lt;level&gt;&apos; commands will have no visible effect after this, until the forced level is released.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='no logging level force-all'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Release any globally forced log level set with &apos;logging level force-all &lt;level&gt;&apos;' />
+      </params>
+    </command>
+    <command id='show logging vty'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='logging' doc='Show current logging configuration' />
+        <param name='vty' doc='Show current logging configuration for this vty' />
+      </params>
+    </command>
+    <command id='show alarms'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='alarms' doc='Show current logging configuration' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH) tree ADDRESS'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+        <param name='tree' doc='Display only a specific memory chunk' />
+        <param name='ADDRESS' doc='Chunk address (e.g. 0xdeadbeef)' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH) filter REGEXP'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+        <param name='filter' doc='Filter chunks using regular expression' />
+        <param name='REGEXP' doc='Regular expression' />
+      </params>
+    </command>
+    <command id='show stats'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='stats' doc='Show statistical values' />
+      </params>
+    </command>
+    <command id='show stats level (global|peer|subscriber)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='stats' doc='Show statistical values' />
+        <param name='level' doc='Set the maximum group level' />
+        <param name='global' doc='Show global groups only' />
+        <param name='peer' doc='Show global and network peer related groups' />
+        <param name='subscriber' doc='Show global, peer, and subscriber groups' />
+      </params>
+    </command>
+    <command id='show asciidoc counters'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='asciidoc' doc='Asciidoc generation' />
+        <param name='counters' doc='Generate table of all registered counters' />
+      </params>
+    </command>
+    <command id='show rate-counters'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='rate-counters' doc='Show all rate counters' />
+      </params>
+    </command>
+    <command id='show fsm NAME'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='fsm' doc='Show information about finite state machines' />
+        <param name='NAME' doc='Display information about a single named finite state machine' />
+      </params>
+    </command>
+    <command id='show fsm all'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='fsm' doc='Show information about finite state machines' />
+        <param name='all' doc='Display a list of all registered finite state machines' />
+      </params>
+    </command>
+    <command id='show fsm-instances NAME'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='fsm-instances' doc='Show information about finite state machine instances' />
+        <param name='NAME' doc='Display a list of all FSM instances of the named finite state machine' />
+      </params>
+    </command>
+    <command id='show fsm-instances all'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='fsm-instances' doc='Show information about finite state machine instances' />
+        <param name='all' doc='Display a list of all FSM instances of all finite state machine' />
+      </params>
+    </command>
+    <command id='show subscriber (msisdn|extension|imsi|tmsi|id) ID'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+      </params>
+    </command>
+    <command id='show subscriber cache'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='subscriber' doc='Show information about subscribers' />
+        <param name='cache' doc='Display contents of subscriber cache' />
+      </params>
+    </command>
+    <command id='show connection'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='connection' doc='Subscriber Connections' />
+      </params>
+    </command>
+    <command id='show transaction'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='transaction' doc='Transactions' />
+      </params>
+    </command>
+    <command id='sms send pending'>
+      <params>
+        <param name='sms' doc='SMS related commands' />
+        <param name='send' doc='SMS Sending related commands' />
+        <param name='pending' doc='Send all pending SMS' />
+      </params>
+    </command>
+    <command id='sms delete expired'>
+      <params>
+        <param name='sms' doc='SMS related commands' />
+        <param name='delete' doc='SMS Database related commands' />
+        <param name='expired' doc='Delete all expired SMS' />
+      </params>
+    </command>
+    <command id='subscriber create imsi ID'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='create' doc='Create new subscriber' />
+        <param name='imsi' doc='Identify the subscriber by his IMSI' />
+        <param name='ID' doc='Identifier for the subscriber' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID sms sender (msisdn|extension|imsi|tmsi|id) SENDER_ID send .LINE'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='sms' doc='SMS Operations' />
+        <param name='sender' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='SENDER_ID' doc='Identifier for the subscriber' />
+        <param name='send' doc='Send SMS' />
+        <param name='.LINE' doc='Actual SMS Text' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID silent-sms sender (msisdn|extension|imsi|tmsi|id) SENDER_ID send .LINE'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='silent-sms' doc='Silent SMS Operations' />
+        <param name='sender' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='SENDER_ID' doc='Identifier for the subscriber' />
+        <param name='send' doc='Send SMS' />
+        <param name='.LINE' doc='Actual SMS Text' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID silent-call start (any|tch/f|tch/any|sdcch)'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='silent-call' doc='Silent call operation' />
+        <param name='start' doc='Start silent call' />
+        <param name='any' doc='Any channel' />
+        <param name='tch/f' doc='TCH/F channel' />
+        <param name='tch/any' doc='Any TCH channel' />
+        <param name='sdcch' doc='SDCCH channel' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID silent-call stop'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='silent-call' doc='Silent call operation' />
+        <param name='stop' doc='Stop silent call' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID ussd-notify (0|1|2) .TEXT'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='ussd-notify' doc='Send a USSD notify to the subscriber' />
+        <param name='0' doc='Alerting Level 0' />
+        <param name='1' doc='Alerting Level 1' />
+        <param name='2' doc='Alerting Level 2' />
+        <param name='.TEXT' doc='Text of USSD message to send' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID ms-test close-loop (a|b|c|d|e|f|i)'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='ms-test' doc='Send a TS 04.14 MS Test Command to subscriber' />
+        <param name='close-loop' doc='Close a TCH Loop inside the MS' />
+        <param name='a' doc='Loop Type A' />
+        <param name='b' doc='Loop Type B' />
+        <param name='c' doc='Loop Type C' />
+        <param name='d' doc='Loop Type D' />
+        <param name='e' doc='Loop Type E' />
+        <param name='f' doc='Loop Type F' />
+        <param name='i' doc='Loop Type I' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID ms-test open-loop'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='ms-test' doc='Send a TS 04.14 MS Test Command to subscriber' />
+        <param name='open-loop' doc='Open a TCH Loop inside the MS' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID paging'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='paging' doc='Issue an empty Paging for the subscriber (for debugging)' />
+      </params>
+    </command>
+    <command id='show statistics'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='statistics' doc='Display network statistics' />
+      </params>
+    </command>
+    <command id='show sms-queue'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='sms-queue' doc='Display SMSqueue statistics' />
+      </params>
+    </command>
+    <command id='logging filter imsi IMSI'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='imsi' doc='Filter log messages by IMSI' />
+        <param name='IMSI' doc='IMSI to be used as filter' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID expire'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='expire' doc='Expire the subscriber Now' />
+      </params>
+    </command>
+    <command id='sms-queue trigger'>
+      <params>
+        <param name='sms-queue' doc='SMS Queue' />
+        <param name='trigger' doc='Trigger sending messages' />
+      </params>
+    </command>
+    <command id='sms-queue max-pending &lt;1-500&gt;'>
+      <params>
+        <param name='sms-queue' doc='SMS Queue' />
+        <param name='max-pending' doc='SMS to deliver in parallel' />
+        <param name='&lt;1-500&gt;' doc='Amount' />
+      </params>
+    </command>
+    <command id='sms-queue clear'>
+      <params>
+        <param name='sms-queue' doc='SMS Queue' />
+        <param name='clear' doc='Clear the queue of pending SMS' />
+      </params>
+    </command>
+    <command id='sms-queue max-failure &lt;1-500&gt;'>
+      <params>
+        <param name='sms-queue' doc='SMS Queue' />
+        <param name='max-failure' doc='Maximum amount of delivery failures' />
+        <param name='&lt;1-500&gt;' doc='Amount' />
+      </params>
+    </command>
+    <command id='subscriber (msisdn|extension|imsi|tmsi|id) ID sms pending-send'>
+      <params>
+        <param name='subscriber' doc='Operations on a Subscriber' />
+        <param name='msisdn' doc='Identify subscriber by MSISDN (phone number)' />
+        <param name='extension' doc='Legacy alias for &apos;msisdn&apos;' />
+        <param name='imsi' doc='Identify subscriber by IMSI' />
+        <param name='tmsi' doc='Identify subscriber by TMSI' />
+        <param name='id' doc='Identify subscriber by database ID' />
+        <param name='ID' doc='Identifier for the subscriber' />
+        <param name='sms' doc='SMS Operations' />
+        <param name='pending-send' doc='Send pending SMS' />
+      </params>
+    </command>
+    <command id='show smpp esme'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='smpp' doc='SMPP Interface' />
+        <param name='esme' doc='SMPP Extrenal SMS Entity' />
+      </params>
+    </command>
+  </node>
+  <node id='config'>
+    <name>config</name>
+    <command id='hostname WORD'>
+      <params>
+        <param name='hostname' doc='Set system&apos;s network name' />
+        <param name='WORD' doc='This system&apos;s network name' />
+      </params>
+    </command>
+    <command id='no hostname [HOSTNAME]'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='hostname' doc='Reset system&apos;s network name' />
+        <param name='[HOSTNAME]' doc='Host name of this router' />
+      </params>
+    </command>
+    <command id='password (8|) WORD'>
+      <params>
+        <param name='password' doc='Assign the terminal connection password' />
+        <param name='8' doc='Specifies a HIDDEN password will follow' />
+        <param name='' doc='dummy string ' />
+        <param name='WORD' doc='The HIDDEN line password string' />
+      </params>
+    </command>
+    <command id='password LINE'>
+      <params>
+        <param name='password' doc='Assign the terminal connection password' />
+        <param name='LINE' doc='The UNENCRYPTED (cleartext) line password' />
+      </params>
+    </command>
+    <command id='enable password (8|) WORD'>
+      <params>
+        <param name='enable' doc='Modify enable password parameters' />
+        <param name='password' doc='Assign the privileged level password' />
+        <param name='8' doc='Specifies a HIDDEN password will follow' />
+        <param name='' doc='dummy string ' />
+        <param name='WORD' doc='The HIDDEN &apos;enable&apos; password string' />
+      </params>
+    </command>
+    <command id='enable password LINE'>
+      <params>
+        <param name='enable' doc='Modify enable password parameters' />
+        <param name='password' doc='Assign the privileged level password' />
+        <param name='LINE' doc='The UNENCRYPTED (cleartext) &apos;enable&apos; password' />
+      </params>
+    </command>
+    <command id='no enable password'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='enable' doc='Modify enable password parameters' />
+        <param name='password' doc='Assign the privileged level password' />
+      </params>
+    </command>
+    <command id='banner motd default'>
+      <params>
+        <param name='banner' doc='Set banner string' />
+        <param name='motd' doc='Strings for motd' />
+        <param name='default' doc='Default string' />
+      </params>
+    </command>
+    <command id='banner motd file [FILE]'>
+      <params>
+        <param name='banner' doc='Set banner' />
+        <param name='motd' doc='Banner for motd' />
+        <param name='file' doc='Banner from a file' />
+        <param name='[FILE]' doc='Filename' />
+      </params>
+    </command>
+    <command id='no banner motd'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='banner' doc='Set banner string' />
+        <param name='motd' doc='Strings for motd' />
+      </params>
+    </command>
+    <command id='service terminal-length &lt;0-512&gt;'>
+      <params>
+        <param name='service' doc='Set up miscellaneous service' />
+        <param name='terminal-length' doc='System wide terminal length configuration' />
+        <param name='&lt;0-512&gt;' doc='Number of lines of VTY (0 means no line control)' />
+      </params>
+    </command>
+    <command id='no service terminal-length [&lt;0-512&gt;]'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='service' doc='Set up miscellaneous service' />
+        <param name='terminal-length' doc='System wide terminal length configuration' />
+        <param name='[&lt;0-512&gt;]' doc='Number of lines of VTY (0 means no line control)' />
+      </params>
+    </command>
+    <command id='line vty'>
+      <params>
+        <param name='line' doc='Configure a terminal line' />
+        <param name='vty' doc='Virtual terminal' />
+      </params>
+    </command>
+    <command id='service advanced-vty'>
+      <params>
+        <param name='service' doc='Set up miscellaneous service' />
+        <param name='advanced-vty' doc='Enable advanced mode vty interface' />
+      </params>
+    </command>
+    <command id='no service advanced-vty'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='service' doc='Set up miscellaneous service' />
+        <param name='advanced-vty' doc='Enable advanced mode vty interface' />
+      </params>
+    </command>
+    <command id='show history'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='history' doc='Display the session command history' />
+      </params>
+    </command>
+    <command id='cs7 instance &lt;0-15&gt;'>
+      <params>
+        <param name='cs7' doc='ITU-T Signaling System 7' />
+        <param name='instance' doc='Configure a SS7 Instance' />
+        <param name='&lt;0-15&gt;' doc='An instance of the SS7 stack' />
+      </params>
+    </command>
+    <command id='ctrl'>
+      <params>
+        <param name='ctrl' doc='Configure the Control Interface' />
+      </params>
+    </command>
+    <command id='log stderr'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='stderr' doc='Logging via STDERR of the process' />
+      </params>
+    </command>
+    <command id='no log stderr'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='stderr' doc='Logging via STDERR of the process' />
+      </params>
+    </command>
+    <command id='log file .FILENAME'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='file' doc='Logging to text file' />
+        <param name='.FILENAME' doc='Filename' />
+      </params>
+    </command>
+    <command id='no log file .FILENAME'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='file' doc='Logging to text file' />
+        <param name='.FILENAME' doc='Filename' />
+      </params>
+    </command>
+    <command id='log alarms &lt;2-32700&gt;'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='alarms' doc='Logging alarms to osmo_strrb' />
+        <param name='&lt;2-32700&gt;' doc='Maximum number of messages to log' />
+      </params>
+    </command>
+    <command id='no log alarms'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='alarms' doc='Logging alarms to osmo_strrb' />
+      </params>
+    </command>
+    <command id='log syslog (authpriv|cron|daemon|ftp|lpr|mail|news|user|uucp)'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='syslog' doc='Logging via syslog' />
+        <param name='authpriv' doc='Security/authorization messages facility' />
+        <param name='cron' doc='Clock daemon (cron/at) facility' />
+        <param name='daemon' doc='General system daemon facility' />
+        <param name='ftp' doc='Ftp daemon facility' />
+        <param name='lpr' doc='Line printer facility' />
+        <param name='mail' doc='Mail facility' />
+        <param name='news' doc='News facility' />
+        <param name='user' doc='Generic facility' />
+        <param name='uucp' doc='UUCP facility' />
+      </params>
+    </command>
+    <command id='log syslog local &lt;0-7&gt;'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='syslog' doc='Logging via syslog' />
+        <param name='local' doc='Syslog LOCAL facility' />
+        <param name='&lt;0-7&gt;' doc='Local facility number' />
+      </params>
+    </command>
+    <command id='no log syslog'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='syslog' doc='Logging via syslog' />
+      </params>
+    </command>
+    <command id='log gsmtap [HOSTNAME]'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='gsmtap' doc='Logging via GSMTAP' />
+        <param name='[HOSTNAME]' doc='Host name to send the GSMTAP logging to (UDP port 4729)' />
+      </params>
+    </command>
+    <command id='stats reporter statsd'>
+      <params>
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='reporter' doc='Configure a stats reporter' />
+        <param name='statsd' doc='Report to a STATSD server' />
+      </params>
+    </command>
+    <command id='no stats reporter statsd'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='reporter' doc='Configure a stats reporter' />
+        <param name='statsd' doc='Report to a STATSD server' />
+      </params>
+    </command>
+    <command id='stats reporter log'>
+      <params>
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='reporter' doc='Configure a stats reporter' />
+        <param name='log' doc='Report to the logger' />
+      </params>
+    </command>
+    <command id='no stats reporter log'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='reporter' doc='Configure a stats reporter' />
+        <param name='log' doc='Report to the logger' />
+      </params>
+    </command>
+    <command id='stats interval &lt;1-65535&gt;'>
+      <params>
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='interval' doc='Set the reporting interval' />
+        <param name='&lt;1-65535&gt;' doc='Interval in seconds' />
+      </params>
+    </command>
+    <command id='network'>
+      <params>
+        <param name='network' doc='Configure the GSM network' />
+      </params>
+    </command>
+    <command id='msc'>
+      <params>
+        <param name='msc' doc='Configure MSC options' />
+      </params>
+    </command>
+    <command id='mncc-int'>
+      <params>
+        <param name='mncc-int' doc='Configure internal MNCC handler' />
+      </params>
+    </command>
+    <command id='hlr'>
+      <params>
+        <param name='hlr' doc='Configure connection to the HLR' />
+      </params>
+    </command>
+    <command id='smpp'>
+      <params>
+        <param name='smpp' doc='Configure SMPP SMS Interface' />
+      </params>
+    </command>
+  </node>
+  <node id='config-log'>
+    <name>config-log</name>
+    <command id='logging filter all (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='all' doc='Do you want to log all messages?' />
+        <param name='0' doc='Only print messages matched by other filters' />
+        <param name='1' doc='Bypass filter and print all messages' />
+      </params>
+    </command>
+    <command id='logging color (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='color' doc='Configure color-printing for log messages' />
+        <param name='0' doc='Don&apos;t use color for printing messages' />
+        <param name='1' doc='Use color for printing messages' />
+      </params>
+    </command>
+    <command id='logging timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp' />
+      </params>
+    </command>
+    <command id='logging print extended-timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='extended-timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
+      </params>
+    </command>
+    <command id='logging print category (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem name' />
+      </params>
+    </command>
+    <command id='logging print category-hex (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category-hex' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem nr in hex (&apos;&lt;000b&gt;&apos;)' />
+      </params>
+    </command>
+    <command id='logging print level (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='level' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the log level name' />
+      </params>
+    </command>
+    <command id='logging print file (0|1|basename) [last]'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='file' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the source file and line' />
+        <param name='basename' doc='Prefix each log message with the source file&apos;s basename (strip leading paths) and line' />
+        <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' />
+      </params>
+    </command>
+    <command id='logging level (rll|cc|mm|rr|mncc|pag|msc|mgcp|ho|db|ref|ctrl|smpp|ranap|vlr|iucs|bssap|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf) (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='rll' doc='A-bis Radio Link Layer (RLL)' />
+        <param name='cc' doc='Layer3 Call Control (CC)' />
+        <param name='mm' doc='Layer3 Mobility Management (MM)' />
+        <param name='rr' doc='Layer3 Radio Resource (RR)' />
+        <param name='mncc' doc='MNCC API for Call Control application' />
+        <param name='pag' doc='Paging Subsystem' />
+        <param name='msc' doc='Mobile Switching Center' />
+        <param name='mgcp' doc='Media Gateway Control Protocol' />
+        <param name='ho' doc='Hand-Over' />
+        <param name='db' doc='Database Layer' />
+        <param name='ref' doc='Reference Counting' />
+        <param name='ctrl' doc='Control interface' />
+        <param name='smpp' doc='SMPP interface for external SMS apps' />
+        <param name='ranap' doc='Radio Access Network Application Part Protocol' />
+        <param name='vlr' doc='Visitor Location Register' />
+        <param name='iucs' doc='Iu-CS Protocol' />
+        <param name='bssap' doc='BSSAP Protocol (A Interface)' />
+        <param name='lglobal' doc='Library-internal global log family' />
+        <param name='llapd' doc='LAPD in libosmogsm' />
+        <param name='linp' doc='A-bis Intput Subsystem' />
+        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+        <param name='lmi' doc='A-bis Input Driver for Signalling' />
+        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+        <param name='lctrl' doc='Control Interface' />
+        <param name='lgtp' doc='GPRS GTP library' />
+        <param name='lstats' doc='Statistics messages and logging' />
+        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+        <param name='loap' doc='Osmocom Authentication Protocol' />
+        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+        <param name='ljibuf' doc='libosmo-netif Jitter Buffer' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level set-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level force-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the &apos;no logging level force-all&apos; command. Note: any &apos;logging level &lt;category&gt; &lt;level&gt;&apos; commands will have no visible effect after this, until the forced level is released.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='no logging level force-all'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Release any globally forced log level set with &apos;logging level force-all &lt;level&gt;&apos;' />
+      </params>
+    </command>
+    <command id='logging filter imsi IMSI'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='imsi' doc='Filter log messages by IMSI' />
+        <param name='IMSI' doc='IMSI to be used as filter' />
+      </params>
+    </command>
+  </node>
+  <node id='config-stats'>
+    <name>config-stats</name>
+    <command id='local-ip ADDR'>
+      <params>
+        <param name='local-ip' doc='Set the IP address to which we bind locally' />
+        <param name='ADDR' doc='IP Address' />
+      </params>
+    </command>
+    <command id='no local-ip'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='local-ip' doc='Set the IP address to which we bind locally' />
+      </params>
+    </command>
+    <command id='remote-ip ADDR'>
+      <params>
+        <param name='remote-ip' doc='Set the remote IP address to which we connect' />
+        <param name='ADDR' doc='IP Address' />
+      </params>
+    </command>
+    <command id='remote-port &lt;1-65535&gt;'>
+      <params>
+        <param name='remote-port' doc='Set the remote port to which we connect' />
+        <param name='&lt;1-65535&gt;' doc='Remote port number' />
+      </params>
+    </command>
+    <command id='mtu &lt;100-65535&gt;'>
+      <params>
+        <param name='mtu' doc='Set the maximum packet size' />
+        <param name='&lt;100-65535&gt;' doc='Size in byte' />
+      </params>
+    </command>
+    <command id='no mtu'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='mtu' doc='Set the maximum packet size' />
+      </params>
+    </command>
+    <command id='prefix PREFIX'>
+      <params>
+        <param name='prefix' doc='Set the item name prefix' />
+        <param name='PREFIX' doc='The prefix string' />
+      </params>
+    </command>
+    <command id='no prefix'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='prefix' doc='Set the item name prefix' />
+      </params>
+    </command>
+    <command id='level (global|peer|subscriber)'>
+      <params>
+        <param name='level' doc='Set the maximum group level' />
+        <param name='global' doc='Report global groups only' />
+        <param name='peer' doc='Report global and network peer related groups' />
+        <param name='subscriber' doc='Report global, peer, and subscriber groups' />
+      </params>
+    </command>
+    <command id='enable'>
+      <params>
+        <param name='enable' doc='Enable the reporter' />
+      </params>
+    </command>
+    <command id='disable'>
+      <params>
+        <param name='disable' doc='Disable the reporter' />
+      </params>
+    </command>
+  </node>
+  <node id='config-line'>
+    <name>config-line</name>
+    <command id='login'>
+      <params>
+        <param name='login' doc='Enable password checking' />
+      </params>
+    </command>
+    <command id='no login'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='login' doc='Enable password checking' />
+      </params>
+    </command>
+    <command id='bind A.B.C.D'>
+      <params>
+        <param name='bind' doc='Accept VTY telnet connections on local interface' />
+        <param name='A.B.C.D' doc='Local interface IP address (default: 127.0.0.1)' />
+      </params>
+    </command>
+  </node>
+  <node id='config-ctrl'>
+    <name>config-ctrl</name>
+    <command id='bind A.B.C.D'>
+      <params>
+        <param name='bind' doc='Set bind address to listen for Control connections' />
+        <param name='A.B.C.D' doc='Local IP address (default 127.0.0.1)' />
+      </params>
+    </command>
+  </node>
+  <node id='config-cs7'>
+    <name>config-cs7</name>
+    <command id='description .TEXT'>
+      <params>
+        <param name='description' doc='Save human-readable description of the object' />
+        <param name='.TEXT' doc='Text until the end of the line' />
+      </params>
+    </command>
+    <command id='network-indicator (international | national | reserved | spare)'>
+      <params>
+        <param name='network-indicator' doc='Configure the Network Indicator' />
+        <param name='international' doc='International Network' />
+        <param name='national' doc='National Network' />
+        <param name='reserved' doc='Reserved Network' />
+        <param name='spare' doc='Spare Network' />
+      </params>
+    </command>
+    <command id='point-code POINT_CODE'>
+      <params>
+        <param name='point-code' doc='Configure the local Point Code' />
+        <param name='POINT_CODE' doc='Point Code' />
+      </params>
+    </command>
+    <command id='point-code format &lt;1-24&gt; [&lt;1-23&gt;] [&lt;1-22&gt;]'>
+      <params>
+        <param name='point-code' doc='Point Code' />
+        <param name='format' doc='Configure Point Code Format' />
+        <param name='&lt;1-24&gt;' doc='Length of first PC component' />
+        <param name='[&lt;1-23&gt;]' doc='Length of second PC component' />
+        <param name='[&lt;1-22&gt;]' doc='Length of third PC component' />
+      </params>
+    </command>
+    <command id='point-code format default'>
+      <params>
+        <param name='point-code' doc='Point Code' />
+        <param name='format' doc='Configure Point Code Format' />
+        <param name='default' doc='Default Point Code Format (3.8.3)' />
+      </params>
+    </command>
+    <command id='point-code delimiter (default|dash)'>
+      <params>
+        <param name='point-code' doc='Point Code' />
+        <param name='delimiter' doc='Configure Point Code Delimiter' />
+        <param name='default' doc='Use dot as delimiter' />
+        <param name='dash' doc='User dash as delimiter' />
+      </params>
+    </command>
+    <command id='xua rkm routing-key-allocation (static-only|dynamic-permitted)'>
+      <params>
+        <param name='xua' doc='SIGTRAN xxxUA related' />
+        <param name='rkm' doc='Routing Key Management' />
+        <param name='routing-key-allocation' doc='Routing Key Management Allocation Policy' />
+        <param name='static-only' doc='Only static (pre-confgured) Routing Keys permitted' />
+        <param name='dynamic-permitted' doc='Dynamically allocate Routing Keys for what ASPs request' />
+      </params>
+    </command>
+    <command id='asp NAME &lt;0-65535&gt; &lt;0-65535&gt; (sua|m3ua|ipa)'>
+      <params>
+        <param name='asp' doc='Configure Application Server Process' />
+        <param name='NAME' doc='Name of ASP' />
+        <param name='&lt;0-65535&gt;' doc='Remote SCTP port number' />
+        <param name='&lt;0-65535&gt;' doc='Local SCTP port number' />
+        <param name='sua' doc='SCCP User Adaptation' />
+        <param name='m3ua' doc='MTP3 User Adaptation' />
+        <param name='ipa' doc='IPA Multiplex (SCCP Lite)' />
+      </params>
+    </command>
+    <command id='no asp NAME'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='asp' doc='Disable Application Server Process' />
+        <param name='NAME' doc='Name of ASP' />
+      </params>
+    </command>
+    <command id='as NAME (sua|m3ua|ipa)'>
+      <params>
+        <param name='as' doc='Configure an Application Server' />
+        <param name='NAME' doc='Name of the Application Server' />
+        <param name='sua' doc='SCCP User Adaptation' />
+        <param name='m3ua' doc='MTP3 User Adaptation' />
+        <param name='ipa' doc='IPA Multiplex (SCCP Lite)' />
+      </params>
+    </command>
+    <command id='no as NAME'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='as' doc='Disable Application Server' />
+        <param name='NAME' doc='Name of AS' />
+      </params>
+    </command>
+    <command id='sccp-address NAME'>
+      <params>
+        <param name='sccp-address' doc='Create/Modify an SCCP addressbook entry' />
+        <param name='NAME' doc='Name of the SCCP Address' />
+      </params>
+    </command>
+    <command id='no sccp-address NAME'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='sccp-address' doc='Delete an SCCP addressbook entry' />
+        <param name='NAME' doc='Name of the SCCP Address' />
+      </params>
+    </command>
+    <command id='sccp-timer (conn_est|ias|iar|rel|repeat_rel|int|guard|reset|reassembly) &lt;1-999999&gt;'>
+      <params>
+        <param name='sccp-timer' doc='Configure SCCP timer values, see ITU-T Q.714' />
+        <param name='conn_est' doc='Waiting for connection confirm message, 1 to 2 minutes (default: 60)' />
+        <param name='ias' doc='Send keep-alive: on an idle connection, delay before sending an Idle Timer message, 5 to 10 minutes (default: 420)' />
+        <param name='iar' doc='Receive keep-alive: on an idle connection, delay until considering a connection as stale, 11 to 21 minutes (default: 900)' />
+        <param name='rel' doc='Waiting for release complete message, 10 to 20 seconds (default: 10)' />
+        <param name='repeat_rel' doc='Waiting for release complete message; or to repeat sending released message after the initial expiry, 10 to 20 seconds (default: 10)' />
+        <param name='int' doc='Waiting for release complete message; or to release connection resources, freeze the LRN and alert a maintenance function after the initial expiry, extending to 1 minute (default: 60)' />
+        <param name='guard' doc='Waiting to resume normal procedure for temporary connection sections during the restart procedure, 23 to 25 minutes (default: 1380)' />
+        <param name='reset' doc='Waiting to release temporary connection section or alert maintenance function after reset request message is sent, 10 to 20 seconds (default: 10)' />
+        <param name='reassembly' doc='Waiting to receive all the segments of the remaining segments, single segmented message after receiving the first segment, 10 to 20 seconds (default: 10)' />
+        <param name='&lt;1-999999&gt;' doc='Timer value, in seconds' />
+      </params>
+    </command>
+  </node>
+  <node id='config-cs7-as'>
+    <name>config-cs7-as</name>
+    <command id='description .TEXT'>
+      <params>
+        <param name='description' doc='Save human-readable description of the object' />
+        <param name='.TEXT' doc='Text until the end of the line' />
+      </params>
+    </command>
+    <command id='asp NAME'>
+      <params>
+        <param name='asp' doc='Specify that a given ASP is part of this AS' />
+        <param name='NAME' doc='Name of ASP to be added to AS' />
+      </params>
+    </command>
+    <command id='no asp NAME'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='asp' doc='Specify ASP to be removed from this AS' />
+        <param name='NAME' doc='Name of ASP to be removed' />
+      </params>
+    </command>
+    <command id='traffic-mode (broadcast | loadshare | roundrobin | override)'>
+      <params>
+        <param name='traffic-mode' doc='Specifies traffic mode of operation of the ASP within the AS' />
+        <param name='broadcast' doc='Broadcast to all ASP within AS' />
+        <param name='loadshare' doc='Share Load among all ASP within AS' />
+        <param name='roundrobin' doc='Round-Robin between all ASP within AS' />
+        <param name='override' doc='Override' />
+      </params>
+    </command>
+    <command id='recovery-timeout &lt;1-2000&gt;'>
+      <params>
+        <param name='recovery-timeout' doc='Specifies the recovery timeout value in milliseconds' />
+        <param name='&lt;1-2000&gt;' doc='Recovery Timeout in Milliseconds' />
+      </params>
+    </command>
+    <command id='qos-class &lt;0-255&gt;'>
+      <params>
+        <param name='qos-class' doc='Specity QoS Class of AS' />
+        <param name='&lt;0-255&gt;' doc='QoS Class of AS' />
+      </params>
+    </command>
+    <command id='routing-key RCONTEXT DPC'>
+      <params>
+        <param name='routing-key' doc='Define a routing key' />
+        <param name='RCONTEXT' doc='Routing context number' />
+        <param name='DPC' doc='Destination Point Code' />
+      </params>
+    </command>
+    <command id='routing-key RCONTEXT DPC si (aal2|bicc|b-isup|h248|isup|sat-isup|sccp|tup)'>
+      <params>
+        <param name='routing-key' doc='Define a routing key' />
+        <param name='RCONTEXT' doc='Routing context number' />
+        <param name='DPC' doc='Destination Point Code' />
+        <param name='si' doc='Match on Service Indicator' />
+        <param name='aal2' doc='ATM Adaption Layer 2' />
+        <param name='bicc' doc='Bearer Independent Call Control' />
+        <param name='b-isup' doc='Broadband ISDN User Part' />
+        <param name='h248' doc='H.248' />
+        <param name='isup' doc='ISDN User Part' />
+        <param name='sat-isup' doc='Sattelite ISDN User Part' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='tup' doc='Telephony User Part' />
+      </params>
+    </command>
+    <command id='routing-key RCONTEXT DPC ssn SSN'>
+      <params>
+        <param name='routing-key' doc='Define a routing key' />
+        <param name='RCONTEXT' doc='Routing context number' />
+        <param name='DPC' doc='Destination Point Code' />
+        <param name='ssn' doc='Match on Sub-System Number' />
+        <param name='SSN' doc='Sub-System Number to match on' />
+      </params>
+    </command>
+    <command id='routing-key RCONTEXT DPC si (aal2|bicc|b-isup|h248|isup|sat-isup|sccp|tup) ssn SSN'>
+      <params>
+        <param name='routing-key' doc='Define a routing key' />
+        <param name='RCONTEXT' doc='Routing context number' />
+        <param name='DPC' doc='Destination Point Code' />
+        <param name='si' doc='Match on Service Indicator' />
+        <param name='aal2' doc='ATM Adaption Layer 2' />
+        <param name='bicc' doc='Bearer Independent Call Control' />
+        <param name='b-isup' doc='Broadband ISDN User Part' />
+        <param name='h248' doc='H.248' />
+        <param name='isup' doc='ISDN User Part' />
+        <param name='sat-isup' doc='Sattelite ISDN User Part' />
+        <param name='sccp' doc='Signalling Connection Control Part' />
+        <param name='tup' doc='Telephony User Part' />
+        <param name='ssn' doc='Match on Sub-System Number' />
+        <param name='SSN' doc='Sub-System Number to match on' />
+      </params>
+    </command>
+    <command id='point-code override dpc PC'>
+      <params>
+        <param name='point-code' doc='Point Code Specific Features' />
+        <param name='override' doc='Override (force) a point-code to hard-coded value' />
+        <param name='dpc' doc='Override Source Point Code' />
+        <param name='PC' doc='Override Destination Point Code' />
+      </params>
+    </command>
+  </node>
+  <node id='config-cs7-asp'>
+    <name>config-cs7-asp</name>
+    <command id='description .TEXT'>
+      <params>
+        <param name='description' doc='Save human-readable description of the object' />
+        <param name='.TEXT' doc='Text until the end of the line' />
+      </params>
+    </command>
+    <command id='remote-ip A.B.C.D'>
+      <params>
+        <param name='remote-ip' doc='Specify Remote IP Address of ASP' />
+        <param name='A.B.C.D' doc='Remote IP Address of ASP' />
+      </params>
+    </command>
+    <command id='local-ip A.B.C.D'>
+      <params>
+        <param name='local-ip' doc='Specify Local IP Address from which to contact ASP' />
+        <param name='A.B.C.D' doc='Local IP Address from which to contact of ASP' />
+      </params>
+    </command>
+    <command id='qos-class &lt;0-255&gt;'>
+      <params>
+        <param name='qos-class' doc='Specify QoS Class of ASP' />
+        <param name='&lt;0-255&gt;' doc='QoS Class of ASP' />
+      </params>
+    </command>
+    <command id='block'>
+      <params>
+        <param name='block' doc='Allows a SCTP Association with ASP, but doesn&apos;t let it become active' />
+      </params>
+    </command>
+    <command id='shutdown'>
+      <params>
+        <param name='shutdown' doc='Terminates SCTP association; New associations will be rejected' />
+      </params>
+    </command>
+  </node>
+  <node id='config-cs7-sccpaddr'>
+    <name>config-cs7-sccpaddr</name>
+    <command id='no point-code'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='point-code' doc='Remove point-code Number' />
+      </params>
+    </command>
+    <command id='no subsystem-number'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='subsystem-number' doc='Remove Subsystem Number' />
+      </params>
+    </command>
+    <command id='no global-title'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='global-title' doc='Remove Global Title' />
+      </params>
+    </command>
+    <command id='routing-indicator (GT|PC|IP)'>
+      <params>
+        <param name='routing-indicator' doc='Add Routing Indicator' />
+        <param name='GT' doc='by global-title' />
+        <param name='PC' doc='by point-code' />
+        <param name='IP' doc='by ip-address' />
+      </params>
+    </command>
+    <command id='point-code POINT_CODE'>
+      <params>
+        <param name='point-code' doc='Add point-code Number' />
+        <param name='POINT_CODE' doc='PC' />
+      </params>
+    </command>
+    <command id='subsystem-number &lt;0-4294967295&gt;'>
+      <params>
+        <param name='subsystem-number' doc='Add Subsystem Number' />
+        <param name='&lt;0-4294967295&gt;' doc='SSN' />
+      </params>
+    </command>
+    <command id='global-title'>
+      <params>
+        <param name='global-title' doc='Add/Modify Global Title' />
+      </params>
+    </command>
+  </node>
+  <node id='config-cs7-sccpaddr-gt'>
+    <name>config-cs7-sccpaddr-gt</name>
+    <command id='global-title-indicator &lt;0-15&gt;'>
+      <params>
+        <param name='global-title-indicator' doc='Set Global Title Indicator' />
+        <param name='&lt;0-15&gt;' doc='GTI' />
+      </params>
+    </command>
+    <command id='translation-type &lt;0-255&gt;'>
+      <params>
+        <param name='translation-type' doc='Set Global Title Translation Type' />
+        <param name='&lt;0-255&gt;' doc='TT' />
+      </params>
+    </command>
+    <command id='numbering-plan-indicator &lt;0-15&gt;'>
+      <params>
+        <param name='numbering-plan-indicator' doc='Set Global Title Numbering Plan Indicator' />
+        <param name='&lt;0-15&gt;' doc='NPI' />
+      </params>
+    </command>
+    <command id='nature-of-address-indicator &lt;0-127&gt;'>
+      <params>
+        <param name='nature-of-address-indicator' doc='Set Global Title Nature of Address Indicator' />
+        <param name='&lt;0-127&gt;' doc='NAI' />
+      </params>
+    </command>
+    <command id='digits DIGITS'>
+      <params>
+        <param name='digits' doc='Set Global Title Digits' />
+        <param name='DIGITS' doc='Number digits' />
+      </params>
+    </command>
+  </node>
+  <node id='config-net'>
+    <name>config-net</name>
+    <command id='network country code &lt;1-999&gt;'>
+      <params>
+        <param name='network' doc='Set the GSM network country code' />
+        <param name='country' doc='Country commands' />
+        <param name='code' doc='Code commands' />
+        <param name='&lt;1-999&gt;' doc='Network Country Code to use' />
+      </params>
+    </command>
+    <command id='mobile network code &lt;0-999&gt;'>
+      <params>
+        <param name='mobile' doc='Set the GSM mobile network code' />
+        <param name='network' doc='Network Commands' />
+        <param name='code' doc='Code commands' />
+        <param name='&lt;0-999&gt;' doc='Mobile Network Code to use' />
+      </params>
+    </command>
+    <command id='short name NAME'>
+      <params>
+        <param name='short' doc='Set the short GSM network name' />
+        <param name='name' doc='Name Commands' />
+        <param name='NAME' doc='Name to use' />
+      </params>
+    </command>
+    <command id='long name NAME'>
+      <params>
+        <param name='long' doc='Set the long GSM network name' />
+        <param name='name' doc='Name Commands' />
+        <param name='NAME' doc='Name to use' />
+      </params>
+    </command>
+    <command id='encryption a5 &lt;0-3&gt; [&lt;0-3&gt;] [&lt;0-3&gt;] [&lt;0-3&gt;]'>
+      <params>
+        <param name='encryption' doc='Encryption options' />
+        <param name='a5' doc='GSM A5 Air Interface Encryption' />
+        <param name='&lt;0-3&gt;' doc='A5/n Algorithm Number' />
+        <param name='[&lt;0-3&gt;]' doc='A5/n Algorithm Number' />
+        <param name='[&lt;0-3&gt;]' doc='A5/n Algorithm Number' />
+        <param name='[&lt;0-3&gt;]' doc='A5/n Algorithm Number' />
+      </params>
+    </command>
+    <command id='authentication (optional|required)'>
+      <params>
+        <param name='authentication' doc='Whether to enforce MS authentication in 2G' />
+        <param name='optional' doc='Allow MS to attach via 2G BSC without authentication' />
+        <param name='required' doc='Always do authentication' />
+      </params>
+    </command>
+    <command id='rrlp mode (none|ms-based|ms-preferred|ass-preferred)'>
+      <params>
+        <param name='rrlp' doc='Radio Resource Location Protocol' />
+        <param name='mode' doc='Set the Radio Resource Location Protocol Mode' />
+        <param name='none' doc='Don&apos;t send RRLP request' />
+        <param name='ms-based' doc='Request MS-based location' />
+        <param name='ms-preferred' doc='Request any location, prefer MS-based' />
+        <param name='ass-preferred' doc='Request any location, prefer MS-assisted' />
+      </params>
+    </command>
+    <command id='mm info (0|1)'>
+      <params>
+        <param name='mm' doc='Mobility Management' />
+        <param name='info' doc='Send MM INFO after LOC UPD ACCEPT' />
+        <param name='0' doc='Disable' />
+        <param name='1' doc='Enable' />
+      </params>
+    </command>
+    <command id='timezone &lt;-19-19&gt; (0|15|30|45)'>
+      <params>
+        <param name='timezone' doc='Set the Timezone Offset of the network' />
+        <param name='&lt;-19-19&gt;' doc='Timezone offset (hours)' />
+        <param name='0' doc='Timezone offset (00 minutes)' />
+        <param name='15' doc='Timezone offset (15 minutes)' />
+        <param name='30' doc='Timezone offset (30 minutes)' />
+        <param name='45' doc='Timezone offset (45 minutes)' />
+      </params>
+    </command>
+    <command id='timezone &lt;-19-19&gt; (0|15|30|45) &lt;0-2&gt;'>
+      <params>
+        <param name='timezone' doc='Set the Timezone Offset of the network' />
+        <param name='&lt;-19-19&gt;' doc='Timezone offset (hours)' />
+        <param name='0' doc='Timezone offset (00 minutes)' />
+        <param name='15' doc='Timezone offset (15 minutes)' />
+        <param name='30' doc='Timezone offset (30 minutes)' />
+        <param name='45' doc='Timezone offset (45 minutes)' />
+        <param name='&lt;0-2&gt;' doc='DST offset (hours)' />
+      </params>
+    </command>
+    <command id='no timezone'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='timezone' doc='Disable network timezone override, use system tz' />
+      </params>
+    </command>
+    <command id='periodic location update &lt;6-1530&gt;'>
+      <params>
+        <param name='periodic' doc='Periodic Location Updating Interval' />
+        <param name='location' doc='Periodic Location Updating Interval' />
+        <param name='update' doc='Periodic Location Updating Interval' />
+        <param name='&lt;6-1530&gt;' doc='Periodic Location Updating Interval in Minutes' />
+      </params>
+    </command>
+    <command id='no periodic location update'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='periodic' doc='Periodic Location Updating Interval' />
+        <param name='location' doc='Periodic Location Updating Interval' />
+        <param name='update' doc='Periodic Location Updating Interval' />
+      </params>
+    </command>
+  </node>
+  <node id='config-msc'>
+    <name>config-msc</name>
+    <command id='assign-tmsi'>
+      <params>
+        <param name='assign-tmsi' doc='Assign TMSI during Location Updating.' />
+      </params>
+    </command>
+    <command id='mncc-guard-timeout &lt;0-255&gt;'>
+      <params>
+        <param name='mncc-guard-timeout' doc='Set global guard timer for mncc interface activity' />
+        <param name='&lt;0-255&gt;' doc='guard timer value (sec.)' />
+      </params>
+    </command>
+    <command id='no assign-tmsi'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='assign-tmsi' doc='Assign TMSI during Location Updating.' />
+      </params>
+    </command>
+    <command id='auth-tuple-max-reuse-count &lt;-1-2147483647&gt;'>
+      <params>
+        <param name='auth-tuple-max-reuse-count' doc='Configure authentication tuple re-use' />
+        <param name='&lt;-1-2147483647&gt;' doc='0 to use each auth tuple at most once (default), &gt;0 to limit re-use, -1 to re-use infinitely (vulnerable!).' />
+      </params>
+    </command>
+    <command id='auth-tuple-reuse-on-error (0|1)'>
+      <params>
+        <param name='auth-tuple-reuse-on-error' doc='Configure authentication tuple re-use when HLR is not responsive' />
+        <param name='0' doc='0 = never re-use auth tuples beyond auth-tuple-max-reuse-count (default)' />
+        <param name='1' doc='1 = if the HLR does not deliver new tuples, do re-use already available old ones.' />
+      </params>
+    </command>
+    <command id='cs7-instance-a &lt;0-15&gt;'>
+      <params>
+        <param name='cs7-instance-a' doc='Set SS7 to be used by the A-Interface.' />
+        <param name='&lt;0-15&gt;' doc='SS7 instance reference number' />
+      </params>
+    </command>
+    <command id='cs7-instance-iu &lt;0-15&gt;'>
+      <params>
+        <param name='cs7-instance-iu' doc='Set SS7 to be used by the Iu-Interface.' />
+        <param name='&lt;0-15&gt;' doc='SS7 instance reference number' />
+      </params>
+    </command>
+    <command id='paging response-timer (default|&lt;1-65535&gt;)'>
+      <params>
+        <param name='paging' doc='Configure Paging' />
+        <param name='response-timer' doc='Set Paging timeout, the minimum time to pass between (unsuccessful) Pagings sent towards BSS or RNC' />
+        <param name='default' doc='Set to default timeout (10 seconds)' />
+        <param name='&lt;1-65535&gt;' doc='Set paging timeout in seconds' />
+      </params>
+    </command>
+    <command id='emergency-call route-to-msisdn MSISDN'>
+      <params>
+        <param name='emergency-call' doc='Configure Emergency Call Behaviour' />
+        <param name='route-to-msisdn' doc='MSISDN to which Emergency Calls are Dispatched' />
+        <param name='MSISDN' doc='MSISDN (E.164 Phone Number)' />
+      </params>
+    </command>
+    <command id='mgw local-ip A.B.C.D'>
+      <params>
+        <param name='mgw' doc='Configure MGCP connection to Media Gateway' />
+        <param name='local-ip' doc='local bind to connect to MGW from' />
+        <param name='A.B.C.D' doc='local bind IP address' />
+      </params>
+    </command>
+    <command id='mgw local-port &lt;0-65535&gt;'>
+      <params>
+        <param name='mgw' doc='Configure MGCP connection to Media Gateway' />
+        <param name='local-port' doc='local port to connect to MGW from' />
+        <param name='&lt;0-65535&gt;' doc='local bind port' />
+      </params>
+    </command>
+    <command id='mgw remote-ip A.B.C.D'>
+      <params>
+        <param name='mgw' doc='Configure MGCP connection to Media Gateway' />
+        <param name='remote-ip' doc='remote IP address to reach the MGW at' />
+        <param name='A.B.C.D' doc='remote IP address' />
+      </params>
+    </command>
+    <command id='mgw remote-port &lt;0-65535&gt;'>
+      <params>
+        <param name='mgw' doc='Configure MGCP connection to Media Gateway' />
+        <param name='remote-port' doc='remote port to reach the MGW at' />
+        <param name='&lt;0-65535&gt;' doc='remote port' />
+      </params>
+    </command>
+    <command id='mgw endpoint-range &lt;1-65534&gt; &lt;1-65534&gt;'>
+      <params>
+        <param name='mgw' doc='Configure MGCP connection to Media Gateway' />
+        <param name='endpoint-range' doc='usable range of endpoint identifiers' />
+        <param name='&lt;1-65534&gt;' doc='set first usable endpoint identifier' />
+        <param name='&lt;1-65534&gt;' doc='set last usable endpoint identifier' />
+      </params>
+    </command>
+    <command id='mgw bts-base &lt;0-65534&gt;'>
+      <params>
+        <param name='mgw' doc='Configure MGCP connection to Media Gateway' />
+        <param name='bts-base' doc='First UDP port allocated for the BTS side' />
+        <param name='&lt;0-65534&gt;' doc='UDP Port number' />
+      </params>
+    </command>
+    <command id='iu rab-assign-addr-enc (x213|v4raw)'>
+      <params>
+        <param name='iu' doc='Iu interface protocol options' />
+        <param name='rab-assign-addr-enc' doc='Choose RAB Assignment&apos;s Transport Layer Address encoding' />
+        <param name='x213' doc='ITU-T X.213 compliant address encoding (default)' />
+        <param name='v4raw' doc='32bit length raw IPv4 address (for ip.access nano3G)' />
+      </params>
+    </command>
+    <command id='asn1 debug (1|0)'>
+      <params>
+        <param name='asn1' doc='ASN.1 settings' />
+        <param name='debug' doc='Enable ASN.1 debug messages' />
+        <param name='1' doc='Log ASN.1 debug messages to stderr' />
+        <param name='0' doc='Do not log ASN.1 debug messages to stderr' />
+      </params>
+    </command>
+    <command id='asn1 xer-print (1|0)'>
+      <params>
+        <param name='asn1' doc='ASN.1 settings' />
+        <param name='xer-print' doc='Log human readable representations of all ASN.1 messages to stderr' />
+        <param name='1' doc='Log XML representation of all ASN.1 messages to stderr' />
+        <param name='0' doc='Do not log decoded ASN.1 messages to stderr' />
+      </params>
+    </command>
+  </node>
+  <node id='config-mncc-int'>
+    <name>config-mncc-int</name>
+    <command id='default-codec tch-f (fr|efr|amr)'>
+      <params>
+        <param name='default-codec' doc='Set default codec' />
+        <param name='tch-f' doc='Codec for TCH/F' />
+        <param name='fr' doc='Full-Rate' />
+        <param name='efr' doc='Enhanced Full-Rate' />
+        <param name='amr' doc='Adaptive Multi-Rate' />
+      </params>
+    </command>
+    <command id='default-codec tch-h (hr|amr)'>
+      <params>
+        <param name='default-codec' doc='Set default codec' />
+        <param name='tch-h' doc='Codec for TCH/H' />
+        <param name='hr' doc='Half-Rate' />
+        <param name='amr' doc='Adaptive Multi-Rate' />
+      </params>
+    </command>
+  </node>
+  <node id='config-smpp'>
+    <name>config-smpp</name>
+    <command id='smpp-first'>
+      <params>
+        <param name='smpp-first' doc='Try SMPP routes before the subscriber DB' />
+      </params>
+    </command>
+    <command id='no smpp-first'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='smpp-first' doc='Try SMPP before routes before the subscriber DB' />
+      </params>
+    </command>
+    <command id='local-tcp-port &lt;1-65535&gt;'>
+      <params>
+        <param name='local-tcp-port' doc='Set the local TCP port on which we listen for SMPP' />
+        <param name='&lt;1-65535&gt;' doc='TCP port number' />
+      </params>
+    </command>
+    <command id='local-tcp-ip A.B.C.D &lt;1-65535&gt;'>
+      <params>
+        <param name='local-tcp-ip' doc='Set the local IP address and TCP port on which we listen for SMPP' />
+        <param name='A.B.C.D' doc='Local IP address' />
+        <param name='&lt;1-65535&gt;' doc='TCP port number' />
+      </params>
+    </command>
+    <command id='system-id ID'>
+      <params>
+        <param name='system-id' doc='Set the System ID of this SMSC' />
+        <param name='ID' doc='Alphanumeric SMSC System ID' />
+      </params>
+    </command>
+    <command id='policy (accept-all|closed)'>
+      <params>
+        <param name='policy' doc='Set the authentication policy of this SMSC' />
+        <param name='accept-all' doc='Accept all SMPP connections independeint of system ID / passwd' />
+        <param name='closed' doc='Accept only SMPP connections from ESMEs explicitly configured' />
+      </params>
+    </command>
+    <command id='esme NAME'>
+      <params>
+        <param name='esme' doc='Configure a particular ESME' />
+        <param name='NAME' doc='Alphanumeric System ID of the ESME to be configured' />
+      </params>
+    </command>
+    <command id='no esme NAME'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='esme' doc='Remove ESME configuration' />
+        <param name='NAME' doc='Alphanumeric System ID of the ESME to be removed' />
+      </params>
+    </command>
+  </node>
+  <node id='config-smpp-esme'>
+    <name>config-smpp-esme</name>
+    <command id='password PASSWORD'>
+      <params>
+        <param name='password' doc='Set the password for this ESME' />
+        <param name='PASSWORD' doc='Alphanumeric password string' />
+      </params>
+    </command>    <command id='no password'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='password' doc='Remove the password for this ESME' />
+      </params>
+    </command>
+    <command id='route prefix (unknown|international|national|network|subscriber|alpha|abbrev) (unknown|isdn|x121|f69|e212|national|private|ermes|ip|wap) PREFIX'>
+      <params>
+        <param name='route' doc='Configure a route for MO-SMS to be sent to this ESME' />
+        <param name='prefix' doc='Prefix-match route' />
+        <param name='unknown' doc='Unknown type-of-number' />
+        <param name='international' doc='International type-of-number' />
+        <param name='national' doc='National type-of-number' />
+        <param name='network' doc='Network specific type-of-number' />
+        <param name='subscriber' doc='Subscriber type-of-number' />
+        <param name='alpha' doc='Alphanumeric type-of-number' />
+        <param name='abbrev' doc='Abbreviated type-of-number' />
+        <param name='unknown' doc='Unknown numbering plan' />
+        <param name='isdn' doc='ISDN (E.164) numbering plan' />
+        <param name='x121' doc='X.121 numbering plan' />
+        <param name='f69' doc='F.69 numbering plan' />
+        <param name='e212' doc='E.212 numbering plan' />
+        <param name='national' doc='National numbering plan' />
+        <param name='private' doc='Private numbering plan' />
+        <param name='ermes' doc='ERMES numbering plan' />
+        <param name='ip' doc='IP numbering plan' />
+        <param name='wap' doc='WAP numbeing plan' />
+        <param name='PREFIX' doc='Destination number prefix' />
+      </params>
+    </command>
+    <command id='no route prefix (unknown|international|national|network|subscriber|alpha|abbrev) (unknown|isdn|x121|f69|e212|national|private|ermes|ip|wap) PREFIX'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='route' doc='Configure a route for MO-SMS to be sent to this ESME' />
+        <param name='prefix' doc='Prefix-match route' />
+        <param name='unknown' doc='Unknown type-of-number' />
+        <param name='international' doc='International type-of-number' />
+        <param name='national' doc='National type-of-number' />
+        <param name='network' doc='Network specific type-of-number' />
+        <param name='subscriber' doc='Subscriber type-of-number' />
+        <param name='alpha' doc='Alphanumeric type-of-number' />
+        <param name='abbrev' doc='Abbreviated type-of-number' />
+        <param name='unknown' doc='Unknown numbering plan' />
+        <param name='isdn' doc='ISDN (E.164) numbering plan' />
+        <param name='x121' doc='X.121 numbering plan' />
+        <param name='f69' doc='F.69 numbering plan' />
+        <param name='e212' doc='E.212 numbering plan' />
+        <param name='national' doc='National numbering plan' />
+        <param name='private' doc='Private numbering plan' />
+        <param name='ermes' doc='ERMES numbering plan' />
+        <param name='ip' doc='IP numbering plan' />
+        <param name='wap' doc='WAP numbeing plan' />
+        <param name='PREFIX' doc='Destination number prefix' />
+      </params>
+    </command>
+    <command id='default-route'>
+      <params>
+        <param name='default-route' doc='Set this ESME as default-route for all SMS to unknown destinations' />
+      </params>
+    </command>
+    <command id='no default-route'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='default-route' doc='Remove this ESME as default-route for all SMS to unknown destinations' />
+      </params>
+    </command>
+    <command id='deliver-src-imsi'>
+      <params>
+        <param name='deliver-src-imsi' doc='Enable the use of IMSI as source address in DELIVER' />
+      </params>
+    </command>
+    <command id='no deliver-src-imsi'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='deliver-src-imsi' doc='Disable the use of IMSI as source address in DELIVER' />
+      </params>
+    </command>
+    <command id='osmocom-extensions'>
+      <params>
+        <param name='osmocom-extensions' doc='Enable the use of Osmocom SMPP Extensions for this ESME' />
+      </params>
+    </command>
+    <command id='no osmocom-extensions'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='osmocom-extensions' doc='Disable the use of Osmocom SMPP Extensions for this ESME' />
+      </params>
+    </command>
+    <command id='dcs-transparent'>
+      <params>
+        <param name='dcs-transparent' doc='Enable the transparent pass-through of TP-DCS to SMPP DataCoding' />
+      </params>
+    </command>
+    <command id='no dcs-transparent'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='dcs-transparent' doc='Disable the transparent pass-through of TP-DCS to SMPP DataCoding' />
+      </params>
+    </command>
+  </node>
+  <node id='config-hlr'>
+    <name>config-hlr</name>
+    <command id='remote-ip A.B.C.D'>
+      <params>
+        <param name='remote-ip' doc='Remote GSUP address of the HLR' />
+        <param name='A.B.C.D' doc='Remote GSUP address (default: 127.0.0.1)' />
+      </params>
+    </command>
+    <command id='remote-port &lt;1-65535&gt;'>
+      <params>
+        <param name='remote-port' doc='Remote GSUP port of the HLR' />
+        <param name='&lt;1-65535&gt;' doc='Remote GSUP port (default: MSC_HLR_REMOTE_PORT_DEFAULT)' />
+      </params>
+    </command>
+  </node>
+</vtydoc>