Gitiles
Code Review Sign In
gerrit.osmocom.org / osmo-e1-hardware / 2c3c2757a5ca6041415e965e1818cd28271d7c4b
  1. 2c3c275 osmo_e1f: Fix Makefile to use pkg-config by Sylvain Munaut · 6 years ago
  2. a3ddfb1 Merge branch 'laforge/software' by Harald Welte · 6 years ago
  3. 24531ce rename osmo_e1 to osmo_e1f ("f" for "framer") by Harald Welte · 6 years ago
  4. 82fb9b7 osmo_e1: fix make clean by Harald Welte · 6 years ago
  5. cdbcff9 CRC4: use proper CRC4 table to avoid bit-reversal of each byte by Harald Welte · 6 years ago
  6. ce18a04 add e1_test_dieter to deframe/decode dieters capture by Harald Welte · 6 years ago
  7. 8a95fd5 osmo_e1: Add HDLC framing/deframing by Harald Welte · 6 years ago
  8. 37e2374 osmo_e1: Silence the FSM logging by Harald Welte · 6 years ago
  9. 9bd2c9f HACK to make CRC4 computation work by Harald Welte · 6 years ago
  10. d3941c6 osmo_e1.c: Fix handling of TS2..31 (use 'i', not '1') by Harald Welte · 6 years ago
  11. f01471d add some information related a SAM4S based USB-to-LIU adapter board idea by Harald Welte · 6 years ago
  12. 0c756eb WIP: Software for E1 mux/demux by Harald Welte · 6 years ago
  13. 5b15f68 add E1 tap hardware design by Harald Welte · 12 years ago
  14. ceb6ef1 laforge.lbr: fix amphenol sim reader footprint by Harald Welte · 12 years ago
  15. b59bfbc major update of laforge.lbr with lots of new components by Harald Welte · 12 years ago
  16. 605e3e4 add some glue code between the idt82 driver and at91lib SPI by Harald Welte · 12 years ago
  17. 638afbb 'new' PCB routing by Christian Vogel by Harald Welte · 12 years ago
  18. 28460ee major update of laforge.lbr with lots of new components by Harald Welte · 12 years ago
  19. da02f55 add initial driver skeleton for idt82v2081 chip by Harald Welte · 12 years ago
  20. ceb70a8 give parts names without "$", use 47nH as L1 (1206) by Harald Welte · 12 years ago
  21. b8dfc48 approve lots of warnings about thinner wires by Harald Welte · 12 years ago
  22. 71ba939 remove stray GNDIO wire, add junction, approve some warnings by Harald Welte · 12 years ago
  23. 5becd7e re-route complete board, add PWR jumper, LED series resistor by Christian Vogel · 12 years ago
  24. a40a482 add partlist/bom by Harald Welte · 12 years ago
  25. 372a183 update schematics and PCB layout by Harald Welte · 12 years ago
  26. 07c856a re-route pcb with LEDs by Harald Welte · 12 years ago
  27. f687f38 add two LEDs (power and LOS) plus required transistor by Harald Welte · 12 years ago
  28. a2c23eb re-route the entire board to add test pads and additional components by Harald Welte · 12 years ago
  29. 8b0e886 just name some signals/networks by Harald Welte · 12 years ago
  30. 311b277 add solder jumper to bypass TPS736XX (if it is not populated) by Harald Welte · 12 years ago
  31. df93fb1 add 4 test pads for RTIP/RRING/TTIP/TRING by Harald Welte · 12 years ago
  32. e5fd58a re-wire SPI connector to reflect pin-out of Olimex devel board UEXT by Harald Welte · 12 years ago
  33. f4a1d02 Add LDO, remove jumpers, 3nd RJ45, ... by Harald Welte · 12 years ago
  34. 2f4c472 add README file by Harald Welte · 12 years ago
  35. 547bc5c initial checkin by Harald Welte · 12 years ago