start with USB CDC echo example
this is the Atmel START USB CDC Echo example project for the
SAM E54 Xplained Pro board using an Atmel ATSAME54P20A
microcontroller.
Atmel START information:
- Version: 1.4.1810 (Dec 18, 2018, 5:52 AM GMT+1)
- Server: 1.4.93
- Content version: 1.0.1340
This will serve as basis for the sysmoOCTSIM project
A jenkins contrib script has also been added to the
osmo-ccid-firmware project to build the sysmoOCTSIM firmware
Change-Id: I356de75e7b730d63fb819248e71d36f785932199
diff --git a/sysmoOCTSIM/hal/include/hal_gpio.h b/sysmoOCTSIM/hal/include/hal_gpio.h
new file mode 100644
index 0000000..fbfa2d4
--- /dev/null
+++ b/sysmoOCTSIM/hal/include/hal_gpio.h
@@ -0,0 +1,201 @@
+/**
+ * \file
+ *
+ * \brief Port
+ *
+ * Copyright (c) 2014-2018 Microchip Technology Inc. and its subsidiaries.
+ *
+ * \asf_license_start
+ *
+ * \page License
+ *
+ * Subject to your compliance with these terms, you may use Microchip
+ * software and any derivatives exclusively with Microchip products.
+ * It is your responsibility to comply with third party license terms applicable
+ * to your use of third party software (including open source software) that
+ * may accompany Microchip software.
+ *
+ * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES,
+ * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE,
+ * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY,
+ * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE
+ * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL
+ * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE
+ * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE
+ * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT
+ * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY
+ * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY,
+ * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE.
+ *
+ * \asf_license_stop
+ */
+#ifndef _HAL_GPIO_INCLUDED_
+#define _HAL_GPIO_INCLUDED_
+
+#include <hpl_gpio.h>
+#include <utils_assert.h>
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * \brief Set gpio pull mode
+ *
+ * Set pin pull mode, non existing pull modes throws an fatal assert
+ *
+ * \param[in] pin The pin number for device
+ * \param[in] pull_mode GPIO_PULL_DOWN = Pull pin low with internal resistor
+ * GPIO_PULL_UP = Pull pin high with internal resistor
+ * GPIO_PULL_OFF = Disable pin pull mode
+ */
+static inline void gpio_set_pin_pull_mode(const uint8_t pin, const enum gpio_pull_mode pull_mode)
+{
+ _gpio_set_pin_pull_mode((enum gpio_port)GPIO_PORT(pin), pin & 0x1F, pull_mode);
+}
+
+/**
+ * \brief Set pin function
+ *
+ * Select which function a pin will be used for
+ *
+ * \param[in] pin The pin number for device
+ * \param[in] function The pin function is given by a 32-bit wide bitfield
+ * found in the header files for the device
+ *
+ */
+static inline void gpio_set_pin_function(const uint32_t pin, uint32_t function)
+{
+ _gpio_set_pin_function(pin, function);
+}
+
+/**
+ * \brief Set port data direction
+ *
+ * Select if the pin data direction is input, output or disabled.
+ * If disabled state is not possible, this function throws an assert.
+ *
+ * \param[in] port Ports are grouped into groups of maximum 32 pins,
+ * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc
+ * \param[in] mask Bit mask where 1 means apply direction setting to the
+ * corresponding pin
+ * \param[in] direction GPIO_DIRECTION_IN = Data direction in
+ * GPIO_DIRECTION_OUT = Data direction out
+ * GPIO_DIRECTION_OFF = Disables the pin
+ * (low power state)
+ */
+static inline void gpio_set_port_direction(const enum gpio_port port, const uint32_t mask,
+ const enum gpio_direction direction)
+{
+ _gpio_set_direction(port, mask, direction);
+}
+
+/**
+ * \brief Set gpio data direction
+ *
+ * Select if the pin data direction is input, output or disabled.
+ * If disabled state is not possible, this function throws an assert.
+ *
+ * \param[in] pin The pin number for device
+ * \param[in] direction GPIO_DIRECTION_IN = Data direction in
+ * GPIO_DIRECTION_OUT = Data direction out
+ * GPIO_DIRECTION_OFF = Disables the pin
+ * (low power state)
+ */
+static inline void gpio_set_pin_direction(const uint8_t pin, const enum gpio_direction direction)
+{
+ _gpio_set_direction((enum gpio_port)GPIO_PORT(pin), 1U << GPIO_PIN(pin), direction);
+}
+
+/**
+ * \brief Set port level
+ *
+ * Sets output level on the pins defined by the bit mask
+ *
+ * \param[in] port Ports are grouped into groups of maximum 32 pins,
+ * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc
+ * \param[in] mask Bit mask where 1 means apply port level to the corresponding
+ * pin
+ * \param[in] level true = Pin levels set to "high" state
+ * false = Pin levels set to "low" state
+ */
+static inline void gpio_set_port_level(const enum gpio_port port, const uint32_t mask, const bool level)
+{
+ _gpio_set_level(port, mask, level);
+}
+
+/**
+ * \brief Set gpio level
+ *
+ * Sets output level on a pin
+ *
+ * \param[in] pin The pin number for device
+ * \param[in] level true = Pin level set to "high" state
+ * false = Pin level set to "low" state
+ */
+static inline void gpio_set_pin_level(const uint8_t pin, const bool level)
+{
+ _gpio_set_level((enum gpio_port)GPIO_PORT(pin), 1U << GPIO_PIN(pin), level);
+}
+
+/**
+ * \brief Toggle out level on pins
+ *
+ * Toggle the pin levels on pins defined by bit mask
+ *
+ * \param[in] port Ports are grouped into groups of maximum 32 pins,
+ * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc
+ * \param[in] mask Bit mask where 1 means toggle pin level to the corresponding
+ * pin
+ */
+static inline void gpio_toggle_port_level(const enum gpio_port port, const uint32_t mask)
+{
+ _gpio_toggle_level(port, mask);
+}
+
+/**
+ * \brief Toggle output level on pin
+ *
+ * Toggle the pin levels on pins defined by bit mask
+ *
+ * \param[in] pin The pin number for device
+ */
+static inline void gpio_toggle_pin_level(const uint8_t pin)
+{
+ _gpio_toggle_level((enum gpio_port)GPIO_PORT(pin), 1U << GPIO_PIN(pin));
+}
+
+/**
+ * \brief Get input level on pins
+ *
+ * Read the input level on pins connected to a port
+ *
+ * \param[in] port Ports are grouped into groups of maximum 32 pins,
+ * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc
+ */
+static inline uint32_t gpio_get_port_level(const enum gpio_port port)
+{
+ return _gpio_get_level(port);
+}
+
+/**
+ * \brief Get level on pin
+ *
+ * Reads the level on pins connected to a port
+ *
+ * \param[in] pin The pin number for device
+ */
+static inline bool gpio_get_pin_level(const uint8_t pin)
+{
+ return (bool)(_gpio_get_level((enum gpio_port)GPIO_PORT(pin)) & (0x01U << GPIO_PIN(pin)));
+}
+/**
+ * \brief Get current driver version
+ */
+uint32_t gpio_get_version(void);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif