diff --git a/doc/manuals/vty-osmogbproxy/gbproxy_vty_additions.xml b/doc/manuals/vty-osmogbproxy/gbproxy_vty_additions.xml
new file mode 100644
index 0000000..6da2d2f
--- /dev/null
+++ b/doc/manuals/vty-osmogbproxy/gbproxy_vty_additions.xml
@@ -0,0 +1,5 @@
+<vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'>
+    <node id='config-gbproxy'>
+	    <description>Configure the Gb proxy</description>
+    </node>
+</vtydoc>
diff --git a/doc/manuals/vty-osmogbproxy/gbproxy_vty_reference.xml b/doc/manuals/vty-osmogbproxy/gbproxy_vty_reference.xml
new file mode 100644
index 0000000..1db3c0d
--- /dev/null
+++ b/doc/manuals/vty-osmogbproxy/gbproxy_vty_reference.xml
@@ -0,0 +1,1627 @@
+<vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'>
+  <node id='_common_cmds_'>
+    <name>Common Commands</name>
+    <description>These commands are available on all VTY nodes. They are listed here only once, to unclutter the VTY reference.</description>
+    <command id='help'>
+      <params>
+        <param name='help' doc='Description of the interactive help system' />
+      </params>
+    </command>
+    <command id='list'>
+      <params>
+        <param name='list' doc='Print command list' />
+      </params>
+    </command>
+    <command id='write terminal'>
+      <params>
+        <param name='write' doc='Write running configuration to memory, network, or terminal' />
+        <param name='terminal' doc='Write to terminal' />
+      </params>
+    </command>
+    <command id='write file [PATH]'>
+      <params>
+        <param name='write' doc='Write running configuration to memory, network, or terminal' />
+        <param name='file' doc='Write to configuration file' />
+        <param name='[PATH]' doc='Set file path to store the config, or replace if already exists' />
+      </params>
+    </command>
+    <command id='write memory'>
+      <params>
+        <param name='write' doc='Write running configuration to memory, network, or terminal' />
+        <param name='memory' doc='Write configuration to the file (same as write file)' />
+      </params>
+    </command>
+    <command id='write'>
+      <params>
+        <param name='write' doc='Write running configuration to memory, network, or terminal' />
+      </params>
+    </command>
+    <command id='show running-config'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='running-config' doc='running configuration' />
+      </params>
+    </command>
+    <command id='exit'>
+      <params>
+        <param name='exit' doc='Exit current mode and down to previous mode' />
+      </params>
+    </command>
+    <command id='end'>
+      <params>
+        <param name='end' doc='End current mode and change to enable mode.' />
+      </params>
+    </command>
+  </node>
+  <node id='view'>
+    <name>view</name>
+    <command id='show version'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='version' doc='Displays program version' />
+      </params>
+    </command>
+    <command id='show online-help'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='online-help' doc='Online help' />
+      </params>
+    </command>
+    <command id='enable'>
+      <params>
+        <param name='enable' doc='Turn on privileged mode command' />
+      </params>
+    </command>
+    <command id='terminal length &lt;0-512&gt;'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='length' doc='Set number of lines on a screen' />
+        <param name='&lt;0-512&gt;' doc='Number of lines on screen (0 for no pausing)' />
+      </params>
+    </command>
+    <command id='terminal no length'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='length' doc='Set number of lines on a screen' />
+      </params>
+    </command>
+    <command id='who'>
+      <params>
+        <param name='who' doc='Display who is on vty' />
+      </params>
+    </command>
+    <command id='show history'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='history' doc='Display the session command history' />
+      </params>
+    </command>
+    <command id='logging enable'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='enable' doc='Enables logging to this vty' />
+      </params>
+    </command>
+    <command id='logging disable'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='disable' doc='Disables logging to this vty' />
+      </params>
+    </command>
+    <command id='logging filter all (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='all' doc='Do you want to log all messages?' />
+        <param name='0' doc='Only print messages matched by other filters' />
+        <param name='1' doc='Bypass filter and print all messages' />
+      </params>
+    </command>
+    <command id='logging color (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='color' doc='Configure color-printing for log messages' />
+        <param name='0' doc='Don&apos;t use color for printing messages' />
+        <param name='1' doc='Use color for printing messages' />
+      </params>
+    </command>
+    <command id='logging timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp' />
+      </params>
+    </command>
+    <command id='logging print extended-timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='extended-timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
+      </params>
+    </command>
+    <command id='logging print category (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem name' />
+      </params>
+    </command>
+    <command id='logging print category-hex (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category-hex' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem nr in hex (&apos;&lt;000b&gt;&apos;)' />
+      </params>
+    </command>
+    <command id='logging print level (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='level' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the log level name' />
+      </params>
+    </command>
+    <command id='logging print file (0|1|basename) [last]'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='file' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the source file and line' />
+        <param name='basename' doc='Prefix each log message with the source file&apos;s basename (strip leading paths) and line' />
+        <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' />
+      </params>
+    </command>
+    <command id='logging set-log-mask MASK'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='set-log-mask' doc='Set the logmask of this logging target' />
+        <param name='MASK' doc='List of logging categories to log, e.g. &apos;abc:mno:xyz&apos;. Available log categories depend on the specific application, refer to the &apos;logging level&apos; command. Optionally add individual log levels like &apos;abc,1:mno,3:xyz,5&apos;, where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' />
+      </params>
+    </command>
+    <command id='logging level (|gprs|ns|bssgp|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='gprs' doc='GPRS Packet Service' />
+        <param name='ns' doc='GPRS Network Service (NS)' />
+        <param name='bssgp' doc='GPRS BSS Gateway Protocol (BSSGP)' />
+        <param name='lglobal' doc='Library-internal global log family' />
+        <param name='llapd' doc='LAPD in libosmogsm' />
+        <param name='linp' doc='A-bis Intput Subsystem' />
+        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+        <param name='lmi' doc='A-bis Input Driver for Signalling' />
+        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+        <param name='lctrl' doc='Control Interface' />
+        <param name='lgtp' doc='GPRS GTP library' />
+        <param name='lstats' doc='Statistics messages and logging' />
+        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+        <param name='loap' doc='Osmocom Authentication Protocol' />
+        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+        <param name='ljibuf' doc='libosmo-netif Jitter Buffer' />
+        <param name='lrspro' doc='Remote SIM protocol' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level set-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level force-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the &apos;no logging level force-all&apos; command. Note: any &apos;logging level &lt;category&gt; &lt;level&gt;&apos; commands will have no visible effect after this, until the forced level is released.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='no logging level force-all'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Release any globally forced log level set with &apos;logging level force-all &lt;level&gt;&apos;' />
+      </params>
+    </command>
+    <command id='logp (|gprs|ns|bssgp|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal) .LOGMESSAGE'>
+      <params>
+        <param name='logp' doc='Print a message on all log outputs; useful for placing markers in test logs' />
+        <param name='gprs' doc='GPRS Packet Service' />
+        <param name='ns' doc='GPRS Network Service (NS)' />
+        <param name='bssgp' doc='GPRS BSS Gateway Protocol (BSSGP)' />
+        <param name='lglobal' doc='Library-internal global log family' />
+        <param name='llapd' doc='LAPD in libosmogsm' />
+        <param name='linp' doc='A-bis Intput Subsystem' />
+        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+        <param name='lmi' doc='A-bis Input Driver for Signalling' />
+        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+        <param name='lctrl' doc='Control Interface' />
+        <param name='lgtp' doc='GPRS GTP library' />
+        <param name='lstats' doc='Statistics messages and logging' />
+        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+        <param name='loap' doc='Osmocom Authentication Protocol' />
+        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+        <param name='ljibuf' doc='libosmo-netif Jitter Buffer' />
+        <param name='lrspro' doc='Remote SIM protocol' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+        <param name='.LOGMESSAGE' doc='Arbitrary message to log on given category and log level' />
+      </params>
+    </command>
+    <command id='show logging vty'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='logging' doc='Show current logging configuration' />
+        <param name='vty' doc='Show current logging configuration for this vty' />
+      </params>
+    </command>
+    <command id='show alarms'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='alarms' doc='Show current logging configuration' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH) tree ADDRESS'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+        <param name='tree' doc='Display only a specific memory chunk' />
+        <param name='ADDRESS' doc='Chunk address (e.g. 0xdeadbeef)' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH) filter REGEXP'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+        <param name='filter' doc='Filter chunks using regular expression' />
+        <param name='REGEXP' doc='Regular expression' />
+      </params>
+    </command>
+    <command id='show stats'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='stats' doc='Show statistical values' />
+      </params>
+    </command>
+    <command id='show stats level (global|peer|subscriber)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='stats' doc='Show statistical values' />
+        <param name='level' doc='Set the maximum group level' />
+        <param name='global' doc='Show global groups only' />
+        <param name='peer' doc='Show global and network peer related groups' />
+        <param name='subscriber' doc='Show global, peer, and subscriber groups' />
+      </params>
+    </command>
+    <command id='show asciidoc counters'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='asciidoc' doc='Asciidoc generation' />
+        <param name='counters' doc='Generate table of all registered counters' />
+      </params>
+    </command>
+    <command id='show rate-counters'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='rate-counters' doc='Show all rate counters' />
+      </params>
+    </command>
+    <command id='show gbproxy [stats]'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='gbproxy' doc='Display information about the Gb proxy' />
+        <param name='[stats]' doc='Show statistics' />
+      </params>
+    </command>
+    <command id='show gbproxy links'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='gbproxy' doc='Display information about the Gb proxy' />
+        <param name='links' doc='Show logical links' />
+      </params>
+    </command>
+    <command id='show ns'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='ns' doc='Display information about the NS protocol' />
+      </params>
+    </command>
+    <command id='show ns stats'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='ns' doc='Display information about the NS protocol' />
+        <param name='stats' doc='Include statistics' />
+      </params>
+    </command>
+    <command id='show ns persistent'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='ns' doc='Display information about the NS protocol' />
+        <param name='persistent' doc='Show only persistent NS' />
+      </params>
+    </command>
+    <command id='show ns (nsei|nsvc) &lt;0-65535&gt; [stats]'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='ns' doc='Display information about the NS protocol' />
+        <param name='nsei' doc='Select one NSE by its NSE Identifier' />
+        <param name='nsvc' doc='Select one NSE by its NS-VC Identifier' />
+        <param name='&lt;0-65535&gt;' doc='The Identifier of selected type' />
+        <param name='[stats]' doc='Include Statistics' />
+      </params>
+    </command>
+    <command id='logging filter nsvc (nsei|nsvci) &lt;0-65535&gt;'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='nsvc' doc='Filter based on NS Virtual Connection' />
+        <param name='nsei' doc='Identify NS-VC by NSEI' />
+        <param name='nsvci' doc='Identify NS-VC by NSVCI' />
+        <param name='&lt;0-65535&gt;' doc='Numeric identifier' />
+      </params>
+    </command>
+  </node>
+  <node id='enable'>
+    <name>enable</name>
+    <command id='disable'>
+      <params>
+        <param name='disable' doc='Turn off privileged mode command' />
+      </params>
+    </command>
+    <command id='configure terminal'>
+      <params>
+        <param name='configure' doc='Configuration from vty interface' />
+        <param name='terminal' doc='Configuration terminal' />
+      </params>
+    </command>
+    <command id='copy running-config startup-config'>
+      <params>
+        <param name='copy' doc='Copy configuration' />
+        <param name='running-config' doc='Copy running config to... ' />
+        <param name='startup-config' doc='Copy running config to startup config (same as write file)' />
+      </params>
+    </command>
+    <command id='show startup-config'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='startup-config' doc='Contentes of startup configuration' />
+      </params>
+    </command>
+    <command id='show version'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='version' doc='Displays program version' />
+      </params>
+    </command>
+    <command id='show online-help'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='online-help' doc='Online help' />
+      </params>
+    </command>
+    <command id='terminal length &lt;0-512&gt;'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='length' doc='Set number of lines on a screen' />
+        <param name='&lt;0-512&gt;' doc='Number of lines on screen (0 for no pausing)' />
+      </params>
+    </command>
+    <command id='terminal no length'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='length' doc='Set number of lines on a screen' />
+      </params>
+    </command>
+    <command id='who'>
+      <params>
+        <param name='who' doc='Display who is on vty' />
+      </params>
+    </command>
+    <command id='show history'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='history' doc='Display the session command history' />
+      </params>
+    </command>
+    <command id='terminal monitor'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='monitor' doc='Copy debug output to the current terminal line' />
+      </params>
+    </command>
+    <command id='terminal no monitor'>
+      <params>
+        <param name='terminal' doc='Set terminal line parameters' />
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='monitor' doc='Copy debug output to the current terminal line' />
+      </params>
+    </command>
+    <command id='logging enable'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='enable' doc='Enables logging to this vty' />
+      </params>
+    </command>
+    <command id='logging disable'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='disable' doc='Disables logging to this vty' />
+      </params>
+    </command>
+    <command id='logging filter all (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='all' doc='Do you want to log all messages?' />
+        <param name='0' doc='Only print messages matched by other filters' />
+        <param name='1' doc='Bypass filter and print all messages' />
+      </params>
+    </command>
+    <command id='logging color (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='color' doc='Configure color-printing for log messages' />
+        <param name='0' doc='Don&apos;t use color for printing messages' />
+        <param name='1' doc='Use color for printing messages' />
+      </params>
+    </command>
+    <command id='logging timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp' />
+      </params>
+    </command>
+    <command id='logging print extended-timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='extended-timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
+      </params>
+    </command>
+    <command id='logging print category (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem name' />
+      </params>
+    </command>
+    <command id='logging print category-hex (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category-hex' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem nr in hex (&apos;&lt;000b&gt;&apos;)' />
+      </params>
+    </command>
+    <command id='logging print level (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='level' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the log level name' />
+      </params>
+    </command>
+    <command id='logging print file (0|1|basename) [last]'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='file' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the source file and line' />
+        <param name='basename' doc='Prefix each log message with the source file&apos;s basename (strip leading paths) and line' />
+        <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' />
+      </params>
+    </command>
+    <command id='logging set-log-mask MASK'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='set-log-mask' doc='Set the logmask of this logging target' />
+        <param name='MASK' doc='List of logging categories to log, e.g. &apos;abc:mno:xyz&apos;. Available log categories depend on the specific application, refer to the &apos;logging level&apos; command. Optionally add individual log levels like &apos;abc,1:mno,3:xyz,5&apos;, where the level numbers are LOGL_DEBUG=1 LOGL_INFO=3 LOGL_NOTICE=5 LOGL_ERROR=7 LOGL_FATAL=8' />
+      </params>
+    </command>
+    <command id='logging level (|gprs|ns|bssgp|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='gprs' doc='GPRS Packet Service' />
+        <param name='ns' doc='GPRS Network Service (NS)' />
+        <param name='bssgp' doc='GPRS BSS Gateway Protocol (BSSGP)' />
+        <param name='lglobal' doc='Library-internal global log family' />
+        <param name='llapd' doc='LAPD in libosmogsm' />
+        <param name='linp' doc='A-bis Intput Subsystem' />
+        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+        <param name='lmi' doc='A-bis Input Driver for Signalling' />
+        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+        <param name='lctrl' doc='Control Interface' />
+        <param name='lgtp' doc='GPRS GTP library' />
+        <param name='lstats' doc='Statistics messages and logging' />
+        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+        <param name='loap' doc='Osmocom Authentication Protocol' />
+        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+        <param name='ljibuf' doc='libosmo-netif Jitter Buffer' />
+        <param name='lrspro' doc='Remote SIM protocol' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level set-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level force-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the &apos;no logging level force-all&apos; command. Note: any &apos;logging level &lt;category&gt; &lt;level&gt;&apos; commands will have no visible effect after this, until the forced level is released.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='no logging level force-all'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Release any globally forced log level set with &apos;logging level force-all &lt;level&gt;&apos;' />
+      </params>
+    </command>
+    <command id='logp (|gprs|ns|bssgp|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal) .LOGMESSAGE'>
+      <params>
+        <param name='logp' doc='Print a message on all log outputs; useful for placing markers in test logs' />
+        <param name='gprs' doc='GPRS Packet Service' />
+        <param name='ns' doc='GPRS Network Service (NS)' />
+        <param name='bssgp' doc='GPRS BSS Gateway Protocol (BSSGP)' />
+        <param name='lglobal' doc='Library-internal global log family' />
+        <param name='llapd' doc='LAPD in libosmogsm' />
+        <param name='linp' doc='A-bis Intput Subsystem' />
+        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+        <param name='lmi' doc='A-bis Input Driver for Signalling' />
+        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+        <param name='lctrl' doc='Control Interface' />
+        <param name='lgtp' doc='GPRS GTP library' />
+        <param name='lstats' doc='Statistics messages and logging' />
+        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+        <param name='loap' doc='Osmocom Authentication Protocol' />
+        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+        <param name='ljibuf' doc='libosmo-netif Jitter Buffer' />
+        <param name='lrspro' doc='Remote SIM protocol' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+        <param name='.LOGMESSAGE' doc='Arbitrary message to log on given category and log level' />
+      </params>
+    </command>
+    <command id='show logging vty'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='logging' doc='Show current logging configuration' />
+        <param name='vty' doc='Show current logging configuration for this vty' />
+      </params>
+    </command>
+    <command id='show alarms'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='alarms' doc='Show current logging configuration' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH) tree ADDRESS'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+        <param name='tree' doc='Display only a specific memory chunk' />
+        <param name='ADDRESS' doc='Chunk address (e.g. 0xdeadbeef)' />
+      </params>
+    </command>
+    <command id='show talloc-context (application|all) (full|brief|DEPTH) filter REGEXP'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='talloc-context' doc='Show talloc memory hierarchy' />
+        <param name='application' doc='Application&apos;s context' />
+        <param name='all' doc='All contexts, if NULL-context tracking is enabled' />
+        <param name='full' doc='Display a full talloc memory hierarchy' />
+        <param name='brief' doc='Display a brief talloc memory hierarchy' />
+        <param name='DEPTH' doc='Specify required maximal depth value' />
+        <param name='filter' doc='Filter chunks using regular expression' />
+        <param name='REGEXP' doc='Regular expression' />
+      </params>
+    </command>
+    <command id='show stats'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='stats' doc='Show statistical values' />
+      </params>
+    </command>
+    <command id='show stats level (global|peer|subscriber)'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='stats' doc='Show statistical values' />
+        <param name='level' doc='Set the maximum group level' />
+        <param name='global' doc='Show global groups only' />
+        <param name='peer' doc='Show global and network peer related groups' />
+        <param name='subscriber' doc='Show global, peer, and subscriber groups' />
+      </params>
+    </command>
+    <command id='show asciidoc counters'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='asciidoc' doc='Asciidoc generation' />
+        <param name='counters' doc='Generate table of all registered counters' />
+      </params>
+    </command>
+    <command id='show rate-counters'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='rate-counters' doc='Show all rate counters' />
+      </params>
+    </command>
+    <command id='show gbproxy [stats]'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='gbproxy' doc='Display information about the Gb proxy' />
+        <param name='[stats]' doc='Show statistics' />
+      </params>
+    </command>
+    <command id='show gbproxy links'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='gbproxy' doc='Display information about the Gb proxy' />
+        <param name='links' doc='Show logical links' />
+      </params>
+    </command>
+    <command id='delete-gbproxy-peer &lt;0-65534&gt; bvci &lt;2-65534&gt;'>
+      <params>
+        <param name='delete-gbproxy-peer' doc='Delete a GBProxy peer by NSEI and optionally BVCI' />
+        <param name='&lt;0-65534&gt;' doc='NSEI number' />
+        <param name='bvci' doc='Only delete peer with a matching BVCI' />
+        <param name='&lt;2-65534&gt;' doc='BVCI number' />
+      </params>
+    </command>
+    <command id='delete-gbproxy-peer &lt;0-65534&gt; (only-bvc|only-nsvc|all) [dry-run]'>
+      <params>
+        <param name='delete-gbproxy-peer' doc='Delete a GBProxy peer by NSEI and optionally BVCI' />
+        <param name='&lt;0-65534&gt;' doc='NSEI number' />
+        <param name='only-bvc' doc='Only delete BSSGP connections (BVC)' />
+        <param name='only-nsvc' doc='Only delete dynamic NS connections (NS-VC)' />
+        <param name='all' doc='Delete BVC and dynamic NS connections' />
+        <param name='[dry-run]' doc='Show what would be deleted instead of actually deleting' />
+      </params>
+    </command>
+    <command id='delete-gbproxy-link &lt;0-65534&gt; (tlli|imsi|sgsn-nsei) IDENT'>
+      <params>
+        <param name='delete-gbproxy-link' doc='Delete a GBProxy logical link entry by NSEI and identification' />
+        <param name='&lt;0-65534&gt;' doc='NSEI number' />
+        <param name='tlli' doc='Delete entries with a matching TLLI (hex)' />
+        <param name='imsi' doc='Delete entries with a matching IMSI' />
+        <param name='sgsn-nsei' doc='Delete entries with a matching SGSN NSEI' />
+        <param name='IDENT' doc='Identification to match' />
+      </params>
+    </command>
+    <command id='delete-gbproxy-link &lt;0-65534&gt; (stale|de-registered)'>
+      <params>
+        <param name='delete-gbproxy-link' doc='Delete a GBProxy logical link entry by NSEI and identification' />
+        <param name='&lt;0-65534&gt;' doc='NSEI number' />
+        <param name='stale' doc='Delete stale entries' />
+        <param name='de-registered' doc='Delete de-registered entries' />
+      </params>
+    </command>
+    <command id='show ns'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='ns' doc='Display information about the NS protocol' />
+      </params>
+    </command>
+    <command id='show ns stats'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='ns' doc='Display information about the NS protocol' />
+        <param name='stats' doc='Include statistics' />
+      </params>
+    </command>
+    <command id='show ns persistent'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='ns' doc='Display information about the NS protocol' />
+        <param name='persistent' doc='Show only persistent NS' />
+      </params>
+    </command>
+    <command id='show ns (nsei|nsvc) &lt;0-65535&gt; [stats]'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='ns' doc='Display information about the NS protocol' />
+        <param name='nsei' doc='Select one NSE by its NSE Identifier' />
+        <param name='nsvc' doc='Select one NSE by its NS-VC Identifier' />
+        <param name='&lt;0-65535&gt;' doc='The Identifier of selected type' />
+        <param name='[stats]' doc='Include Statistics' />
+      </params>
+    </command>
+    <command id='logging filter nsvc (nsei|nsvci) &lt;0-65535&gt;'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='nsvc' doc='Filter based on NS Virtual Connection' />
+        <param name='nsei' doc='Identify NS-VC by NSEI' />
+        <param name='nsvci' doc='Identify NS-VC by NSVCI' />
+        <param name='&lt;0-65535&gt;' doc='Numeric identifier' />
+      </params>
+    </command>
+    <command id='nsvc (nsei|nsvci) &lt;0-65535&gt; (block|unblock|reset)'>
+      <params>
+        <param name='nsvc' doc='Perform an operation on a NSVC' />
+        <param name='nsei' doc='NSEI to identify NS-VC Identifier (NS-VCI)' />
+        <param name='nsvci' doc='NS-VC Identifier (NS-VCI)' />
+        <param name='&lt;0-65535&gt;' doc='The NSEI' />
+        <param name='block' doc='Initiate BLOCK procedure' />
+        <param name='unblock' doc='Initiate UNBLOCK procedure' />
+        <param name='reset' doc='Initiate RESET procedure' />
+      </params>
+    </command>
+  </node>
+  <node id='config'>
+    <name>config</name>
+    <command id='hostname WORD'>
+      <params>
+        <param name='hostname' doc='Set system&apos;s network name' />
+        <param name='WORD' doc='This system&apos;s network name' />
+      </params>
+    </command>
+    <command id='no hostname [HOSTNAME]'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='hostname' doc='Reset system&apos;s network name' />
+        <param name='[HOSTNAME]' doc='Host name of this router' />
+      </params>
+    </command>
+    <command id='password (8|) WORD'>
+      <params>
+        <param name='password' doc='Assign the terminal connection password' />
+        <param name='8' doc='Specifies a HIDDEN password will follow' />
+        <param name='' doc='dummy string ' />
+        <param name='WORD' doc='The HIDDEN line password string' />
+      </params>
+    </command>
+    <command id='password LINE'>
+      <params>
+        <param name='password' doc='Assign the terminal connection password' />
+        <param name='LINE' doc='The UNENCRYPTED (cleartext) line password' />
+      </params>
+    </command>
+    <command id='enable password (8|) WORD'>
+      <params>
+        <param name='enable' doc='Modify enable password parameters' />
+        <param name='password' doc='Assign the privileged level password' />
+        <param name='8' doc='Specifies a HIDDEN password will follow' />
+        <param name='' doc='dummy string ' />
+        <param name='WORD' doc='The HIDDEN &apos;enable&apos; password string' />
+      </params>
+    </command>
+    <command id='enable password LINE'>
+      <params>
+        <param name='enable' doc='Modify enable password parameters' />
+        <param name='password' doc='Assign the privileged level password' />
+        <param name='LINE' doc='The UNENCRYPTED (cleartext) &apos;enable&apos; password' />
+      </params>
+    </command>
+    <command id='no enable password'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='enable' doc='Modify enable password parameters' />
+        <param name='password' doc='Assign the privileged level password' />
+      </params>
+    </command>
+    <command id='banner motd default'>
+      <params>
+        <param name='banner' doc='Set banner string' />
+        <param name='motd' doc='Strings for motd' />
+        <param name='default' doc='Default string' />
+      </params>
+    </command>
+    <command id='banner motd file [FILE]'>
+      <params>
+        <param name='banner' doc='Set banner' />
+        <param name='motd' doc='Banner for motd' />
+        <param name='file' doc='Banner from a file' />
+        <param name='[FILE]' doc='Filename' />
+      </params>
+    </command>
+    <command id='no banner motd'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='banner' doc='Set banner string' />
+        <param name='motd' doc='Strings for motd' />
+      </params>
+    </command>
+    <command id='service terminal-length &lt;0-512&gt;'>
+      <params>
+        <param name='service' doc='Set up miscellaneous service' />
+        <param name='terminal-length' doc='System wide terminal length configuration' />
+        <param name='&lt;0-512&gt;' doc='Number of lines of VTY (0 means no line control)' />
+      </params>
+    </command>
+    <command id='no service terminal-length [&lt;0-512&gt;]'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='service' doc='Set up miscellaneous service' />
+        <param name='terminal-length' doc='System wide terminal length configuration' />
+        <param name='[&lt;0-512&gt;]' doc='Number of lines of VTY (0 means no line control)' />
+      </params>
+    </command>
+    <command id='line vty'>
+      <params>
+        <param name='line' doc='Configure a terminal line' />
+        <param name='vty' doc='Virtual terminal' />
+      </params>
+    </command>
+    <command id='service advanced-vty'>
+      <params>
+        <param name='service' doc='Set up miscellaneous service' />
+        <param name='advanced-vty' doc='Enable advanced mode vty interface' />
+      </params>
+    </command>
+    <command id='no service advanced-vty'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='service' doc='Set up miscellaneous service' />
+        <param name='advanced-vty' doc='Enable advanced mode vty interface' />
+      </params>
+    </command>
+    <command id='show history'>
+      <params>
+        <param name='show' doc='Show running system information' />
+        <param name='history' doc='Display the session command history' />
+      </params>
+    </command>
+    <command id='log stderr'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='stderr' doc='Logging via STDERR of the process' />
+      </params>
+    </command>
+    <command id='no log stderr'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='stderr' doc='Logging via STDERR of the process' />
+      </params>
+    </command>
+    <command id='log file .FILENAME'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='file' doc='Logging to text file' />
+        <param name='.FILENAME' doc='Filename' />
+      </params>
+    </command>
+    <command id='no log file .FILENAME'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='file' doc='Logging to text file' />
+        <param name='.FILENAME' doc='Filename' />
+      </params>
+    </command>
+    <command id='log alarms &lt;2-32700&gt;'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='alarms' doc='Logging alarms to osmo_strrb' />
+        <param name='&lt;2-32700&gt;' doc='Maximum number of messages to log' />
+      </params>
+    </command>
+    <command id='no log alarms'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='alarms' doc='Logging alarms to osmo_strrb' />
+      </params>
+    </command>
+    <command id='log syslog (authpriv|cron|daemon|ftp|lpr|mail|news|user|uucp)'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='syslog' doc='Logging via syslog' />
+        <param name='authpriv' doc='Security/authorization messages facility' />
+        <param name='cron' doc='Clock daemon (cron/at) facility' />
+        <param name='daemon' doc='General system daemon facility' />
+        <param name='ftp' doc='Ftp daemon facility' />
+        <param name='lpr' doc='Line printer facility' />
+        <param name='mail' doc='Mail facility' />
+        <param name='news' doc='News facility' />
+        <param name='user' doc='Generic facility' />
+        <param name='uucp' doc='UUCP facility' />
+      </params>
+    </command>
+    <command id='log syslog local &lt;0-7&gt;'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='syslog' doc='Logging via syslog' />
+        <param name='local' doc='Syslog LOCAL facility' />
+        <param name='&lt;0-7&gt;' doc='Local facility number' />
+      </params>
+    </command>
+    <command id='no log syslog'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='syslog' doc='Logging via syslog' />
+      </params>
+    </command>
+    <command id='log gsmtap [HOSTNAME]'>
+      <params>
+        <param name='log' doc='Configure logging sub-system' />
+        <param name='gsmtap' doc='Logging via GSMTAP' />
+        <param name='[HOSTNAME]' doc='Host name to send the GSMTAP logging to (UDP port 4729)' />
+      </params>
+    </command>
+    <command id='stats reporter statsd'>
+      <params>
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='reporter' doc='Configure a stats reporter' />
+        <param name='statsd' doc='Report to a STATSD server' />
+      </params>
+    </command>
+    <command id='no stats reporter statsd'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='reporter' doc='Configure a stats reporter' />
+        <param name='statsd' doc='Report to a STATSD server' />
+      </params>
+    </command>
+    <command id='stats reporter log'>
+      <params>
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='reporter' doc='Configure a stats reporter' />
+        <param name='log' doc='Report to the logger' />
+      </params>
+    </command>
+    <command id='no stats reporter log'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='reporter' doc='Configure a stats reporter' />
+        <param name='log' doc='Report to the logger' />
+      </params>
+    </command>
+    <command id='stats interval &lt;1-65535&gt;'>
+      <params>
+        <param name='stats' doc='Configure stats sub-system' />
+        <param name='interval' doc='Set the reporting interval' />
+        <param name='&lt;1-65535&gt;' doc='Interval in seconds' />
+      </params>
+    </command>
+    <command id='gbproxy'>
+      <params>
+        <param name='gbproxy' doc='Configure the Gb proxy' />
+      </params>
+    </command>
+    <command id='ns'>
+      <params>
+        <param name='ns' doc='Configure the GPRS Network Service' />
+      </params>
+    </command>
+  </node>
+  <node id='config-log'>
+    <name>config-log</name>
+    <command id='logging filter all (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='all' doc='Do you want to log all messages?' />
+        <param name='0' doc='Only print messages matched by other filters' />
+        <param name='1' doc='Bypass filter and print all messages' />
+      </params>
+    </command>
+    <command id='logging color (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='color' doc='Configure color-printing for log messages' />
+        <param name='0' doc='Don&apos;t use color for printing messages' />
+        <param name='1' doc='Use color for printing messages' />
+      </params>
+    </command>
+    <command id='logging timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp' />
+      </params>
+    </command>
+    <command id='logging print extended-timestamp (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='extended-timestamp' doc='Configure log message timestamping' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with current timestamp with YYYYMMDDhhmmssnnn' />
+      </params>
+    </command>
+    <command id='logging print category (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem name' />
+      </params>
+    </command>
+    <command id='logging print category-hex (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='category-hex' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with category/subsystem nr in hex (&apos;&lt;000b&gt;&apos;)' />
+      </params>
+    </command>
+    <command id='logging print level (0|1)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='level' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the log level name' />
+      </params>
+    </command>
+    <command id='logging print file (0|1|basename) [last]'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='print' doc='Log output settings' />
+        <param name='file' doc='Configure log message' />
+        <param name='0' doc='Don&apos;t prefix each log message' />
+        <param name='1' doc='Prefix each log message with the source file and line' />
+        <param name='basename' doc='Prefix each log message with the source file&apos;s basename (strip leading paths) and line' />
+        <param name='[last]' doc='Log source file info at the end of a log line. If omitted, log source file info just before the log text.' />
+      </params>
+    </command>
+    <command id='logging level (|gprs|ns|bssgp|lglobal|llapd|linp|lmux|lmi|lmib|lsms|lctrl|lgtp|lstats|lgsup|loap|lss7|lsccp|lsua|lm3ua|lmgcp|ljibuf|lrspro) (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='gprs' doc='GPRS Packet Service' />
+        <param name='ns' doc='GPRS Network Service (NS)' />
+        <param name='bssgp' doc='GPRS BSS Gateway Protocol (BSSGP)' />
+        <param name='lglobal' doc='Library-internal global log family' />
+        <param name='llapd' doc='LAPD in libosmogsm' />
+        <param name='linp' doc='A-bis Intput Subsystem' />
+        <param name='lmux' doc='A-bis B-Subchannel TRAU Frame Multiplex' />
+        <param name='lmi' doc='A-bis Input Driver for Signalling' />
+        <param name='lmib' doc='A-bis Input Driver for B-Channels (voice)' />
+        <param name='lsms' doc='Layer3 Short Message Service (SMS)' />
+        <param name='lctrl' doc='Control Interface' />
+        <param name='lgtp' doc='GPRS GTP library' />
+        <param name='lstats' doc='Statistics messages and logging' />
+        <param name='lgsup' doc='Generic Subscriber Update Protocol' />
+        <param name='loap' doc='Osmocom Authentication Protocol' />
+        <param name='lss7' doc='libosmo-sigtran Signalling System 7' />
+        <param name='lsccp' doc='libosmo-sigtran SCCP Implementation' />
+        <param name='lsua' doc='libosmo-sigtran SCCP User Adaptation' />
+        <param name='lm3ua' doc='libosmo-sigtran MTP3 User Adaptation' />
+        <param name='lmgcp' doc='libosmo-mgcp Media Gateway Control Protocol' />
+        <param name='ljibuf' doc='libosmo-netif Jitter Buffer' />
+        <param name='lrspro' doc='Remote SIM protocol' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level set-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='set-all' doc='Once-off set all categories to the given log level. There is no single command to take back these changes -- each category is set to the given level, period.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='logging level force-all (debug|info|notice|error|fatal)'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Globally force all logging categories to a specific level. This is released by the &apos;no logging level force-all&apos; command. Note: any &apos;logging level &lt;category&gt; &lt;level&gt;&apos; commands will have no visible effect after this, until the forced level is released.' />
+        <param name='debug' doc='Log debug messages and higher levels' />
+        <param name='info' doc='Log informational messages and higher levels' />
+        <param name='notice' doc='Log noticeable messages and higher levels' />
+        <param name='error' doc='Log error messages and higher levels' />
+        <param name='fatal' doc='Log only fatal messages' />
+      </params>
+    </command>
+    <command id='no logging level force-all'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='logging' doc='Configure logging' />
+        <param name='level' doc='Set the log level for a specified category' />
+        <param name='force-all' doc='Release any globally forced log level set with &apos;logging level force-all &lt;level&gt;&apos;' />
+      </params>
+    </command>
+    <command id='logging filter nsvc (nsei|nsvci) &lt;0-65535&gt;'>
+      <params>
+        <param name='logging' doc='Configure logging' />
+        <param name='filter' doc='Filter log messages' />
+        <param name='nsvc' doc='Filter based on NS Virtual Connection' />
+        <param name='nsei' doc='Identify NS-VC by NSEI' />
+        <param name='nsvci' doc='Identify NS-VC by NSVCI' />
+        <param name='&lt;0-65535&gt;' doc='Numeric identifier' />
+      </params>
+    </command>
+  </node>
+  <node id='config-stats'>
+    <name>config-stats</name>
+    <command id='local-ip ADDR'>
+      <params>
+        <param name='local-ip' doc='Set the IP address to which we bind locally' />
+        <param name='ADDR' doc='IP Address' />
+      </params>
+    </command>
+    <command id='no local-ip'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='local-ip' doc='Set the IP address to which we bind locally' />
+      </params>
+    </command>
+    <command id='remote-ip ADDR'>
+      <params>
+        <param name='remote-ip' doc='Set the remote IP address to which we connect' />
+        <param name='ADDR' doc='IP Address' />
+      </params>
+    </command>
+    <command id='remote-port &lt;1-65535&gt;'>
+      <params>
+        <param name='remote-port' doc='Set the remote port to which we connect' />
+        <param name='&lt;1-65535&gt;' doc='Remote port number' />
+      </params>
+    </command>
+    <command id='mtu &lt;100-65535&gt;'>
+      <params>
+        <param name='mtu' doc='Set the maximum packet size' />
+        <param name='&lt;100-65535&gt;' doc='Size in byte' />
+      </params>
+    </command>
+    <command id='no mtu'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='mtu' doc='Set the maximum packet size' />
+      </params>
+    </command>
+    <command id='prefix PREFIX'>
+      <params>
+        <param name='prefix' doc='Set the item name prefix' />
+        <param name='PREFIX' doc='The prefix string' />
+      </params>
+    </command>
+    <command id='no prefix'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='prefix' doc='Set the item name prefix' />
+      </params>
+    </command>
+    <command id='level (global|peer|subscriber)'>
+      <params>
+        <param name='level' doc='Set the maximum group level' />
+        <param name='global' doc='Report global groups only' />
+        <param name='peer' doc='Report global and network peer related groups' />
+        <param name='subscriber' doc='Report global, peer, and subscriber groups' />
+      </params>
+    </command>
+    <command id='enable'>
+      <params>
+        <param name='enable' doc='Enable the reporter' />
+      </params>
+    </command>
+    <command id='disable'>
+      <params>
+        <param name='disable' doc='Disable the reporter' />
+      </params>
+    </command>
+  </node>
+  <node id='config-line'>
+    <name>config-line</name>
+    <command id='login'>
+      <params>
+        <param name='login' doc='Enable password checking' />
+      </params>
+    </command>
+    <command id='no login'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='login' doc='Enable password checking' />
+      </params>
+    </command>
+    <command id='bind A.B.C.D [&lt;0-65535&gt;]'>
+      <params>
+        <param name='bind' doc='Accept VTY telnet connections on local interface' />
+        <param name='A.B.C.D' doc='Local interface IP address (default: 127.0.0.1)' />
+        <param name='[&lt;0-65535&gt;]' doc='Local TCP port number' />
+      </params>
+    </command>
+  </node>
+  <node id='config-ns'>
+    <name>config-ns</name>
+    <command id='nse &lt;0-65535&gt; nsvci &lt;0-65534&gt;'>
+      <params>
+        <param name='nse' doc='Persistent NS Entity' />
+        <param name='&lt;0-65535&gt;' doc='NS Entity ID (NSEI)' />
+        <param name='nsvci' doc='NS Virtual Connection' />
+        <param name='&lt;0-65534&gt;' doc='NS Virtual Connection ID (NSVCI)' />
+      </params>
+    </command>
+    <command id='nse &lt;0-65535&gt; remote-ip A.B.C.D'>
+      <params>
+        <param name='nse' doc='Persistent NS Entity' />
+        <param name='&lt;0-65535&gt;' doc='NS Entity ID (NSEI)' />
+        <param name='remote-ip' doc='Remote IP Address' />
+        <param name='A.B.C.D' doc='Remote IP Address' />
+      </params>
+    </command>
+    <command id='nse &lt;0-65535&gt; remote-port &lt;0-65535&gt;'>
+      <params>
+        <param name='nse' doc='Persistent NS Entity' />
+        <param name='&lt;0-65535&gt;' doc='NS Entity ID (NSEI)' />
+        <param name='remote-port' doc='Remote UDP Port' />
+        <param name='&lt;0-65535&gt;' doc='Remote UDP Port Number' />
+      </params>
+    </command>
+    <command id='nse &lt;0-65535&gt; fr-dlci &lt;16-1007&gt;'>
+      <params>
+        <param name='nse' doc='Persistent NS Entity' />
+        <param name='&lt;0-65535&gt;' doc='NS Entity ID (NSEI)' />
+        <param name='fr-dlci' doc='Frame Relay DLCI' />
+        <param name='&lt;16-1007&gt;' doc='Frame Relay DLCI Number' />
+      </params>
+    </command>
+    <command id='nse &lt;0-65535&gt; encapsulation (udp|framerelay-gre)'>
+      <params>
+        <param name='nse' doc='Persistent NS Entity' />
+        <param name='&lt;0-65535&gt;' doc='NS Entity ID (NSEI)' />
+        <param name='encapsulation' doc='Encapsulation for NS' />
+        <param name='udp' doc='UDP/IP Encapsulation' />
+        <param name='framerelay-gre' doc='Frame-Relay/GRE/IP Encapsulation' />
+      </params>
+    </command>
+    <command id='nse &lt;0-65535&gt; remote-role (sgsn|bss)'>
+      <params>
+        <param name='nse' doc='Persistent NS Entity' />
+        <param name='&lt;0-65535&gt;' doc='NS Entity ID (NSEI)' />
+        <param name='remote-role' doc='Remote NSE Role' />
+        <param name='sgsn' doc='Remote Peer is SGSN' />
+        <param name='bss' doc='Remote Peer is BSS' />
+      </params>
+    </command>
+    <command id='no nse &lt;0-65535&gt;'>
+      <params>
+        <param name='no' doc='Delete Persistent NS Entity' />
+        <param name='nse' doc='Delete Persistent NS Entity' />
+        <param name='&lt;0-65535&gt;' doc='NS Entity ID (NSEI)' />
+      </params>
+    </command>
+    <command id='timer (tns-block|tns-block-retries|tns-reset|tns-reset-retries|tns-test|tns-alive|tns-alive-retries|tsns-prov) &lt;0-65535&gt;'>
+      <params>
+        <param name='timer' doc='Network Service Timer' />
+        <param name='tns-block' doc='(un)blocking Timer (Tns-block) timeout' />
+        <param name='tns-block-retries' doc='(un)blocking Timer (Tns-block) number of retries' />
+        <param name='tns-reset' doc='Reset Timer (Tns-reset) timeout' />
+        <param name='tns-reset-retries' doc='Reset Timer (Tns-reset) number of retries' />
+        <param name='tns-test' doc='Test Timer (Tns-test) timeout' />
+        <param name='tns-alive' doc='Alive Timer (Tns-alive) timeout' />
+        <param name='tns-alive-retries' doc='Alive Timer (Tns-alive) number of retries' />
+        <param name='tsns-prov' doc='SNS Provision Timer (Tsns-prov) timeout' />
+        <param name='&lt;0-65535&gt;' doc='Timer Value' />
+      </params>
+    </command>
+    <command id='encapsulation udp local-ip A.B.C.D'>
+      <params>
+        <param name='encapsulation' doc='NS encapsulation options' />
+        <param name='udp' doc='NS over UDP Encapsulation' />
+        <param name='local-ip' doc='Set the IP address on which we listen for NS/UDP' />
+        <param name='A.B.C.D' doc='IP Address' />
+      </params>
+    </command>
+    <command id='encapsulation udp local-port &lt;0-65535&gt;'>
+      <params>
+        <param name='encapsulation' doc='NS encapsulation options' />
+        <param name='udp' doc='NS over UDP Encapsulation' />
+        <param name='local-port' doc='Set the UDP port on which we listen for NS/UDP' />
+        <param name='&lt;0-65535&gt;' doc='UDP port number' />
+      </params>
+    </command>
+    <command id='encapsulation udp dscp &lt;0-255&gt;'>
+      <params>
+        <param name='encapsulation' doc='NS encapsulation options' />
+        <param name='udp' doc='NS over UDP Encapsulation' />
+        <param name='dscp' doc='Set DSCP/TOS on the UDP socket' />
+        <param name='&lt;0-255&gt;' doc='DSCP Value' />
+      </params>
+    </command>
+    <command id='encapsulation framerelay-gre enabled (1|0)'>
+      <params>
+        <param name='encapsulation' doc='NS encapsulation options' />
+        <param name='framerelay-gre' doc='NS over Frame Relay over GRE Encapsulation' />
+        <param name='enabled' doc='Enable or disable Frame Relay over GRE' />
+        <param name='1' doc='Enable' />
+        <param name='0' doc='Disable' />
+      </params>
+    </command>
+    <command id='encapsulation framerelay-gre local-ip A.B.C.D'>
+      <params>
+        <param name='encapsulation' doc='NS encapsulation options' />
+        <param name='framerelay-gre' doc='NS over Frame Relay over GRE Encapsulation' />
+        <param name='local-ip' doc='Set the IP address on which we listen for NS/FR/GRE' />
+        <param name='A.B.C.D' doc='IP Address' />
+      </params>
+    </command>
+  </node>
+  <node id='config-gbproxy'>
+    <name>config-gbproxy</name>
+    <command id='sgsn nsei &lt;0-65534&gt;'>
+      <params>
+        <param name='sgsn' doc='SGSN information' />
+        <param name='nsei' doc='NSEI to be used in the connection with the SGSN' />
+        <param name='&lt;0-65534&gt;' doc='The NSEI' />
+      </params>
+    </command>
+    <command id='core-mobile-country-code &lt;1-999&gt;'>
+      <params>
+        <param name='core-mobile-country-code' doc='Use this country code for the core network' />
+        <param name='&lt;1-999&gt;' doc='MCC value' />
+      </params>
+    </command>
+    <command id='core-mobile-network-code &lt;1-999&gt;'>
+      <params>
+        <param name='core-mobile-network-code' doc='Use this network code for the core network' />
+        <param name='&lt;1-999&gt;' doc='NCC value' />
+      </params>
+    </command>
+    <command id='match-imsi (patching|routing) .REGEXP'>
+      <params>
+        <param name='match-imsi' doc='Restrict actions to certain IMSIs' />
+        <param name='patching' doc='Patch MS related information elements on match only' />
+        <param name='routing' doc='Route to the secondary SGSN on match only' />
+        <param name='.REGEXP' doc='Regular expression for the IMSI match' />
+      </params>
+    </command>
+    <command id='core-access-point-name (APN|none)'>
+      <params>
+        <param name='core-access-point-name' doc='Use this access point name (APN) for the backbone' />
+        <param name='APN' doc='Replace APN by this string' />
+        <param name='none' doc='Remove APN' />
+      </params>
+    </command>
+    <command id='secondary-sgsn nsei &lt;0-65534&gt;'>
+      <params>
+        <param name='secondary-sgsn' doc='Route matching LLC connections to a second SGSN (Experimental)' />
+        <param name='nsei' doc='NSEI to be used in the connection with the SGSN' />
+        <param name='&lt;0-65534&gt;' doc='The NSEI' />
+      </params>
+    </command>
+    <command id='patch-ptmsi'>
+      <params>
+        <param name='patch-ptmsi' doc='Patch P-TMSI/TLLI' />
+      </params>
+    </command>
+    <command id='acquire-imsi'>
+      <params>
+        <param name='acquire-imsi' doc='Acquire the IMSI before establishing a LLC connection (Experimental)' />
+      </params>
+    </command>
+    <command id='link-list clean-stale-timer &lt;1-999999&gt;'>
+      <params>
+        <param name='link-list' doc='Set TLLI list parameters' />
+        <param name='clean-stale-timer' doc='Periodic timer to clean stale links' />
+        <param name='&lt;1-999999&gt;' doc='Frequency at which the periodic timer is fired (in seconds)' />
+      </params>
+    </command>
+    <command id='link-list max-age &lt;1-999999&gt;'>
+      <params>
+        <param name='link-list' doc='Set TLLI list parameters' />
+        <param name='max-age' doc='Limit maximum age' />
+        <param name='&lt;1-999999&gt;' doc='Maximum age in seconds' />
+      </params>
+    </command>
+    <command id='link-list max-length &lt;1-99999&gt;'>
+      <params>
+        <param name='link-list' doc='Set TLLI list parameters' />
+        <param name='max-length' doc='Limit list length' />
+        <param name='&lt;1-99999&gt;' doc='Maximum number of logical links in the list' />
+      </params>
+    </command>
+    <command id='link-list keep-mode (never|re-attach|identified|always)'>
+      <params>
+        <param name='link-list' doc='Set TLLI list parameters' />
+        <param name='keep-mode' doc='How to keep entries for detached logical links' />
+        <param name='never' doc='Discard entry immediately after detachment' />
+        <param name='re-attach' doc='Keep entry if a re-attachment has be requested' />
+        <param name='identified' doc='Keep entry if it associated with an IMSI' />
+        <param name='always' doc='Don&apos;t discard entries after detachment' />
+      </params>
+    </command>
+    <command id='link stored-msgs-max-length &lt;1-99999&gt;'>
+      <params>
+        <param name='link' doc='Set TLLI parameters' />
+        <param name='stored-msgs-max-length' doc='Limit list length' />
+        <param name='&lt;1-99999&gt;' doc='Maximum number of msgb stored in the logical link waiting to acquire its IMSI' />
+      </params>
+    </command>
+    <command id='no core-mobile-country-code'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='core-mobile-country-code' doc='Use this country code for the core network' />
+      </params>
+    </command>
+    <command id='no core-mobile-network-code'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='core-mobile-network-code' doc='Use this network code for the core network' />
+      </params>
+    </command>
+    <command id='no match-imsi'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='match-imsi' doc='Restrict actions to certain IMSIs' />
+      </params>
+    </command>
+    <command id='no core-access-point-name'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='core-access-point-name' doc='Use this access point name (APN) for the backbone' />
+      </params>
+    </command>
+    <command id='no secondary-sgsn'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='secondary-sgsn' doc='Route matching LLC connections to a second SGSN (Experimental)' />
+      </params>
+    </command>
+    <command id='no patch-ptmsi'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='patch-ptmsi' doc='Patch P-TMSI/TLLI' />
+      </params>
+    </command>
+    <command id='no acquire-imsi'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='acquire-imsi' doc='Acquire the IMSI before establishing a LLC connection (Experimental)' />
+      </params>
+    </command>
+    <command id='no link-list clean-stale-timer'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='link-list' doc='Set TLLI list parameters' />
+        <param name='clean-stale-timer' doc='Periodic timer to clean stale links' />
+      </params>
+    </command>
+    <command id='no link-list max-age'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='link-list' doc='Set TLLI list parameters' />
+        <param name='max-age' doc='Limit maximum age' />
+      </params>
+    </command>
+    <command id='no link-list max-length'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='link-list' doc='Set TLLI list parameters' />
+        <param name='max-length' doc='Limit list length' />
+      </params>
+    </command>
+    <command id='no link stored-msgs-max-length'>
+      <params>
+        <param name='no' doc='Negate a command or set its defaults' />
+        <param name='link' doc='Set TLLI parameters' />
+        <param name='stored-msgs-max-length' doc='Limit list length' />
+      </params>
+    </command>
+  </node>
+</vtydoc>