OsmoGGSN: Add VTY reference manual
Change-Id: Iddf6fe26689172d7db001198943c816eaaed7931
diff --git a/doc/manuals/Makefile b/doc/manuals/Makefile
index daf3597..2dfedb2 100644
--- a/doc/manuals/Makefile
+++ b/doc/manuals/Makefile
@@ -1,6 +1,18 @@
# XSL stylesheets downloaded from http://docbook.sourceforge.net/release/xsl/current/html/
# Makefile from BitBake/OpenEmbedded manuals
+EXTRA_DEPS = gen-ggsn-vty-docbook
+
+topdir = .
+ggsn_reference = $(topdir)/osmoggsn-vty-reference.xml
+manuals = $(ggsn_reference)
+# types = pdf txt rtf ps xhtml html man tex texi dvi
+# types = pdf txt
+types = $(docbooktotypes)
+docbooktotypes = pdf
+# htmlcssfile =
+# htmlcss =
+
TOPDIR := ..
ASCIIDOCS := osmoggsn-usermanual
@@ -10,4 +22,18 @@
osmoggsn-usermanual.pdf: chapters/*.adoc
clean:
- rm -rf $(cleanfiles)
+ -rm -rf $(cleanfiles)
+ -rm osmoggsn-usermanual__*.svg osmoggsn-usermanual__*.png
+ -rm osmoggsn-usermanual.check
+
+gen-ggsn-vty-docbook: FORCE
+ $(call command,xsltproc -o generated/combined1.xml \
+ --stringparam with $(PWD)/../common/vty_additions.xml \
+ $(MERGE_DOC) vty/ggsn_vty_reference.xml, \
+ XSLTPROC,Merging Common VTY)
+ $(call command,xsltproc -o generated/combined2.xml \
+ --stringparam with $(PWD)/vty/ggsn_vty_additions.xml \
+ $(MERGE_DOC) generated/combined1.xml, \
+ XSLTPROC,Merging GGSN VTY)
+ $(call command,xsltproc ../vty_reference.xsl generated/combined2.xml > generated/docbook_vty.xml, \
+ XSLTPROC,Converting GGSN VTY to DocBook)
diff --git a/doc/manuals/osmoggsn-vty-reference.xml b/doc/manuals/osmoggsn-vty-reference.xml
new file mode 100644
index 0000000..44e7bfc
--- /dev/null
+++ b/doc/manuals/osmoggsn-vty-reference.xml
@@ -0,0 +1,38 @@
+<?xml version="1.0" encoding="UTF-8"?>
+<!--
+ ex:ts=2:sw=42sts=2:et
+ -*- tab-width: 4; c-basic-offset: 4; indent-tabs-mode: nil -*-
+-->
+<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook V5.0//EN"
+"http://www.docbook.org/xml/5.0/dtd/docbook.dtd" [
+<!ENTITY chapter-vty SYSTEM "../common/chapters/vty.xml" >
+<!ENTITY sections-vty SYSTEM "generated/docbook_vty.xml" >
+]>
+
+<book>
+ <info>
+ <revhistory>
+ <revision>
+ <revnumber>v1</revnumber>
+ <date>06th September 2017</date>
+ <authorinitials>hw</authorinitials>
+ <revremark>Initial version as of OsmoGGSN v1.0.0</revremark>
+ </revision>
+ </revhistory>
+
+ <title>OsmoGGSN VTY Reference</title>
+
+ <copyright>
+ <year>2017</year>
+ </copyright>
+
+ <legalnotice>
+ <para>This work is copyright by <orgname>sysmocom - s.f.m.c. GmbH</orgname>. All rights reserved.
+ </para>
+ </legalnotice>
+ </info>
+
+ <!-- Main chapters-->
+ &chapter-vty;
+</book>
+
diff --git a/doc/manuals/vty/ggsn_vty_additions.xml b/doc/manuals/vty/ggsn_vty_additions.xml
new file mode 100644
index 0000000..1bbeb81
--- /dev/null
+++ b/doc/manuals/vty/ggsn_vty_additions.xml
@@ -0,0 +1,30 @@
+<vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'>
+ <node id="9">
+ <child_of nodeid='4' />
+ <name>Telnet/VTY Configuration Node</name>
+ <description>
+ Configure parameters of the Telnet/VTY Interface, such as to which IP address it should bind/listen to.
+ </description>
+ </node>
+ <node id="14">
+ <child_of nodeid='4' />
+ <name>CTRL Configuration Node</name>
+ <description>
+ Configure parameters of the CTRL Interface, such as to which IP address it should bind/listen to.
+ </description>
+ </node>
+ <node id="26">
+ <child_of nodeid='4' />
+ <name>GGSN Instance Configuration Node</name>
+ <description>
+ Configure an Instance of a (virtual) GGSN
+ </description>
+ </node>
+ <node id="27">
+ <child_of nodeid='26' />
+ <name>APN Configuration Node</name>
+ <description>
+ Configure an Access Point Name (APN) inside a GGSN Instance
+ </description>
+ </node>
+</vtydoc>
diff --git a/doc/manuals/vty/ggsn_vty_reference.xml b/doc/manuals/vty/ggsn_vty_reference.xml
new file mode 100644
index 0000000..6809ead
--- /dev/null
+++ b/doc/manuals/vty/ggsn_vty_reference.xml
@@ -0,0 +1,1480 @@
+<vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'>
+ <node id='0'>
+ </node>
+ <node id='1'>
+ <command id='show version'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='version' doc='Displays program version' />
+ </params>
+ </command>
+ <command id='show online-help'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='online-help' doc='Online help' />
+ </params>
+ </command>
+ <command id='list'>
+ <params>
+ <param name='list' doc='Print command list' />
+ </params>
+ </command>
+ <command id='exit'>
+ <params>
+ <param name='exit' doc='Exit current mode and down to previous mode' />
+ </params>
+ </command>
+ <command id='help'>
+ <params>
+ <param name='help' doc='Description of the interactive help system' />
+ </params>
+ </command>
+ <command id='enable'>
+ <params>
+ <param name='enable' doc='Turn on privileged mode command' />
+ </params>
+ </command>
+ <command id='terminal length <0-512>'>
+ <params>
+ <param name='terminal' doc='Set terminal line parameters' />
+ <param name='length' doc='Set number of lines on a screen' />
+ <param name='<0-512>' doc='Number of lines on screen (0 for no pausing)' />
+ </params>
+ </command>
+ <command id='terminal no length'>
+ <params>
+ <param name='terminal' doc='Set terminal line parameters' />
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='length' doc='Set number of lines on a screen' />
+ </params>
+ </command>
+ <command id='echo .MESSAGE'>
+ <params>
+ <param name='echo' doc='Echo a message back to the vty' />
+ <param name='.MESSAGE' doc='The message to echo' />
+ </params>
+ </command>
+ <command id='who'>
+ <params>
+ <param name='who' doc='Display who is on vty' />
+ </params>
+ </command>
+ <command id='show history'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='history' doc='Display the session command history' />
+ </params>
+ </command>
+ <command id='logging enable'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='enable' doc='Enables logging to this vty' />
+ </params>
+ </command>
+ <command id='logging disable'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='disable' doc='Disables logging to this vty' />
+ </params>
+ </command>
+ <command id='logging filter all (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='filter' doc='Filter log messages' />
+ <param name='all' doc='Do you want to log all messages?' />
+ <param name='0' doc='Only print messages matched by other filters' />
+ <param name='1' doc='Bypass filter and print all messages' />
+ </params>
+ </command>
+ <command id='logging color (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='color' doc='Configure color-printing for log messages' />
+ <param name='0' doc='Don't use color for printing messages' />
+ <param name='1' doc='Use color for printing messages' />
+ </params>
+ </command>
+ <command id='logging timestamp (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='timestamp' doc='Configure log message timestamping' />
+ <param name='0' doc='Don't prefix each log message' />
+ <param name='1' doc='Prefix each log message with current timestamp' />
+ </params>
+ </command>
+ <command id='logging print extended-timestamp (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='print' doc='Log output settings' />
+ <param name='extended-timestamp' doc='Configure log message timestamping' />
+ <param name='0' doc='Don't prefix each log message' />
+ <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
+ </params>
+ </command>
+ <command id='logging print category (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='print' doc='Log output settings' />
+ <param name='category' doc='Configure log message' />
+ <param name='0' doc='Don't prefix each log message' />
+ <param name='1' doc='Prefix each log message with category/subsystem name' />
+ </params>
+ </command>
+ <command id='logging set-log-mask MASK'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='set-log-mask' doc='Set the logmask of this logging target' />
+ <param name='MASK' doc='The logmask to use' />
+ </params>
+ </command>
+ <command id='logging set log mask MASK'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='set' doc='Decide which categories to output.' />
+ <param name='log' doc='Log commands' />
+ <param name='mask' doc='Mask commands' />
+ <param name='MASK' doc='The logmask to use' />
+ </params>
+ </command>
+ <command id='logging level (all|ip|tun|ggsn|sgsn|icmp6|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp) (everything|debug|info|notice|error|fatal)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='level' doc='Set the log level for a specified category' />
+ <param name='all' doc='Global setting for all subsystems' />
+ <param name='ip' doc='IP Pool and other groups' />
+ <param name='tun' doc='Tunnel interface' />
+ <param name='ggsn' doc='GGSN' />
+ <param name='sgsn' doc='SGSN Emulator' />
+ <param name='icmp6' doc='ICMPv6' />
+ <param name='lglobal' doc='Library-internal global log family' />
+ <param name='llapd' doc='LAPD in libosmogsm' />
+ <param name='linp' doc='A-bis Intput Subsystem' />
+ <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+ <param name='lmi' doc='A-bis Input Driver for Signalling' />
+ <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+ <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+ <param name='lctrl' doc='Control Interface' />
+ <param name='lgtp' doc='GPRS GTP library' />
+ <param name='lstats' doc='Statistics messages and logging' />
+ <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+ <param name='loap' doc='Osmocom Authentication Protocol' />
+ <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+ <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+ <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+ <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+ <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+ <param name='everything' doc='Don't use. It doesn't log anything' />
+ <param name='debug' doc='Log debug messages and higher levels' />
+ <param name='info' doc='Log informational messages and higher levels' />
+ <param name='notice' doc='Log noticeable messages and higher levels' />
+ <param name='error' doc='Log error messages and higher levels' />
+ <param name='fatal' doc='Log only fatal messages' />
+ </params>
+ </command>
+ <command id='show logging vty'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='logging' doc='Show current logging configuration' />
+ <param name='vty' doc='Show current logging configuration for this vty' />
+ </params>
+ </command>
+ <command id='show alarms'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='alarms' doc='Show current logging configuration' />
+ </params>
+ </command>
+ <command id='show stats'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='stats' doc='Show statistical values' />
+ </params>
+ </command>
+ <command id='show stats level (global|peer|subscriber)'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='stats' doc='Show statistical values' />
+ <param name='level' doc='Set the maximum group level' />
+ <param name='global' doc='Show global groups only' />
+ <param name='peer' doc='Show global and network peer related groups' />
+ <param name='subscriber' doc='Show global, peer, and subscriber groups' />
+ </params>
+ </command>
+ <command id='show asciidoc counters'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='asciidoc' doc='Asciidoc generation' />
+ <param name='counters' doc='Generate table of all registered counters' />
+ </params>
+ </command>
+ <command id='show pdp-context ggsn NAME [apn APN]'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='pdp-context' doc='Show PDP Context Information' />
+ <param name='ggsn' doc='Gateway GPRS Support NODE (GGSN)' />
+ <param name='NAME' doc='GGSN Name' />
+ <param name='[apn' doc='(null)' />
+ <param name='APN]' doc='(null)' />
+ </params>
+ </command>
+ <command id='show pdp-context imsi IMSI [<0-15>]'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='pdp-context' doc='Display information on PDP Context' />
+ <param name='imsi' doc='PDP contexts for given IMSI' />
+ <param name='IMSI' doc='PDP context for given NSAPI' />
+ <param name='[<0-15>]' doc='(null)' />
+ </params>
+ </command>
+ <command id='show ggsn [NAME]'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='ggsn' doc='Display information on the GGSN' />
+ <param name='[NAME]' doc='(null)' />
+ </params>
+ </command>
+ </node>
+ <node id='2'>
+ </node>
+ <node id='3'>
+ <command id='help'>
+ <params>
+ <param name='help' doc='Description of the interactive help system' />
+ </params>
+ </command>
+ <command id='list'>
+ <params>
+ <param name='list' doc='Print command list' />
+ </params>
+ </command>
+ <command id='write terminal'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='terminal' doc='Write to terminal' />
+ </params>
+ </command>
+ <command id='write file'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='file' doc='Write to configuration file' />
+ </params>
+ </command>
+ <command id='write memory'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='memory' doc='Write configuration to the file (same as write file)' />
+ </params>
+ </command>
+ <command id='write'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ </params>
+ </command>
+ <command id='show running-config'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='running-config' doc='running configuration' />
+ </params>
+ </command>
+ <command id='exit'>
+ <params>
+ <param name='exit' doc='Exit current mode and down to previous mode' />
+ </params>
+ </command>
+ <command id='disable'>
+ <params>
+ <param name='disable' doc='Turn off privileged mode command' />
+ </params>
+ </command>
+ <command id='configure terminal'>
+ <params>
+ <param name='configure' doc='Configuration from vty interface' />
+ <param name='terminal' doc='Configuration terminal' />
+ </params>
+ </command>
+ <command id='copy running-config startup-config'>
+ <params>
+ <param name='copy' doc='Copy configuration' />
+ <param name='running-config' doc='Copy running config to... ' />
+ <param name='startup-config' doc='Copy running config to startup config (same as write file)' />
+ </params>
+ </command>
+ <command id='show startup-config'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='startup-config' doc='Contentes of startup configuration' />
+ </params>
+ </command>
+ <command id='show version'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='version' doc='Displays program version' />
+ </params>
+ </command>
+ <command id='show online-help'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='online-help' doc='Online help' />
+ </params>
+ </command>
+ <command id='terminal length <0-512>'>
+ <params>
+ <param name='terminal' doc='Set terminal line parameters' />
+ <param name='length' doc='Set number of lines on a screen' />
+ <param name='<0-512>' doc='Number of lines on screen (0 for no pausing)' />
+ </params>
+ </command>
+ <command id='terminal no length'>
+ <params>
+ <param name='terminal' doc='Set terminal line parameters' />
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='length' doc='Set number of lines on a screen' />
+ </params>
+ </command>
+ <command id='echo .MESSAGE'>
+ <params>
+ <param name='echo' doc='Echo a message back to the vty' />
+ <param name='.MESSAGE' doc='The message to echo' />
+ </params>
+ </command>
+ <command id='who'>
+ <params>
+ <param name='who' doc='Display who is on vty' />
+ </params>
+ </command>
+ <command id='show history'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='history' doc='Display the session command history' />
+ </params>
+ </command>
+ <command id='terminal monitor'>
+ <params>
+ <param name='terminal' doc='Set terminal line parameters' />
+ <param name='monitor' doc='Copy debug output to the current terminal line' />
+ </params>
+ </command>
+ <command id='terminal no monitor'>
+ <params>
+ <param name='terminal' doc='Set terminal line parameters' />
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='monitor' doc='Copy debug output to the current terminal line' />
+ </params>
+ </command>
+ <command id='logging enable'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='enable' doc='Enables logging to this vty' />
+ </params>
+ </command>
+ <command id='logging disable'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='disable' doc='Disables logging to this vty' />
+ </params>
+ </command>
+ <command id='logging filter all (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='filter' doc='Filter log messages' />
+ <param name='all' doc='Do you want to log all messages?' />
+ <param name='0' doc='Only print messages matched by other filters' />
+ <param name='1' doc='Bypass filter and print all messages' />
+ </params>
+ </command>
+ <command id='logging color (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='color' doc='Configure color-printing for log messages' />
+ <param name='0' doc='Don't use color for printing messages' />
+ <param name='1' doc='Use color for printing messages' />
+ </params>
+ </command>
+ <command id='logging timestamp (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='timestamp' doc='Configure log message timestamping' />
+ <param name='0' doc='Don't prefix each log message' />
+ <param name='1' doc='Prefix each log message with current timestamp' />
+ </params>
+ </command>
+ <command id='logging print extended-timestamp (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='print' doc='Log output settings' />
+ <param name='extended-timestamp' doc='Configure log message timestamping' />
+ <param name='0' doc='Don't prefix each log message' />
+ <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
+ </params>
+ </command>
+ <command id='logging print category (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='print' doc='Log output settings' />
+ <param name='category' doc='Configure log message' />
+ <param name='0' doc='Don't prefix each log message' />
+ <param name='1' doc='Prefix each log message with category/subsystem name' />
+ </params>
+ </command>
+ <command id='logging set-log-mask MASK'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='set-log-mask' doc='Set the logmask of this logging target' />
+ <param name='MASK' doc='The logmask to use' />
+ </params>
+ </command>
+ <command id='logging set log mask MASK'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='set' doc='Decide which categories to output.' />
+ <param name='log' doc='Log commands' />
+ <param name='mask' doc='Mask commands' />
+ <param name='MASK' doc='The logmask to use' />
+ </params>
+ </command>
+ <command id='logging level (all|ip|tun|ggsn|sgsn|icmp6|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp) (everything|debug|info|notice|error|fatal)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='level' doc='Set the log level for a specified category' />
+ <param name='all' doc='Global setting for all subsystems' />
+ <param name='ip' doc='IP Pool and other groups' />
+ <param name='tun' doc='Tunnel interface' />
+ <param name='ggsn' doc='GGSN' />
+ <param name='sgsn' doc='SGSN Emulator' />
+ <param name='icmp6' doc='ICMPv6' />
+ <param name='lglobal' doc='Library-internal global log family' />
+ <param name='llapd' doc='LAPD in libosmogsm' />
+ <param name='linp' doc='A-bis Intput Subsystem' />
+ <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+ <param name='lmi' doc='A-bis Input Driver for Signalling' />
+ <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+ <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+ <param name='lctrl' doc='Control Interface' />
+ <param name='lgtp' doc='GPRS GTP library' />
+ <param name='lstats' doc='Statistics messages and logging' />
+ <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+ <param name='loap' doc='Osmocom Authentication Protocol' />
+ <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+ <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+ <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+ <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+ <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+ <param name='everything' doc='Don't use. It doesn't log anything' />
+ <param name='debug' doc='Log debug messages and higher levels' />
+ <param name='info' doc='Log informational messages and higher levels' />
+ <param name='notice' doc='Log noticeable messages and higher levels' />
+ <param name='error' doc='Log error messages and higher levels' />
+ <param name='fatal' doc='Log only fatal messages' />
+ </params>
+ </command>
+ <command id='show logging vty'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='logging' doc='Show current logging configuration' />
+ <param name='vty' doc='Show current logging configuration for this vty' />
+ </params>
+ </command>
+ <command id='show alarms'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='alarms' doc='Show current logging configuration' />
+ </params>
+ </command>
+ <command id='show stats'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='stats' doc='Show statistical values' />
+ </params>
+ </command>
+ <command id='show stats level (global|peer|subscriber)'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='stats' doc='Show statistical values' />
+ <param name='level' doc='Set the maximum group level' />
+ <param name='global' doc='Show global groups only' />
+ <param name='peer' doc='Show global and network peer related groups' />
+ <param name='subscriber' doc='Show global, peer, and subscriber groups' />
+ </params>
+ </command>
+ <command id='show asciidoc counters'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='asciidoc' doc='Asciidoc generation' />
+ <param name='counters' doc='Generate table of all registered counters' />
+ </params>
+ </command>
+ <command id='show pdp-context ggsn NAME [apn APN]'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='pdp-context' doc='Show PDP Context Information' />
+ <param name='ggsn' doc='Gateway GPRS Support NODE (GGSN)' />
+ <param name='NAME' doc='GGSN Name' />
+ <param name='[apn' doc='(null)' />
+ <param name='APN]' doc='(null)' />
+ </params>
+ </command>
+ <command id='show pdp-context imsi IMSI [<0-15>]'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='pdp-context' doc='Display information on PDP Context' />
+ <param name='imsi' doc='PDP contexts for given IMSI' />
+ <param name='IMSI' doc='PDP context for given NSAPI' />
+ <param name='[<0-15>]' doc='(null)' />
+ </params>
+ </command>
+ <command id='show ggsn [NAME]'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='ggsn' doc='Display information on the GGSN' />
+ <param name='[NAME]' doc='(null)' />
+ </params>
+ </command>
+ </node>
+ <node id='4'>
+ <command id='help'>
+ <params>
+ <param name='help' doc='Description of the interactive help system' />
+ </params>
+ </command>
+ <command id='list'>
+ <params>
+ <param name='list' doc='Print command list' />
+ </params>
+ </command>
+ <command id='write terminal'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='terminal' doc='Write to terminal' />
+ </params>
+ </command>
+ <command id='write file'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='file' doc='Write to configuration file' />
+ </params>
+ </command>
+ <command id='write memory'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='memory' doc='Write configuration to the file (same as write file)' />
+ </params>
+ </command>
+ <command id='write'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ </params>
+ </command>
+ <command id='show running-config'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='running-config' doc='running configuration' />
+ </params>
+ </command>
+ <command id='exit'>
+ <params>
+ <param name='exit' doc='Exit current mode and down to previous mode' />
+ </params>
+ </command>
+ <command id='end'>
+ <params>
+ <param name='end' doc='End current mode and change to enable mode.' />
+ </params>
+ </command>
+ <command id='hostname WORD'>
+ <params>
+ <param name='hostname' doc='Set system's network name' />
+ <param name='WORD' doc='This system's network name' />
+ </params>
+ </command>
+ <command id='no hostname [HOSTNAME]'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='hostname' doc='Reset system's network name' />
+ <param name='[HOSTNAME]' doc='Host name of this router' />
+ </params>
+ </command>
+ <command id='password (8|) WORD'>
+ <params>
+ <param name='password' doc='Assign the terminal connection password' />
+ <param name='8' doc='Specifies a HIDDEN password will follow' />
+ <param name='' doc='dummy string ' />
+ <param name='WORD' doc='The HIDDEN line password string' />
+ </params>
+ </command>
+ <command id='password LINE'>
+ <params>
+ <param name='password' doc='Assign the terminal connection password' />
+ <param name='LINE' doc='The UNENCRYPTED (cleartext) line password' />
+ </params>
+ </command>
+ <command id='enable password (8|) WORD'>
+ <params>
+ <param name='enable' doc='Modify enable password parameters' />
+ <param name='password' doc='Assign the privileged level password' />
+ <param name='8' doc='Specifies a HIDDEN password will follow' />
+ <param name='' doc='dummy string ' />
+ <param name='WORD' doc='The HIDDEN 'enable' password string' />
+ </params>
+ </command>
+ <command id='enable password LINE'>
+ <params>
+ <param name='enable' doc='Modify enable password parameters' />
+ <param name='password' doc='Assign the privileged level password' />
+ <param name='LINE' doc='The UNENCRYPTED (cleartext) 'enable' password' />
+ </params>
+ </command>
+ <command id='no enable password'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='enable' doc='Modify enable password parameters' />
+ <param name='password' doc='Assign the privileged level password' />
+ </params>
+ </command>
+ <command id='banner motd default'>
+ <params>
+ <param name='banner' doc='Set banner string' />
+ <param name='motd' doc='Strings for motd' />
+ <param name='default' doc='Default string' />
+ </params>
+ </command>
+ <command id='banner motd file [FILE]'>
+ <params>
+ <param name='banner' doc='Set banner' />
+ <param name='motd' doc='Banner for motd' />
+ <param name='file' doc='Banner from a file' />
+ <param name='[FILE]' doc='Filename' />
+ </params>
+ </command>
+ <command id='no banner motd'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='banner' doc='Set banner string' />
+ <param name='motd' doc='Strings for motd' />
+ </params>
+ </command>
+ <command id='service terminal-length <0-512>'>
+ <params>
+ <param name='service' doc='Set up miscellaneous service' />
+ <param name='terminal-length' doc='System wide terminal length configuration' />
+ <param name='<0-512>' doc='Number of lines of VTY (0 means no line control)' />
+ </params>
+ </command>
+ <command id='no service terminal-length [<0-512>]'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='service' doc='Set up miscellaneous service' />
+ <param name='terminal-length' doc='System wide terminal length configuration' />
+ <param name='[<0-512>]' doc='Number of lines of VTY (0 means no line control)' />
+ </params>
+ </command>
+ <command id='line vty'>
+ <params>
+ <param name='line' doc='Configure a terminal line' />
+ <param name='vty' doc='Virtual terminal' />
+ </params>
+ </command>
+ <command id='service advanced-vty'>
+ <params>
+ <param name='service' doc='Set up miscellaneous service' />
+ <param name='advanced-vty' doc='Enable advanced mode vty interface' />
+ </params>
+ </command>
+ <command id='no service advanced-vty'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='service' doc='Set up miscellaneous service' />
+ <param name='advanced-vty' doc='Enable advanced mode vty interface' />
+ </params>
+ </command>
+ <command id='show history'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='history' doc='Display the session command history' />
+ </params>
+ </command>
+ <command id='log stderr'>
+ <params>
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='stderr' doc='Logging via STDERR of the process' />
+ </params>
+ </command>
+ <command id='no log stderr'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='stderr' doc='Logging via STDERR of the process' />
+ </params>
+ </command>
+ <command id='log file .FILENAME'>
+ <params>
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='file' doc='Logging to text file' />
+ <param name='.FILENAME' doc='Filename' />
+ </params>
+ </command>
+ <command id='no log file .FILENAME'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='file' doc='Logging to text file' />
+ <param name='.FILENAME' doc='Filename' />
+ </params>
+ </command>
+ <command id='log alarms <2-32700>'>
+ <params>
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='alarms' doc='Logging alarms to osmo_strrb' />
+ <param name='<2-32700>' doc='Maximum number of messages to log' />
+ </params>
+ </command>
+ <command id='no log alarms'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='alarms' doc='Logging alarms to osmo_strrb' />
+ </params>
+ </command>
+ <command id='log syslog (authpriv|cron|daemon|ftp|lpr|mail|news|user|uucp)'>
+ <params>
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='syslog' doc='Logging via syslog' />
+ <param name='authpriv' doc='Security/authorization messages facility' />
+ <param name='cron' doc='Clock daemon (cron/at) facility' />
+ <param name='daemon' doc='General system daemon facility' />
+ <param name='ftp' doc='Ftp daemon facility' />
+ <param name='lpr' doc='Line printer facility' />
+ <param name='mail' doc='Mail facility' />
+ <param name='news' doc='News facility' />
+ <param name='user' doc='Generic facility' />
+ <param name='uucp' doc='UUCP facility' />
+ </params>
+ </command>
+ <command id='log syslog local <0-7>'>
+ <params>
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='syslog' doc='Logging via syslog' />
+ <param name='local' doc='Syslog LOCAL facility' />
+ <param name='<0-7>' doc='Local facility number' />
+ </params>
+ </command>
+ <command id='no log syslog'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='syslog' doc='Logging via syslog' />
+ </params>
+ </command>
+ <command id='log gsmtap [HOSTNAME]'>
+ <params>
+ <param name='log' doc='Configure logging sub-system' />
+ <param name='gsmtap' doc='Logging via GSMTAP' />
+ <param name='[HOSTNAME]' doc='Host name to send the GSMTAP logging to (UDP port 4729)' />
+ </params>
+ </command>
+ <command id='stats reporter statsd'>
+ <params>
+ <param name='stats' doc='Configure stats sub-system' />
+ <param name='reporter' doc='Configure a stats reporter' />
+ <param name='statsd' doc='Report to a STATSD server' />
+ </params>
+ </command>
+ <command id='no stats reporter statsd'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='stats' doc='Configure stats sub-system' />
+ <param name='reporter' doc='Configure a stats reporter' />
+ <param name='statsd' doc='Report to a STATSD server' />
+ </params>
+ </command>
+ <command id='stats reporter log'>
+ <params>
+ <param name='stats' doc='Configure stats sub-system' />
+ <param name='reporter' doc='Configure a stats reporter' />
+ <param name='log' doc='Report to the logger' />
+ </params>
+ </command>
+ <command id='no stats reporter log'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='stats' doc='Configure stats sub-system' />
+ <param name='reporter' doc='Configure a stats reporter' />
+ <param name='log' doc='Report to the logger' />
+ </params>
+ </command>
+ <command id='stats interval <1-65535>'>
+ <params>
+ <param name='stats' doc='Configure stats sub-system' />
+ <param name='interval' doc='Set the reporting interval' />
+ <param name='<1-65535>' doc='Interval in seconds' />
+ </params>
+ </command>
+ <command id='ggsn NAME'>
+ <params>
+ <param name='ggsn' doc='Configure the Gateway GPRS Support Node' />
+ <param name='NAME' doc='GGSN Name (has only local significance)' />
+ </params>
+ </command>
+ <command id='no ggsn NAME'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='ggsn' doc='Remove the named Gateway GPRS Support Node' />
+ <param name='NAME' doc='GGSN Name (has only local significance)' />
+ </params>
+ </command>
+ <command id='ctrl'>
+ <params>
+ <param name='ctrl' doc='Configure the Control Interface' />
+ </params>
+ </command>
+ </node>
+ <node id='7'>
+ <command id='help'>
+ <params>
+ <param name='help' doc='Description of the interactive help system' />
+ </params>
+ </command>
+ <command id='list'>
+ <params>
+ <param name='list' doc='Print command list' />
+ </params>
+ </command>
+ <command id='write terminal'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='terminal' doc='Write to terminal' />
+ </params>
+ </command>
+ <command id='write file'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='file' doc='Write to configuration file' />
+ </params>
+ </command>
+ <command id='write memory'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='memory' doc='Write configuration to the file (same as write file)' />
+ </params>
+ </command>
+ <command id='write'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ </params>
+ </command>
+ <command id='show running-config'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='running-config' doc='running configuration' />
+ </params>
+ </command>
+ <command id='exit'>
+ <params>
+ <param name='exit' doc='Exit current mode and down to previous mode' />
+ </params>
+ </command>
+ <command id='end'>
+ <params>
+ <param name='end' doc='End current mode and change to enable mode.' />
+ </params>
+ </command>
+ <command id='logging filter all (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='filter' doc='Filter log messages' />
+ <param name='all' doc='Do you want to log all messages?' />
+ <param name='0' doc='Only print messages matched by other filters' />
+ <param name='1' doc='Bypass filter and print all messages' />
+ </params>
+ </command>
+ <command id='logging color (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='color' doc='Configure color-printing for log messages' />
+ <param name='0' doc='Don't use color for printing messages' />
+ <param name='1' doc='Use color for printing messages' />
+ </params>
+ </command>
+ <command id='logging timestamp (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='timestamp' doc='Configure log message timestamping' />
+ <param name='0' doc='Don't prefix each log message' />
+ <param name='1' doc='Prefix each log message with current timestamp' />
+ </params>
+ </command>
+ <command id='logging print extended-timestamp (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='print' doc='Log output settings' />
+ <param name='extended-timestamp' doc='Configure log message timestamping' />
+ <param name='0' doc='Don't prefix each log message' />
+ <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
+ </params>
+ </command>
+ <command id='logging print category (0|1)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='print' doc='Log output settings' />
+ <param name='category' doc='Configure log message' />
+ <param name='0' doc='Don't prefix each log message' />
+ <param name='1' doc='Prefix each log message with category/subsystem name' />
+ </params>
+ </command>
+ <command id='logging level (all|ip|tun|ggsn|sgsn|icmp6|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp) (everything|debug|info|notice|error|fatal)'>
+ <params>
+ <param name='logging' doc='Configure log message to this terminal' />
+ <param name='level' doc='Set the log level for a specified category' />
+ <param name='all' doc='Global setting for all subsystems' />
+ <param name='ip' doc='IP Pool and other groups' />
+ <param name='tun' doc='Tunnel interface' />
+ <param name='ggsn' doc='GGSN' />
+ <param name='sgsn' doc='SGSN Emulator' />
+ <param name='icmp6' doc='ICMPv6' />
+ <param name='lglobal' doc='Library-internal global log family' />
+ <param name='llapd' doc='LAPD in libosmogsm' />
+ <param name='linp' doc='A-bis Intput Subsystem' />
+ <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+ <param name='lmi' doc='A-bis Input Driver for Signalling' />
+ <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+ <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+ <param name='lctrl' doc='Control Interface' />
+ <param name='lgtp' doc='GPRS GTP library' />
+ <param name='lstats' doc='Statistics messages and logging' />
+ <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+ <param name='loap' doc='Osmocom Authentication Protocol' />
+ <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+ <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+ <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+ <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+ <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+ <param name='everything' doc='Don't use. It doesn't log anything' />
+ <param name='debug' doc='Log debug messages and higher levels' />
+ <param name='info' doc='Log informational messages and higher levels' />
+ <param name='notice' doc='Log noticeable messages and higher levels' />
+ <param name='error' doc='Log error messages and higher levels' />
+ <param name='fatal' doc='Log only fatal messages' />
+ </params>
+ </command>
+ </node>
+ <node id='8'>
+ <command id='help'>
+ <params>
+ <param name='help' doc='Description of the interactive help system' />
+ </params>
+ </command>
+ <command id='list'>
+ <params>
+ <param name='list' doc='Print command list' />
+ </params>
+ </command>
+ <command id='write terminal'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='terminal' doc='Write to terminal' />
+ </params>
+ </command>
+ <command id='write file'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='file' doc='Write to configuration file' />
+ </params>
+ </command>
+ <command id='write memory'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='memory' doc='Write configuration to the file (same as write file)' />
+ </params>
+ </command>
+ <command id='write'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ </params>
+ </command>
+ <command id='show running-config'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='running-config' doc='running configuration' />
+ </params>
+ </command>
+ <command id='exit'>
+ <params>
+ <param name='exit' doc='Exit current mode and down to previous mode' />
+ </params>
+ </command>
+ <command id='end'>
+ <params>
+ <param name='end' doc='End current mode and change to enable mode.' />
+ </params>
+ </command>
+ <command id='local-ip ADDR'>
+ <params>
+ <param name='local-ip' doc='Set the IP address to which we bind locally' />
+ <param name='ADDR' doc='IP Address' />
+ </params>
+ </command>
+ <command id='no local-ip'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='local-ip' doc='Set the IP address to which we bind locally' />
+ </params>
+ </command>
+ <command id='remote-ip ADDR'>
+ <params>
+ <param name='remote-ip' doc='Set the remote IP address to which we connect' />
+ <param name='ADDR' doc='IP Address' />
+ </params>
+ </command>
+ <command id='remote-port <1-65535>'>
+ <params>
+ <param name='remote-port' doc='Set the remote port to which we connect' />
+ <param name='<1-65535>' doc='Remote port number' />
+ </params>
+ </command>
+ <command id='mtu <100-65535>'>
+ <params>
+ <param name='mtu' doc='Set the maximum packet size' />
+ <param name='<100-65535>' doc='Size in byte' />
+ </params>
+ </command>
+ <command id='no mtu'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='mtu' doc='Set the maximum packet size' />
+ </params>
+ </command>
+ <command id='prefix PREFIX'>
+ <params>
+ <param name='prefix' doc='Set the item name prefix' />
+ <param name='PREFIX' doc='The prefix string' />
+ </params>
+ </command>
+ <command id='no prefix'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='prefix' doc='Set the item name prefix' />
+ </params>
+ </command>
+ <command id='level (global|peer|subscriber)'>
+ <params>
+ <param name='level' doc='Set the maximum group level' />
+ <param name='global' doc='Report global groups only' />
+ <param name='peer' doc='Report global and network peer related groups' />
+ <param name='subscriber' doc='Report global, peer, and subscriber groups' />
+ </params>
+ </command>
+ <command id='enable'>
+ <params>
+ <param name='enable' doc='Enable the reporter' />
+ </params>
+ </command>
+ <command id='disable'>
+ <params>
+ <param name='disable' doc='Disable the reporter' />
+ </params>
+ </command>
+ </node>
+ <node id='9'>
+ <command id='help'>
+ <params>
+ <param name='help' doc='Description of the interactive help system' />
+ </params>
+ </command>
+ <command id='list'>
+ <params>
+ <param name='list' doc='Print command list' />
+ </params>
+ </command>
+ <command id='write terminal'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='terminal' doc='Write to terminal' />
+ </params>
+ </command>
+ <command id='write file'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='file' doc='Write to configuration file' />
+ </params>
+ </command>
+ <command id='write memory'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='memory' doc='Write configuration to the file (same as write file)' />
+ </params>
+ </command>
+ <command id='write'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ </params>
+ </command>
+ <command id='show running-config'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='running-config' doc='running configuration' />
+ </params>
+ </command>
+ <command id='exit'>
+ <params>
+ <param name='exit' doc='Exit current mode and down to previous mode' />
+ </params>
+ </command>
+ <command id='end'>
+ <params>
+ <param name='end' doc='End current mode and change to enable mode.' />
+ </params>
+ </command>
+ <command id='login'>
+ <params>
+ <param name='login' doc='Enable password checking' />
+ </params>
+ </command>
+ <command id='no login'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='login' doc='Enable password checking' />
+ </params>
+ </command>
+ <command id='bind A.B.C.D'>
+ <params>
+ <param name='bind' doc='Accept VTY telnet connections on local interface' />
+ <param name='A.B.C.D' doc='Local interface IP address (default: 127.0.0.1)' />
+ </params>
+ </command>
+ </node>
+ <node id='14'>
+ <command id='bind A.B.C.D'>
+ <params>
+ <param name='bind' doc='Set bind address to listen for Control connections' />
+ <param name='A.B.C.D' doc='Local IP address (default 127.0.0.1)' />
+ </params>
+ </command>
+ </node>
+ <node id='26'>
+ <command id='help'>
+ <params>
+ <param name='help' doc='Description of the interactive help system' />
+ </params>
+ </command>
+ <command id='list'>
+ <params>
+ <param name='list' doc='Print command list' />
+ </params>
+ </command>
+ <command id='write terminal'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='terminal' doc='Write to terminal' />
+ </params>
+ </command>
+ <command id='write file'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='file' doc='Write to configuration file' />
+ </params>
+ </command>
+ <command id='write memory'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='memory' doc='Write configuration to the file (same as write file)' />
+ </params>
+ </command>
+ <command id='write'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ </params>
+ </command>
+ <command id='show running-config'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='running-config' doc='running configuration' />
+ </params>
+ </command>
+ <command id='exit'>
+ <params>
+ <param name='exit' doc='Exit current mode and down to previous mode' />
+ </params>
+ </command>
+ <command id='end'>
+ <params>
+ <param name='end' doc='End current mode and change to enable mode.' />
+ </params>
+ </command>
+ <command id='description .TEXT'>
+ <params>
+ <param name='description' doc='Save human-readable description of the object' />
+ <param name='.TEXT' doc='Text until the end of the line' />
+ </params>
+ </command>
+ <command id='no description'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='description' doc='Remove description of the object' />
+ </params>
+ </command>
+ <command id='shutdown ggsn'>
+ <params>
+ <param name='shutdown' doc='Put the GGSN in administrative shut-down' />
+ <param name='ggsn' doc='Gateway GPRS Support NODE (GGSN)' />
+ </params>
+ </command>
+ <command id='no shutdown ggsn'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='shutdown' doc='Gateway GPRS Support NODE (GGSN)' />
+ <param name='ggsn' doc='Remove the GGSN from administrative shut-down' />
+ </params>
+ </command>
+ <command id='gtp bind-ip A.B.C.D'>
+ <params>
+ <param name='gtp' doc='GTP Parameters' />
+ <param name='bind-ip' doc='Set the IP address for the local GTP bind' />
+ <param name='A.B.C.D' doc='IPv4 Address' />
+ </params>
+ </command>
+ <command id='gtp control-ip A.B.C.D'>
+ <params>
+ <param name='gtp' doc='GTP Parameters' />
+ <param name='control-ip' doc='Set the IP address states as local IP in GTP-C messages' />
+ <param name='A.B.C.D' doc='IPv4 Address' />
+ </params>
+ </command>
+ <command id='gtp user-ip A.B.C.D'>
+ <params>
+ <param name='gtp' doc='GTP Parameters' />
+ <param name='user-ip' doc='Set the IP address states as local IP in GTP-U messages' />
+ <param name='A.B.C.D' doc='IPv4 Address' />
+ </params>
+ </command>
+ <command id='gtp state-dir PATH'>
+ <params>
+ <param name='gtp' doc='GTP Parameters' />
+ <param name='state-dir' doc='Set the directory for the GTP State file' />
+ <param name='PATH' doc='Local Directory' />
+ </params>
+ </command>
+ <command id='apn NAME'>
+ <params>
+ <param name='apn' doc='APN Configuration' />
+ <param name='NAME' doc='APN Name' />
+ </params>
+ </command>
+ <command id='no apn NAME'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='apn' doc='Remove APN Configuration' />
+ <param name='NAME' doc='APN Name' />
+ </params>
+ </command>
+ <command id='default-apn NAME'>
+ <params>
+ <param name='default-apn' doc='Set a default-APN to be used if no other APN matches' />
+ <param name='NAME' doc='APN Name' />
+ </params>
+ </command>
+ <command id='no default-apn'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='default-apn' doc='Remove default-APN to be used if no other APN matches' />
+ </params>
+ </command>
+ </node>
+ <node id='27'>
+ <command id='help'>
+ <params>
+ <param name='help' doc='Description of the interactive help system' />
+ </params>
+ </command>
+ <command id='list'>
+ <params>
+ <param name='list' doc='Print command list' />
+ </params>
+ </command>
+ <command id='write terminal'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='terminal' doc='Write to terminal' />
+ </params>
+ </command>
+ <command id='write file'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='file' doc='Write to configuration file' />
+ </params>
+ </command>
+ <command id='write memory'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ <param name='memory' doc='Write configuration to the file (same as write file)' />
+ </params>
+ </command>
+ <command id='write'>
+ <params>
+ <param name='write' doc='Write running configuration to memory, network, or terminal' />
+ </params>
+ </command>
+ <command id='show running-config'>
+ <params>
+ <param name='show' doc='Show running system information' />
+ <param name='running-config' doc='running configuration' />
+ </params>
+ </command>
+ <command id='exit'>
+ <params>
+ <param name='exit' doc='Exit current mode and down to previous mode' />
+ </params>
+ </command>
+ <command id='end'>
+ <params>
+ <param name='end' doc='End current mode and change to enable mode.' />
+ </params>
+ </command>
+ <command id='description .TEXT'>
+ <params>
+ <param name='description' doc='Save human-readable description of the object' />
+ <param name='.TEXT' doc='Text until the end of the line' />
+ </params>
+ </command>
+ <command id='no description'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='description' doc='Remove description of the object' />
+ </params>
+ </command>
+ <command id='shutdown'>
+ <params>
+ <param name='shutdown' doc='Put the APN in administrative shut-down' />
+ </params>
+ </command>
+ <command id='no shutdown'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='shutdown' doc='Remove the APN from administrative shut-down' />
+ </params>
+ </command>
+ <command id='gtpu-mode (tun|kernel-gtp)'>
+ <params>
+ <param name='gtpu-mode' doc='Set the Mode for this APN (tun or Linux Kernel GTP)' />
+ <param name='tun' doc='GTP-U in userspace using TUN device' />
+ <param name='kernel-gtp' doc='GTP-U in kernel using Linux Kernel GTP' />
+ </params>
+ </command>
+ <command id='type-support (v4|v6|v4v6)'>
+ <params>
+ <param name='type-support' doc='Enable support for PDP Type' />
+ <param name='v4' doc='IPv4(-only) PDP Type' />
+ <param name='v6' doc='IPv6(-only) PDP Type' />
+ <param name='v4v6' doc='IPv4v6 (dual-stack) PDP Type' />
+ </params>
+ </command>
+ <command id='no type-support (v4|v6|v4v6)'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='type-support' doc='Disable support for PDP Type' />
+ <param name='v4' doc='IPv4(-only) PDP Type' />
+ <param name='v6' doc='IPv6(-only) PDP Type' />
+ <param name='v4v6' doc='IPv4v6 (dual-stack) PDP Type' />
+ </params>
+ </command>
+ <command id='tun-device NAME'>
+ <params>
+ <param name='tun-device' doc='Configure tun device name' />
+ <param name='NAME' doc='TUN device name' />
+ </params>
+ </command>
+ <command id='ipup-script PATH'>
+ <params>
+ <param name='ipup-script' doc='Configure name/path of ip-up script' />
+ <param name='PATH' doc='File/Path name of ip-up script' />
+ </params>
+ </command>
+ <command id='no ipup-script'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='ipup-script' doc='Disable ip-up script' />
+ </params>
+ </command>
+ <command id='ipdown-script PATH'>
+ <params>
+ <param name='ipdown-script' doc='Configure name/path of ip-down script' />
+ <param name='PATH' doc='File/Path name of ip-down script' />
+ </params>
+ </command>
+ <command id='no ipdown-script'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='ipdown-script' doc='Disable ip-down script' />
+ </params>
+ </command>
+ <command id='ip prefix (static|dynamic) A.B.C.D/M'>
+ <params>
+ <param name='ip' doc='IP information' />
+ <param name='prefix' doc='Prefix (Network/Netmask)' />
+ <param name='static' doc='IPv4 Adress/Prefix-Length' />
+ <param name='dynamic' doc='(null)' />
+ <param name='A.B.C.D/M' doc='(null)' />
+ </params>
+ </command>
+ <command id='ipv6 prefix (static|dynamic) X:X::X:X/M'>
+ <params>
+ <param name='ipv6' doc='IPv6 Information' />
+ <param name='prefix' doc='Prefix (Network/Netmask)' />
+ <param name='static' doc='IPv6 Address/Prefix-Length' />
+ <param name='dynamic' doc='(null)' />
+ <param name='X:X::X:X/M' doc='(null)' />
+ </params>
+ </command>
+ <command id='ip dns <0-1> A.B.C.D'>
+ <params>
+ <param name='ip' doc='IP information' />
+ <param name='dns' doc='Configure DNS Server' />
+ <param name='<0-1>' doc='primary/secondary DNS' />
+ <param name='A.B.C.D' doc='IP address of DNS Sever' />
+ </params>
+ </command>
+ <command id='ipv6 dns <0-1> X:X::X:X'>
+ <params>
+ <param name='ipv6' doc='IPv6 Information' />
+ <param name='dns' doc='Configure DNS Server' />
+ <param name='<0-1>' doc='primary/secondary DNS' />
+ <param name='X:X::X:X' doc='IP address of DNS Sever' />
+ </params>
+ </command>
+ <command id='no (ip|ipv6) dns <0-1>'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='ip' doc='IP information' />
+ <param name='ipv6' doc='IPv6 Information' />
+ <param name='dns' doc='Disable DNS Server' />
+ <param name='<0-1>' doc='primary/secondary DNS' />
+ </params>
+ </command>
+ <command id='ip ifconfig A.B.C.D/M'>
+ <params>
+ <param name='ip' doc='IP information' />
+ <param name='ifconfig' doc='GGSN-based interface configuration' />
+ <param name='A.B.C.D/M' doc='IPv4 Adress/Prefix-Length' />
+ </params>
+ </command>
+ <command id='no ip ifconfig'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='ip' doc='IP information' />
+ <param name='ifconfig' doc='GGSN-based interface configuration' />
+ </params>
+ </command>
+ <command id='ipv6 ifconfig X:X::X:X/M'>
+ <params>
+ <param name='ipv6' doc='IPv6 Information' />
+ <param name='ifconfig' doc='GGSN-based interface configuration' />
+ <param name='X:X::X:X/M' doc='IPv6 Adress/Prefix-Length' />
+ </params>
+ </command>
+ <command id='no ipv6 ifconfig'>
+ <params>
+ <param name='no' doc='Negate a command or set its defaults' />
+ <param name='ipv6' doc='IPv6 Information' />
+ <param name='ifconfig' doc='GGSN-based interface configuration' />
+ </params>
+ </command>
+ </node>
+</vtydoc>
\ No newline at end of file