add SERCOM peripheral for UART debug
currently only the SERCOM peripheral driver is added an configured,
but it is not being used.
UART debug will be done through the EDBG COM port, on PB24/PB25 of
SAM E54 Xplained Pro board
Change-Id: Id7af37ce1dd2d0a356e019c96bf6438ce459411b
diff --git a/sysmoOCTSIM/hal/include/hpl_i2c_s_async.h b/sysmoOCTSIM/hal/include/hpl_i2c_s_async.h
new file mode 100644
index 0000000..92a5765
--- /dev/null
+++ b/sysmoOCTSIM/hal/include/hpl_i2c_s_async.h
@@ -0,0 +1,184 @@
+/**
+ * \file
+ *
+ * \brief I2C Slave Hardware Proxy Layer(HPL) declaration.
+ *
+ * Copyright (c) 2015-2018 Microchip Technology Inc. and its subsidiaries.
+ *
+ * \asf_license_start
+ *
+ * \page License
+ *
+ * Subject to your compliance with these terms, you may use Microchip
+ * software and any derivatives exclusively with Microchip products.
+ * It is your responsibility to comply with third party license terms applicable
+ * to your use of third party software (including open source software) that
+ * may accompany Microchip software.
+ *
+ * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES,
+ * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE,
+ * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY,
+ * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE
+ * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL
+ * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE
+ * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE
+ * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT
+ * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY
+ * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY,
+ * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE.
+ *
+ * \asf_license_stop
+ *
+ */
+#ifndef _HPL_I2C_S_ASYNC_H_INCLUDED
+#define _HPL_I2C_S_ASYNC_H_INCLUDED
+
+#include "hpl_i2c_s_sync.h"
+#include "hpl_irq.h"
+#include "utils.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * \brief i2c callback types
+ */
+enum _i2c_s_async_callback_type { I2C_S_DEVICE_ERROR, I2C_S_DEVICE_TX, I2C_S_DEVICE_RX_COMPLETE };
+
+/**
+ * \brief Forward declaration of I2C Slave device
+ */
+struct _i2c_s_async_device;
+
+/**
+ * \brief i2c slave callback function type
+ */
+typedef void (*_i2c_s_async_cb_t)(struct _i2c_s_async_device *device);
+
+/**
+ * \brief i2c slave callback pointers structure
+ */
+struct _i2c_s_async_callback {
+ void (*error)(struct _i2c_s_async_device *const device);
+ void (*tx)(struct _i2c_s_async_device *const device);
+ void (*rx_done)(struct _i2c_s_async_device *const device, const uint8_t data);
+};
+
+/**
+ * \brief i2c slave device structure
+ */
+struct _i2c_s_async_device {
+ void * hw;
+ struct _i2c_s_async_callback cb;
+ struct _irq_descriptor irq;
+};
+
+/**
+ * \name HPL functions
+ */
+
+/**
+ * \brief Initialize asynchronous I2C slave
+ *
+ * This function does low level I2C configuration.
+ *
+ * \param[in] device The pointer to i2c interrupt device structure
+ *
+ * \return Return 0 for success and negative value for error
+ */
+int32_t _i2c_s_async_init(struct _i2c_s_async_device *const device, void *const hw);
+
+/**
+ * \brief Deinitialize asynchronous I2C in interrupt mode
+ *
+ * \param[in] device The pointer to i2c device structure
+ *
+ * \return Return 0 for success and negative value for error
+ */
+int32_t _i2c_s_async_deinit(struct _i2c_s_async_device *const device);
+
+/**
+ * \brief Enable I2C module
+ *
+ * This function does low level I2C enable.
+ *
+ * \param[in] device The pointer to i2c slave device structure
+ *
+ * \return Return 0 for success and negative value for error
+ */
+int32_t _i2c_s_async_enable(struct _i2c_s_async_device *const device);
+
+/**
+ * \brief Disable I2C module
+ *
+ * This function does low level I2C disable.
+ *
+ * \param[in] device The pointer to i2c slave device structure
+ *
+ * \return Return 0 for success and negative value for error
+ */
+int32_t _i2c_s_async_disable(struct _i2c_s_async_device *const device);
+
+/**
+ * \brief Check if 10-bit addressing mode is on
+ *
+ * \param[in] device The pointer to i2c slave device structure
+ *
+ * \return Cheking status
+ * \retval 1 10-bit addressing mode is on
+ * \retval 0 10-bit addressing mode is off
+ */
+int32_t _i2c_s_async_is_10bit_addressing_on(const struct _i2c_s_async_device *const device);
+
+/**
+ * \brief Set I2C slave address
+ *
+ * \param[in] device The pointer to i2c slave device structure
+ * \param[in] address Address to set
+ *
+ * \return Return 0 for success and negative value for error
+ */
+int32_t _i2c_s_async_set_address(struct _i2c_s_async_device *const device, const uint16_t address);
+
+/**
+ * \brief Write a byte to the given I2C instance
+ *
+ * \param[in] device The pointer to i2c slave device structure
+ * \param[in] data Data to write
+ */
+void _i2c_s_async_write_byte(struct _i2c_s_async_device *const device, const uint8_t data);
+
+/**
+ * \brief Retrieve I2C slave status
+ *
+ * \param[in] device The pointer to i2c slave device structure
+ *
+ *\return I2C slave status
+ */
+i2c_s_status_t _i2c_s_async_get_status(const struct _i2c_s_async_device *const device);
+
+/**
+ * \brief Abort data transmission
+ *
+ * \param[in] device The pointer to i2c device structure
+ *
+ * \return Return 0 for success and negative value for error
+ */
+int32_t _i2c_s_async_abort_transmission(const struct _i2c_s_async_device *const device);
+
+/**
+ * \brief Enable/disable I2C slave interrupt
+ *
+ * param[in] device The pointer to I2C slave device instance
+ * param[in] type The type of interrupt to disable/enable if applicable
+ * param[in] disable Enable or disable
+ */
+int32_t _i2c_s_async_set_irq_state(struct _i2c_s_async_device *const device, const enum _i2c_s_async_callback_type type,
+ const bool disable);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* _HPL_I2C_S_ASYNC_H_INCLUDED */