smpp: refactor initialization, add bind address
Make the SMPP bind address configurable (used to be harcoded as "0.0.0.0").
Add VTY command
smpp
local-tcp A.B.C.D <1-65535>
while keeping the old command 'local-tcp-port <1-65535>'. Both the old and the
new command immediately change the SMPP listening address and port.
Add a LOGL_NOTICE log when the SMPP listening address and/or port change.
However, to be useful, this patch has to go somewhat further: refactor the
initialization procedure, because it was impossible to run the VTY commands
without an already established connection.
The SMPP initialization procedure was weird. It would first open a connection
on the default port, and a subsequent VTY port reconfiguration while reading
the config file would try to re-establish a connection on a different port. If
that failed, smpp would switch back to the default port instead of failing the
program launch as the user would expect. If anything else ran on port 2775,
SMPP would thus refuse to launch despite the config file having a different
port: the first bind would always happen on 0.0.0.0:2775. Change that.
In the VTY commands, merely store address and port if no fd is established yet.
Introduce several SMPP initialization stages:
* allocate struct and initialize pointers,
* then read config file without immediately starting to listen,
* and once the main program is ready, start listening.
After that, the VTY command behaves as before: try to re-establish the old
connection if the newly supplied address and port don't work out. I'm not
actually sure why this switch-back behavior is needed, but fair enough.
In detail, replace the function
smpp_smsc_init()
with the various steps
smpp_smsc_alloc_init() -- prepare struct for VTY commands
smpp_smsc_conf() -- set addr an port only, for reading the config file
smpp_smsc_start() -- establish a first connection, for main()
smpp_smsc_restart() -- switch running connection, for telnet VTY
smpp_smsc_stop() -- tear down connection, used by _start() twice
And replace
smpp_openbsc_init()
smpp_openbsc_set_net()
with
smpp_openbsc_alloc_init()
smpp_openbsc_start()
I'd have picked function names like "_bind"/"_unbind", but in the SMPP protocol
there is also a bind/unbind process, so instead I chose the names "_start",
"_restart" and "_stop".
The smsc struct used to be talloc'd outside of smpp_smsc_init(). Since the smsc
code internally uses talloc anyway and employs the smsc struct as talloc
context, I decided to enforce talloc allocation within smpp_smsc_alloc_init().
Be stricter about osmo_signal_register_handler() return codes.
diff --git a/openbsc/src/libmsc/smpp_smsc.h b/openbsc/src/libmsc/smpp_smsc.h
index 3dd6562..bd20137 100644
--- a/openbsc/src/libmsc/smpp_smsc.h
+++ b/openbsc/src/libmsc/smpp_smsc.h
@@ -89,6 +89,7 @@
struct llist_head esme_list;
struct llist_head acl_list;
struct llist_head route_list;
+ const char *bind_addr;
uint16_t listen_port;
char system_id[SMPP_SYS_ID_LEN+1];
int accept_all;
@@ -100,7 +101,11 @@
int smpp_addr_eq(const struct osmo_smpp_addr *a,
const struct osmo_smpp_addr *b);
-int smpp_smsc_init(struct smsc *smsc, uint16_t port);
+struct smsc *smpp_smsc_alloc_init(void *ctx);
+int smpp_smsc_conf(struct smsc *smsc, const char *bind_addr, uint16_t port);
+int smpp_smsc_start(struct smsc *smsc, const char *bind_addr, uint16_t port);
+int smpp_smsc_restart(struct smsc *smsc, const char *bind_addr, uint16_t port);
+void smpp_smsc_stop(struct smsc *smsc);
void smpp_esme_get(struct osmo_esme *esme);
void smpp_esme_put(struct osmo_esme *esme);