- e4d7fbb e1-tracer: state copyright in sch and brd by Martin Schramm · 4 years, 1 month ago
- 8c9a55d e1-tracer: PCB almost ready by Martin Schramm · 4 years, 1 month ago
- ff394bd e1-tracer: commit a first schematic by Martin Schramm · 4 years, 2 months ago
- 190cd58 increase clearance of ground planes; pad roundness by Harald Welte · 4 years, 9 months ago
- c5a57a2 enlarge board to have proper mounting holes for mechanical mounting by Harald Welte · 4 years, 9 months ago
- dfe01d4 squash most parts and avoid silk screen overlaps all over the place by Harald Welte · 4 years, 9 months ago
- 2a8c4c5 change font to vector / update to v2 by Harald Welte · 4 years, 9 months ago
- 15e6f9a e1_xcvr.brd: minor routing improvement on TRING signal by Martin Schramm · 6 years ago
- 00ebf25 replace old PULSE_T1094NL footprint, repair pin assignment (solves OSM#3269) by Martin Schramm · 6 years ago
- 8ce5748 laforge.lbr: PULSE_T1094NL: better tPlace and tDocu layer (for OSM#3270) by Martin Schramm · 6 years ago
- 69f96a6 connect LIU's pin 44 to GND (solves OSM#3247) by Martin Schramm · 6 years ago
- ed2b563 laforge.lbr: repair PULSE_T1094NL footprint and symbol (solves OSM#3270) by Martin Schramm · 6 years ago
- 5b15f68 add E1 tap hardware design by Harald Welte · 12 years ago
- ceb6ef1 laforge.lbr: fix amphenol sim reader footprint by Harald Welte · 12 years ago
- b59bfbc major update of laforge.lbr with lots of new components by Harald Welte · 12 years ago
- 638afbb 'new' PCB routing by Christian Vogel by Harald Welte · 13 years ago
- 28460ee major update of laforge.lbr with lots of new components by Harald Welte · 13 years ago
- ceb70a8 give parts names without "$", use 47nH as L1 (1206) by Harald Welte · 13 years ago
- b8dfc48 approve lots of warnings about thinner wires by Harald Welte · 13 years ago
- 71ba939 remove stray GNDIO wire, add junction, approve some warnings by Harald Welte · 13 years ago
- 5becd7e re-route complete board, add PWR jumper, LED series resistor by Christian Vogel · 13 years ago
- a40a482 add partlist/bom by Harald Welte · 13 years ago
- 372a183 update schematics and PCB layout by Harald Welte · 13 years ago
- 07c856a re-route pcb with LEDs by Harald Welte · 13 years ago
- f687f38 add two LEDs (power and LOS) plus required transistor by Harald Welte · 13 years ago
- a2c23eb re-route the entire board to add test pads and additional components by Harald Welte · 13 years ago
- 8b0e886 just name some signals/networks by Harald Welte · 13 years ago
- 311b277 add solder jumper to bypass TPS736XX (if it is not populated) by Harald Welte · 13 years ago
- df93fb1 add 4 test pads for RTIP/RRING/TTIP/TRING by Harald Welte · 13 years ago
- e5fd58a re-wire SPI connector to reflect pin-out of Olimex devel board UEXT by Harald Welte · 13 years ago
- f4a1d02 Add LDO, remove jumpers, 3nd RJ45, ... by Harald Welte · 13 years ago
- 547bc5c initial checkin by Harald Welte · 13 years ago