create an initial tag for the firmware version

1. d373558 src: Add .gitignore for the software by Sylvain Munaut · 6 years ago
2. 2c3c275 osmo_e1f: Fix Makefile to use pkg-config by Sylvain Munaut · 6 years ago
3. a3ddfb1 Merge branch 'laforge/software' by Harald Welte · 6 years ago
4. 24531ce rename osmo_e1 to osmo_e1f ("f" for "framer") by Harald Welte · 6 years ago
5. 82fb9b7 osmo_e1: fix make clean by Harald Welte · 6 years ago
6. cdbcff9 CRC4: use proper CRC4 table to avoid bit-reversal of each byte by Harald Welte · 6 years ago
7. ce18a04 add e1_test_dieter to deframe/decode dieters capture by Harald Welte · 6 years ago
8. 8a95fd5 osmo_e1: Add HDLC framing/deframing by Harald Welte · 6 years ago
9. 37e2374 osmo_e1: Silence the FSM logging by Harald Welte · 6 years ago
10. 9bd2c9f HACK to make CRC4 computation work by Harald Welte · 6 years ago
11. d3941c6 osmo_e1.c: Fix handling of TS2..31 (use 'i', not '1') by Harald Welte · 6 years ago
12. f01471d add some information related a SAM4S based USB-to-LIU adapter board idea by Harald Welte · 6 years ago
13. 0c756eb WIP: Software for E1 mux/demux by Harald Welte · 6 years ago
14. 5b15f68 add E1 tap hardware design by Harald Welte · 12 years ago
15. ceb6ef1 laforge.lbr: fix amphenol sim reader footprint by Harald Welte · 12 years ago
16. b59bfbc major update of laforge.lbr with lots of new components by Harald Welte · 12 years ago
17. 605e3e4 add some glue code between the idt82 driver and at91lib SPI by Harald Welte · 12 years ago
18. 638afbb 'new' PCB routing by Christian Vogel by Harald Welte · 12 years ago
19. 28460ee major update of laforge.lbr with lots of new components by Harald Welte · 12 years ago
20. da02f55 add initial driver skeleton for idt82v2081 chip by Harald Welte · 12 years ago
21. ceb70a8 give parts names without "$", use 47nH as L1 (1206) by Harald Welte · 12 years ago
22. b8dfc48 approve lots of warnings about thinner wires by Harald Welte · 13 years ago
23. 71ba939 remove stray GNDIO wire, add junction, approve some warnings by Harald Welte · 13 years ago
24. 5becd7e re-route complete board, add PWR jumper, LED series resistor by Christian Vogel · 13 years ago
25. a40a482 add partlist/bom by Harald Welte · 13 years ago
26. 372a183 update schematics and PCB layout by Harald Welte · 13 years ago
27. 07c856a re-route pcb with LEDs by Harald Welte · 13 years ago
28. f687f38 add two LEDs (power and LOS) plus required transistor by Harald Welte · 13 years ago
29. a2c23eb re-route the entire board to add test pads and additional components by Harald Welte · 13 years ago
30. 8b0e886 just name some signals/networks by Harald Welte · 13 years ago
31. 311b277 add solder jumper to bypass TPS736XX (if it is not populated) by Harald Welte · 13 years ago
32. df93fb1 add 4 test pads for RTIP/RRING/TTIP/TRING by Harald Welte · 13 years ago
33. e5fd58a re-wire SPI connector to reflect pin-out of Olimex devel board UEXT by Harald Welte · 13 years ago
34. f4a1d02 Add LDO, remove jumpers, 3nd RJ45, ... by Harald Welte · 13 years ago
35. 2f4c472 add README file by Harald Welte · 13 years ago
36. 547bc5c initial checkin by Harald Welte · 13 years ago